2006 ACURA CSX bulb

Cavity Wire Test conditionTest: Desired result Possible cause if result desired is
not obtained
22-190Turn Signal/Hazard Warning Lights
MICU Input Test (cont’d)
5. With the connectors still disconnected, do these input tests at the following connectors.
 If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, go to step 6.
























E39 BRN Under all conditions Connect terminals G2 and E39
with a jumper wire:
The right rear turn signal light
should come on.Poor ground (G701)
Blown bulb
An open in the wire
E40 BLU Under all conditions Connect terminals G2 and E40 with a jumper wire:
The left rear turn signal light
should come on.Poor ground (G701)
Blown bulb
An open in the wire
F1 BRN Under all conditions Connect terminals G2 and F1 with a jumper wire:
The right front turn signal light
should come on.Poor ground (G201)
Blown bulb
An open in the wire
G1 BLU Under all conditions Connect terminals G2 and G1 with a jumper wire:
The left front turn signal light
should come on.Poor ground (G301)
Blown bulb
An open in the wire
M1 BLU Under all conditions Connect terminals G2 and M1 with a jumper wire:
The left side turn signal light
should come on.Poor ground (G503)
Blown LED
An open in the wire
M2 GRN Under all conditions Connect terminals G2 and M2 with a jumper wire:
The right side turn signal light
should come on.Poor ground (G502)
Blown LED
An open in the wire
P1 GRN Under all conditions Connect terminals G2 and P1 with a jumper wire:
The right turn signal indicator
should come on.Poor ground (G504)
Faulty gauge control module
(speedo)
An open in the wire
P6 BLU Under all conditions Connect terminals G2 and P6 with a jumper wire:
The left turn signal indicator
should come on.Poor ground (G504)
Faulty gauge control module
(speedo)
An open in the wire
08/08/21 14:27:44 61SNR030_220_0192
ProCarManuals.com
DYNOMITE -2009-



(#'


) 

(#'
 )
22-19222-192 Turn Signal/Hazard Warning Lights
Hazard Warning Switch Test/
Replacement
Side Turn Signal Light Replacement
A
A
Terminal
Position 12
4
5
OFF ON A
A
B
1. Remove the center panel.  With audio:– ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
 With navigation: – ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
2. Remove the screws and the hazard warning switch (A).
3. Check for continuity between the terminals in each switch position according to the table.
4. If the continuity is not as specified, replace the bulb (A) or the hazard warning switch.
5. Install the hazard warning switch in the reverse order of removal. 1. Remove the mirror holder (see page 20-34).
2. Remove the four screws and the mirror visor (A).
3. Disconnect the 2P connector (A) from the side turn
signal light (B), then remove the side turn signal
light.
4. Install the side turn signal light in the reverse order of removal.
08/08/21 14:27:45 61SNR030_220_0194
ProCarManuals.com
DYNOMITE -2009-

Î

(#'
)
 Î

(#'
)

With moonroof Without moonroof
Front Individual Map Light: 8 W x 2 Front Individual Map Light: 8 W x 2
22-19622-196Interior Lights
Front Individual Map Light Test/Replacement
A
B
C
Position 13
Terminal
RIGHT LEFT ON
OFF ON
OFF Body
ground A
B
C
Position 1
Terminal
RIGHT LEFT ON
OFF ON
OFF Body
ground
1. Turn the map light switch OFF.
2. Carefully pry the lens (A) off with a small
screwdriver.
3. Remove the screws, then remove the map lights (B) and moonroof switch or navigation microphone (C).
4. Disconnect the 3P connector from the map lights and the 10P connector from the moonroof switch or
navigation microphone.
5. Check for continuity between the terminals in each switch position according to the table.
6. If the continuity is not as specified, check the bulb(s). If the bulb(s) are OK, replace the light
assembly.
7. Install the map light in the reverse order of removal. 1. Turn the map light switch OFF.
2. Carefully pry the lens (A) off with a small
screwdriver.
3. Remove the screws, then remove the map lights (B).
4. Disconnect the 3P connector (C) from the map lights.
5. Check for continuity between the terminals in each switch position according to the table.
6. If the continuity is not as specified, check the bulb(s). If the bulb(s) are OK, replace the light
assembly.
7. Install the map light in the reverse order of removal.
08/08/21 14:27:50 61SNR030_220_0198
ProCarManuals.com
DYNOMITE -2009-


(#'

)
 ´
µ 
(#'
)
´ µ
Ceiling Light: 8 W Trunk Light: 5 W
22-19722-197
Ceiling Light Test/Replacement Trunk Light Test/Replacement
AC
B A
B
() ()
1. Turn the ceiling light switch OFF.
2. Carefully pry the lens (A) off with a small
screwdriver.
3. Remove the screws, then remove the ceiling light (B).
4. Disconnect the 3P connector (C) from the ce iling
light.
5. Check for continuity between the terminals.  There should be continuity between terminalsNo. 1 and No. 2 with the switch in the MIDDLE
position.
 There should be continuity between terminals No. 2 and No. 3 (Body ground) with the switch in
the ON position.
 There should be no continuity between terminals No. 1 and No. 2, and between No. 2 and body
ground with the switch in the OFF position.
6. If the continuity is not as specified, check the bulb. If the bulb is OK, replace the light.
7. Install the ceiling light in the reverse order of removal. 1. Open the trunk lid.
2. Carefully pry out the trunk light (A).
3. Disconnect the 2P connector (B) from the light.
4. Check for continuity between terminals No. 1 ( )
and No. 2 ( ). There should be continuity. If there
is no continuity, check the bulb. If the bulb is OK,
replace the trunk light assembly.
5. Install the trunk light in the reverse order of removal.
08/08/21 14:27:50 61SNR030_220_0199
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
) 
(#'

