2006 ACURA CSX sensor

Î
 
(#'
 )
6-386-38 Cylinder Head
Cylinder Head Cover Installation
(cont’d)
Cylinder Head Removal
B
C
A
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) A
B
8. Install two bolts (A) securing the evaporativeemission (EVAP) canister purge valve bracket.
9. Connect the breather hose (B), and install the dipstick (C).
10. Connect the evaporative emission (EVAP) canister purge valve connector.
11. Install the four ignition coils (see page 4-21).
12. Install the engine cover. NOTE:
 Use fender covers to avoid damaging the painted surfaces.
 To avoid damaging the wire and terminals, unplug the wiring connectors carefully while holding the
connector portion.
 Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3),
and monitor the engine coolant temperature (ECT)
sensor 1. To avoid damaging the cylinder head, wait
until the engine coolant temperature drops below
38 °C (100 °F) before loosening the cylinder head
bolts.
 Mark all wiring and hoses to avoid misconnection. Also, be sure that they do not contact other wiring or
hoses, or interfere with other parts.
1. Relieve the fuel pressure (see page 11-322).
2. Drain the engine coolant (see page 10-8).
3. Remove the air cleaner assembly (see page 11-345).
4. Remove the drive belt (see page 4-31).
5. Remove the intake manifold:  K20Z2 engine (see page 9-3)
 K20Z3 engine (see page 9-7)
6. Remove the exhaust manifold (see page 9-11).
7. Disconnect the evaporative emission (EVAP) canister hose (A) and the brake booster vacuum
hose (B).
08/08/21 14:27:27 61SNR030_060_0038
ProCarManuals.com
DYNOMITE -2009-

Î
 
(#'
 )
6-386-38 Cylinder Head
Cylinder Head Cover Installation
(cont’d)
Cylinder Head Removal
B
C
A
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) A
B
8. Install two bolts (A) securing the evaporativeemission (EVAP) canister purge valve bracket.
9. Connect the breather hose (B), and install the dipstick (C).
10. Connect the evaporative emission (EVAP) canister purge valve connector.
11. Install the four ignition coils (see page 4-21).
12. Install the engine cover. NOTE:
 Use fender covers to avoid damaging the painted surfaces.
 To avoid damaging the wire and terminals, unplug the wiring connectors carefully while holding the
connector portion.
 Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3),
and monitor the engine coolant temperature (ECT)
sensor 1. To avoid damaging the cylinder head, wait
until the engine coolant temperature drops below
38 °C (100 °F) before loosening the cylinder head
bolts.
 Mark all wiring and hoses to avoid misconnection. Also, be sure that they do not contact other wiring or
hoses, or interfere with other parts.
1. Relieve the fuel pressure (see page 11-322).
2. Drain the engine coolant (see page 10-8).
3. Remove the air cleaner assembly (see page 11-345).
4. Remove the drive belt (see page 4-31).
5. Remove the intake manifold:  K20Z2 engine (see page 9-3)
 K20Z3 engine (see page 9-7)
6. Remove the exhaust manifold (see page 9-11).
7. Disconnect the evaporative emission (EVAP) canister hose (A) and the brake booster vacuum
hose (B).
08/08/21 14:27:27 61SNR030_060_0038
ProCarManuals.com
DYNOMITE -2009-


6-40Cylinder Head
Cylinder Head Removal (cont’d)
B
A
12. Remove the bolt (A) securing the connecting pipe.
13. Disconnect the water bypass hose (B).
14. Disconnect the following engine wire harnessconnectors, and remove the wire harness clamps
from the cylinder head.
 Four fuel injector connectors
 Engine coolant temperature (ECT) sensor 1 connector
 Camshaft position (CMP) sensor A (Intake) connector
 Camshaft position (CMP) sensor B (Exhaust) connector
 Rocker arm oil control valve connector
 Rocker arm oil pressure switch connector
 EVAP canister purge valve connector
 Variable valve timing control (VTC) oil control solenoid valve connector
 Exhaust gas recirculation (EGR) valve connector (K20Z2 engine)
 Engine oil pressure switch connector 15. Remove the cam chain (see page 6-18).
16. Remove the rocker arm assembly:
 K20Z2 engine (see page 6-43)
 K20Z3 engine (see page 6-44)
17. Remove the cylinder head bolts. To prevent warpage, loosen the bolts in sequence 1/3 turn at a
time. Repeat the sequence until all bolts are
loosened.
18. Remove the cylinder head.
08/08/21 14:27:28 61SNR030_060_0040
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
 

(#'



