(#'
'
)
´
µ
µ µ
µ
YES
NO YES
NO
DTC 61-01:
DTC 61-21:
DTC 61-22:
DTC 61-23:
19-8119-81
ABS MODULATOR-CONTROL UNIT 25P CONNECTOR
FSR B (WHT)
14. Disconnect the ABS modulator-control unit 25Pconnector (see step 2 on page 19-90).
15. Measure the voltage between ABS modulator- control unit 25P connector terminal No. 8 and body
ground.
Check for loose terminals in the ABS
modulator-control unit 25P connector. If necessary,
substitute a known-good ABS modulator-control
unit (see page 19-90), and retest.
Repair open in the wire between the No. 3
(30 A) fuse in the under-hood fuse/relay box and
the ABS modulator-control unit. 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then start the
engine.
4. Check for DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for loose terminals at the ABS
modulator-control unit 25P connector. Refer to
intermittent failures troubleshooting (see page
19-50).
5. Check and note BATTERY voltage in the ABS DATA LIST with the HDS.
6. Using a voltmeter, measure and note the voltage between the battery terminals.
NOTE: If the battery voltage is below 9.5 V, check
the battery (see page 22-67), and troubleshoot the
alternator regulator circuit (see page 4-28).
(cont’d)ABS Modulator-control Unit Initial
IG Low Voltage
ABS Modulator-control Unit
Power Source Low Voltage 1
ABS Modulator-control Unit
Power Source Low Voltage 2
ABS Modulator-control Unit
Power Source Low Voltage 3
Wire side of female terminals
I s t her e bat t er y v ol t age? I s DT C 61-01, 61-21, 61-22, or 61-23 i nd i cat ed ?
08/08/21 15:03:16 61SNR030_190_0081
ProCarManuals.com
DYNOMITE -2009-
(#'
'
)
´
µ
µ µ
µ
YES
NO YES
NO
DTC 52-12:
19-14019-140VSA System Components
DTC Troubleshooting (cont’d)
MR B (RED)
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
14. Disconnect the VSA modulator-control unit 37P
connector (see step 2 on page 19- 171).
15. Measure the voltage between VSA modulator- control unit 37P connector terminal No. 14 and
body ground.
Check for loose terminals in the VSA
modulator-control unit 37P connector. If necessary,
substitute a known-good VSA modulator-control
unit (see page 19-171), and retest.
Repair open in the wire between the No. 3
(30 A) fuse in the under-hood fuse/relay box and
the VSA modulator-control unit. 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it to
ON (II) again.
4. Operate any one of the four solenoids, as listed, in the VSA FUNCTION TEST five times with the HDS.
-LFT FT SOLENOID
-RT FT SOLENOID
-LFT REAR SOLENOID
-RT REAR SOLENOID
5. Check for DTCs with the HDS.
Replace the VSA modulator-control unit
(see page 19-171).
Intermittent failure, the system is OK at this
time.Motor Stuck OFF
Wire side of female terminals
Is there battery voltage? Is DTC 52-12 indicated?
08/08/21 15:05:56 61SNR030_190_0140
ProCarManuals.com
DYNOMITE -2009-
Î
Î
´
µ
µ
µ
µ µ
µ
YES
NO
YES
NO Sign
YES
NO
VSA Modulator- control Unit 37P
Connector Terminal Gauge Control
Module (Tach) 36P
Connector Terminal
19-167
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
GND (BLK)
VSA MODULATOR-CONTROL UNIT 37P CONNECTOR FSR B (WHT) VSA MODULATOR-CONTROL UNIT 37P CONNECTOR
CAN-L (RED)CAN-L (RED)
CAN-H (WHT) CAN-H (WHT)
GAUGE CONTROL MODULE (TACH) 36P CONNECTOR
13. Check for continuity between VSA modulator- control unit 37P connector terminal No. 36 and
body ground.
Go to step 14.
Repair open in the wire between the VSA
modulator-control unit and body ground (G 202).
14. Measure the voltage between VSA modulator- control unit 37P connector terminal No. 13 and
body ground.