 ) Courtesy light: 3.4 W
22-19822-198
Interior Lights
Ambient Light Test/Replacement Courtesy Light Replacement
A
B
C ’06-07 models
’08-09 models
A
B C
D
1. Remove the front individual map light.
 With moonroof (see page 22-196)
 Without moonroof (see page 22- 196)
2. Disconnect the 10P (or 12P ) connector (A) from the ambient light (B), then remove the ambient
light from the front individual map light housing (C).
1: ’06-07 models
2: ’08-09 models
3. Connect battery power to the terminal No. 5 and ground to the No. 3 terminal. The ambient light
should turn on. If the light does not turn on, replace
the ambient light.
4. Install the ambient light in the reverse order of removal. 1. Carefully pry off the lens (A) with a small
screwdriver.
2. Pry out the housing (B) from the door panel, then disconnect the 2P connector (C).
3. Separate the housing, then remove the bulb (D) from the socket.
4. Install the courtesy light in the reverse order of removal.
12
08/08/21 14:27:50 61SNR030_220_0200
ProCarManuals.com
DYNOMITE -2009-


(#'


) 
(#'

)
Glove Box Light: 3.4 W
Vanity Mirror Light: 2 W
’08-09 models
22-19922-199
Glove Box Light Test/Replacement Vanity Mirror Light Test/Replacement
B
A C
A B
C
1. Open the glove box.
2. Remove the screws, then disconnect the 2P
connector from the glove box light (A).
3. Check for continuity between terminals No. 1 and No. 2.
 There should be continuity with the switch (B) released.
 There should be no continuity with the switch (B) pushed.
4. If the continuity is not as specified, check the bulb (C). If the bulb is OK, replace the light.
5. Install the glove box light in the reverse order of removal. 1. Open the sunvisor.
2. Remove the sunvisor (see page 20-84).
3. Disconnect the 2P connector (A) from the vanity
mirror light.
4. Check for continuity between terminals No. 1 and No. 2.
 With the vanity mirror cover (B) opened, there should be continuity.
 With the vanity mirror cover closed, there should be no continuity.
5. If the continuity is not as specified, replace the bulb (C) or the sunvisor.
6. Install the vanity mirror light in the reverse order of removal.
08/08/21 14:27:51 61SNR030_220_0201
ProCarManuals.com
DYNOMITE -2009-

Cavity Wire Test condition Test: Desired result Possible cause if desired result is not obtained
22-205
UNDER-DASH FUSE/RELAY BOX
CONNECTOR K (8P)
PNK
WHT BLK
PNK
UNDER-DASH FUSE/RELAY BOX
CONNECTOR R (20P)
UNDER-DASH FUSE/RELAY BOX
CONNECTOR T (34P)
4. Inspect the connector and socket terminals to be sure they are all making good contact.  If the terminals are bent, loose or corroded, repair them as necessary and recheck the system.
 IftheterminalslookOK,gotostep5.
5. With the connectors still disconnected, do this input test at the following connector.  If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, go to step 6.






K4 PNK With the ceiling light
switch in the middle
position
With moonroof:
with the interior light
switch in DOOR
position Attach to ground:
The ceiling light and front
individual map lights should
come on.
Blown No. 22 (7.5 A) fuse in
the under-hood fuse/relay
box
Blown bulb(s)
Faulty ceiling light
Faulty front individual map
light
Faulty interior light switch
(with moonroof)
An open in the wire
(cont’d)
08/08/21 14:27:54 61SNR030_220_0207
ProCarManuals.com
DYNOMITE -2009-


(#'

)

Î
(#'

)
´
´
’06-07 models ’08-09 models
22-29322-293
Moonroof Switch Test/Replacement
CB
A
Terminal
Position
OPEN
CLOSE TILT
CLOSE AUTO OPEN AUTO 7269104 5 B
C A
Terminal
Position
OPEN
CLOSE TILT
CLOSE AUTO OPEN AUTO 5
8 4610
23
*1: Except Type S model
*2: Type S model *
*
1
2
1. Remove the front individual map lights (see page 22-196).
2. Disconnect the moonroof switch 10P connector (A) and map light switch 3P connector (B).
3. Remove the moonroof switch (C).
4. Check for continuity between the terminals in each switch position according to the table.
5. If the continuity is not as specified, replace the illumination bulb or the switch.
6. Install the moonroof switch and light in the r everse
order of removal. 1. Remove the front individual map lights (see page
22-196).
2. Disconnect the moonroof switch 12P connector (A) and map light switch 3P connector (B).
3. Remove the moonroof switch (C).
4. Check for continuity between the terminals in each switch position according to the table.
5. If the continuity is not as specified, replace the illumination bulb or the switch.
6. Install the moonroof switch and light in the reverse order of removal.
08/08/21 14:36:06 61SNR030_220_0295
ProCarManuals.com
DYNOMITE -2009-