 )
6-416-41
CMP Pulse Plate A Replacement CMP Pulse Plate B Replacement
14x1.0mm
39 N·m
(4.0 kgf·m, 29 lbf·ft) 14x1.0mm
39 N·m
(4.0 kgf·m, 29 lbf·ft)
1. Remove the cylinder head cover (see page 6-36).
2. Remove camshaft position (CMP) sensor A
(see page 11-295).
3. Hold the intake camshaft with an open-end wrench, then loosen the bolt.
4. Remove CMP pulse plate A.
5. Install CMP pulse plate A in the reverse order of removal. 1. Remove the cylinder head cover (see page 6-36).
2. Remove camshaft position (CMP) sensor B
(see page 11-222).
3. Hold the exhaust camshaft with an open-end wrench, then loosen the bolt.
4. Remove CMP pulse plate B.
5. Install CMP pulse plate B in the reverse order of removal.
Apply new engine oil to the
bolt threads. Apply new engine oil to the
bolt threads.
08/08/21 14:28:11 61SNR030_060_0041
ProCarManuals.com
DYNOMITE -2009-



6-64Cylinder Head
Cylinder Head Installation (cont’d)
B
A
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft) A
B
A
B
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
12. Install the rocker arm assembly:
 K20Z2 engine (see page 6-60)
 K20Z3 engine (see page 6-61)
13. Install the cam chain (see page 6-21).
14. Connect the following engine wire harness connectors, and install the wire harness clamps to
the cylinder head:
 Four fuel injector connectors
 Engine coolant temperature (ECT) sensor 1 connector
 Camshaft position (CMP) sensor A (Intake) connector
 Camshaft position (CMP) sensor B (Exhaust) connector
 Rocker arm oil control valve connector
 Rocker arm oil pressure switch connector
 EVAP canister purge valve connector
 Variable valve timing control (VTC) oil control solenoid valve connector
 Exhaust gas recirculation (EGR) valve connector (K20Z2 engine)
 Engine oil pressure switch connector
15. Install the bolt (A) securing the connecting pipe.
16. Connect the water bypass hose (B). 17. Connect the upper radiator hose (A) and the heater
hoses (B).
18. Install the harness holder bracket (A), then install the harness holder (B).
08/08/21 14:28:43 61SNR030_060_0064
ProCarManuals.com
DYNOMITE -2009-


(#'
 )
Exploded View - K20Z2 engine
9-2Intake Manifold and Exhaust System
Intake Manifold Removal and Installation
INTAKE AIR BYPASS (IAB)
THERMAL VALVE
JOINT GASKET
THROTTLE BODY
INTAKE MANIFOLD BRACKET
MANIFOLD
ABSOLUTE
PRESSURE
(MAP)
SENSOR INJECTOR BASE
EXHAUST GAS
PRECIRCULATION
(EGR) PLATE 6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft) 8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
GASKET
INTAKE MANIFOLD
O-RING
5x0.8mm
3.4 N·m
(0.35 kgf·m, 2.5 lbf·ft)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
GASKET
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
GASKET
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) 6x1.0mm
12 N·m
(1.2 kgf·m,
8.7 lbf·ft)
INTAKE MANIFOLD
CHAMBER
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
GASKET
MARK
Tigten the valve to 15 N·m
(1.5 kgf·m, 11 lbf·ft), then turn the
valve joint toward the mark.
Replace.
Replace if cracked or
if mating surface is
damaged.
Replace.
Replace if cracked or
if mating surface is
damaged.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:37:29 61SNR030_090_0002
ProCarManuals.com
DYNOMITE -2009-



Î
Removal - K20Z2 engine
9-3
A
B C A
B
C D
A
1. Remove the engine cover.
2. Disconnect the vacuum hose (A) and the breatherpipe (B), then remove the intake air duct (C). 3. Disconnect the engine wire harness connectors,
and remove the wire harness clamps from the
intake manifold:
 Manifold absolute pressure (MAP) sensor connector
 Throttle actuator connector
4. Disconnect the evaporative emission (EVAP) canister hose (A) and the brake booster vacuum
hose (B).
5. Remove the harness bracket mounting bolt (C) and the brake booster vacuum line bracket mounting
bolt (D).
6. Disconnect the water bypass hoses (A), then plug the water bypass hoses.
(cont’d)
08/08/21 14:37:30 61SNR030_090_0003
ProCarManuals.com
DYNOMITE -2009-

Î





9-5
A
A
B
C
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft) D
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
B
C A
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
6. Connect the water bypass hoses (A).
7. Connect the evaporative emission (EVAP) canister hose (A) and the brake booster vacuum hose (B).
8. Install the harness bracket mounting bolt (C) and the brake booster vacuum line bracket mounting
bolt (D).
9. Connect the engine wire harness connectors, and install the wire harness clamps to the intake
manifold.
 Manifold absolute pressure (MAP) sensor connector
 Throttle actuator connector 10. Install the intake air duct (A), then connect the
vacuum hose (B) and the breather pipe (C).
11. Install the engine cover.
12. After installation, check that all tubes, hoses and connectors are installed correctly.
13. Clean up any spilled engine coolant.
14. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
08/08/21 14:37:32 61SNR030_090_0005
ProCarManuals.com
DYNOMITE -2009-