Go to step 15.
Repair open in the wire between the No. 3
(40 A) fuse in the under-hood fuse/relay box and
the VSA modulator-control unit. 15. Disconnect the gauge control module (tach) 36P
connector.
16. Check for continuity between VSA modulator- control unit 37P connector terminal and gauge
control module (tach) 36P connector terminal (see
table).
CAN-L No. 1 No. 19
CAN-H No. 15 No. 1
Check for loose terminals in the VSA
modulator-control unit 37P connector. If necessary,
substitute a known-good VSA modulator-control
unit (see page 19-171), and retest.
Repair open in the wire between the gauge
control module (tach) and the VSA modulator-
control unit.
Wire side of female terminals
Wire side of female terminals Wire side of female terminals
Wire side of female terminals
Is there continuity?
Is there battery voltage? Is there continuity?
08/08/21 15:06:45 61SNR030_190_0167
ProCarManuals.com
DYNOMITE -2009-
Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior TrimFenderwell
Openers
Frame......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
Component Location Index
. 20-116
Front Seat Active Head Restraint Inspection . 20-117
Front Seat Removal/Installation . 20-118
Front Seat Frame Replacement . 20-120
Front Seat-back Cover Replacement . 20-123
Front Seat Cushion Cover Replacement . 20-127
Rear Seat Removal/Installation . 20-131
Rear Seat-back Latch Replacement . 20-135
Rear Seat-back Release Lever/Cable Removal/Installation . 20-136
Rear Seat Armrest Beverage Holder Replacement . 20-137
Rear Seat Armrest Replacement . 20-138
Rear Seat-back Cover Replacement . 20-139
Rear Seat Side Bolster Cover Replacement . 20-143
Rear Seat Cushion Cover Replacement . 20-143
Rear Seat Armrest Cover Replacement . 20-144
.........
...........................................
........................................... ..........
........................................... .........
...........................................
........................................... ..........
...........................................
Front Bumper Removal/Installation . 20-146
Front Bumper Lower Grille
Replacement . 20-148
Front Bumper Lower Side Plate Replacement . 20-148
Rear Bumper Removal/Installation . 20-149
Rear Bumper Lower Cover Replacement . 20-151
...................................... ................................................
......................................
................................................
Hood Adjustment
. 20-152
Hood Seal Replacement . 20-153
Hood Insulator Replacement . 20-154
................................ ..............
..............
................................
..............
..............
Trunk Lid Adjustment
. 20-155
Trunk Lid Torsion Bar Replacement . 20-156
Trunk Lid Weatherstrip Replacement . 20-157
Trunk Lid Cushion Replacement . 20-157
.........................................
.........................
................
Fuel Fill Door Adjustment
. 20-158
Fuel Cap Adapter Replacement . 20-159
........................................
...............
.......................... ......................
...................... ...
..............
................
..................
..........................
..............
...............
.......................... ......................
...................... ...
..............
................
..................
Front Grille Replacement
. 20-160
Front Fender Trim Replacement . 20-162
Front Grille Cover Replacement . 20-163
Cowl Cover Replacement . 20-163
Roof Molding Replacement . 20-165
Door Molding Replacement . 20-167
Side Sill Protection Tape Replacement . 20-168
Rear License Trim Replacement . 20-168
Trunk Lid Spoiler Replacement . 20-169
Emblem/Sticker Replacement . 20-170 .............
...................... ............
......
.............
.............
......................... .................... .............
...................... ............
......
.............
.............
......................... ....................
Front Inner Fender Replacement . 20-171
Splash Shield Replacement
. 20-172
Front Fender Fairing Replacement . 20-173
Middle Floor Undercover Replacement . 20-174
Rear Floor Undercover Replacement . 20-174
Fuel Pipe Protector Replacement . 20-175
Rear Fender Cover Replacement . 20-175
Rear Strake Replacement . 20-176
Rear Air Outlet Replacement . 20-176
...................... ............
..................
..........................
........................................... .....
...................
......................
............
..................
..........................
........................................... .....
...................
Component Location Index
. 20-177
Hood Opener Cable Replacement . 20-178
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement . 20-179
Hood Latch Replacement . 20-181
Trunk Lid Opener/Fuel Fill Door Opener Replacement . 20-182
Trunk Lid Lock Cylinder Replacement . 20-184
Trunk Lid Latch Replacement . 20-185
...........................................
........................................... ............................
...................................
...........................................
...........................................
............................
...................................
Upper Dashboard Support Gusset
Replacement . 20-186
Rear Floor Upper Cross-member Gusset Replacement . 20-186
Subframe Replacement . 20-187
Frame Repair Chart . 20-188
08/08/21 14:58:49 61SNR030_200_0003
ProCarManuals.com
DYNOMITE -2009-
(#'
)
20-15320-153
Hood Seal Replacement
Fastener Locations : Clip, 7
A
B B
6. Check that the hood opens properly and closes
securely.
7. Apply touch-up paint to the hinge mounting bolts and around the hinges, and let the paint dry.
8. Apply multipurpose grease to the hood latch and hood hinges as indicated by the arrows.
9. Reinstall all of the removed parts. 1. Detach the clips with a clip remover, then remove
the hood seal (A) and hood corner seals (B). Take
care not to scratch the hood.
2. Install the seals in the reverse order of removal, and if the clips are damaged or stress-whitened,
replace them with new ones.
08/08/21 15:04:56 61SNR030_200_0155
ProCarManuals.com
DYNOMITE -2009-
(#'
)
20-15320-153
Hood Seal Replacement
Fastener Locations : Clip, 7
A
B B
6. Check that the hood opens properly and closes
securely.
7. Apply touch-up paint to the hinge mounting bolts and around the hinges, and let the paint dry.
8. Apply multipurpose grease to the hood latch and hood hinges as indicated by the arrows.
9. Reinstall all of the removed parts. 1. Detach the clips with a clip remover, then remove
the hood seal (A) and hood corner seals (B). Take
care not to scratch the hood.
2. Install the seals in the reverse order of removal, and if the clips are damaged or stress-whitened,
replace them with new ones.
08/08/21 15:04:56 61SNR030_200_0155
ProCarManuals.com
DYNOMITE -2009-
Î
(#'
)
20-177
Openers
Component Location Index
TRUNK LID LOCK CYLINDER
TRUNK LID LATCH
FUEL FILL
DOOR LATCH
TRUNK LID OPENER CABLE/
FUEL FILL DOOR OPENER CABLE
HOOD OPENER CABLE HOOD LATCH
TRUNK LID OPENER/
FUEL FILL DOOR OPENER
HOOD RELEASE HANDLE Replacement, page 20-184
Replacement,page 20-185
Replacement, page 20-179
Replacement, page 20-178 Replacement, page 20-181
Replacement, page 20-182
08/08/21 15:05:10 61SNR030_200_0179
ProCarManuals.com
DYNOMITE -2009-
(#'
)
20-178Openers
Hood Opener Cable Replacement
Fastener Locations
A
B
D
E EG
C
C 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
E E
D
F
:Bolt,2
C
:Clip,4
E :Clip,1
F
NOTE:
Put on gloves to protect your hands.
Take care not to scratch the body and related parts.
1. Remove these items: Front grille cover (see page 20-163)
Front inner fender, driver’s side (see page 20-171)
Kick panel, driver’s side (see page 20-66)
2. Disconnect the hood opener cable (A) from the hood latch (B) (see page 20- 181), and remove the bolts (C), then
remove the hood release handle (D). Take care not to kink the cable.
3. Detach the clips (E) with a clip remover, release the hood opener cable from the clip (F), and remove the grommet (G) from the body, then remove the hood opener cable from the vehicle. Take care not to kink the cable.
4. Install the cable in the reverse order of removal, and if the clips are damaged or stress-whitened, replace them with new ones.
08/08/21 15:05:10 61SNR030_200_0180
ProCarManuals.com
DYNOMITE -2009-