2006 ACURA CSX Idle Air Control

µµ
´ ´
Ó
ECM/PCM Inputs and Outputs at Connector C ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-31
NOTE: Standard battery voltage is about 12 V.
1 WHT IG1ETCS (IGNITION SIGNAL ETCS) Detects ignition signal With ignition switch ON (II): battery voltage
2 BLK PGMETCS (POWER GROUND ETCS) Ground circuit for ECM/
PCMLess than 1.0 V at all times
3 GRN/YEL ETCSM (THROTTLE ACTUATOR SIDE) Ground for throttle actuator With ignition switch ON (II): about 0 V
4 BLU/RED ETCSM (THROTTLE ACTUATOR SIDE) Drives throttle actuator With ignition switch ON (II): about 0 V
5 BRN INJ1 (No. 1 INJECTOR) Drives No. 1 injector At idle: duty controlled With ignition switch ON (II): battery voltage
6 RED INJ2 (No. 2 INJECTOR) Drives No. 2 injector
7 BLU INJ3 (No. 3 INJECTOR) Drives No. 3 injector
8 YEL INJ4 (No. 4 INJECTOR) Drives No. 4 injector
9 WHT/GRN AFSHTC (AIR FUEL RATIO
(A/F) SENSOR HEATER
CONTROL (SENSOR 1)) Drives A/F sensor heater
(sensor 1)
With ignition switch ON (II): battery voltage
With fully warmed up engine running: about 0 V
11 GRN/RED MAP (MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR) Detects MAP sensor signal With ignition switch ON (II): about 3.0 V
At idle: about 1.0 V (depending on engine speed)
12 BLU VCC3 (SENSOR VOLTAGE) Provides sensor reference voltageWith ignition switch ON (II): about 5.0 V
13 YEL/RED VCC1 (SENSOR VOLTAGE) Provides sensor reference voltageWith ignition switch ON (II): about 5.0 V
14 GRN/WHT SG1 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
15 YEL/GRN IGPLS1 (No. 1 IGNITION COIL PULSE) Drives No. 1 ignition coil With ignition switch ON (II): about 0 V
With engine running: pulses
16 BLU/RED IGPLS2 (No. 2 IGNITION COIL PULSE) Drives No. 2 ignition coil
17 WHT/BLU IGPLS3 (No. 3 IGNITION COIL PULSE) Drives No. 3 ignition coil
18 BRN IGPLS4 (No. 4 IGNITION COIL PULSE) Drives No. 4 ignition coil
20 RED/BLK TPSA (THROTTLE POSITION (TP) SENSOR A) Detects TP sensor A signal With throttle fully open: about 3.9 V
With throttle fully closed: about 0.9 V
21 RED/BLU TPSB (THROTTLE POSITION (TP) SENSOR B) Detects TP sensor B signal With throttle fully open: about 4.1 V
With throttle fully closed: about 1.7 V
(cont’d)
Terminal side of female terminals
08/08/21 14:13:36 61SNR030_110_0031
ProCarManuals.com
DYNOMITE -2009-

´
´ µ
µ
Ó
ECM/PCM Inputs and Outputs at Connector C ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-32Fuel and Emissions Systems
System Description (cont’d)
NOTE: Standard battery voltage is about 12 V.
22 BLU/BLK VTPSW (ROCKER ARM OIL PRESSURE SWITCH) Detects rocker arm oil
pressure switch signalWith engine at low speed: about 0 V
With engine at high speed: battery voltage
23 BLU/WHT VTC (VTC OIL CONTROL SOLENOID VALVE) Drives VTC oil control
solenoid valvewith ignition switch ON (II): about 0 V
27 WHT/RED SHO2S (SECONDARY HEATED OXYGEN SENSOR
(SECONDARY HO2S)
(SENSOR 2)) Detects secondary HO2S
(sensor 2) signal
With throttle fully opened from idle and warmed up
engine: about 0.6 V
With throttle quickly closed: below 0.4 V
29 RED AFS (AIR FUEL RATIO (A/F) SENSOR (SENSOR 1)SIDE) Detects A/F sensor
(sensor 1) signal
30 RED/YEL AFS (AIR FUEL RATIO (A/F) SENSOR (SENSOR 1)SIDE) Detects A/F sensor
(sensor 1) signal
31 GRN CMPB (CAMSHAFT POSITION (CMP) SENSOR
B) Detects CMP sensor B
signal
With engine running: pulses
32 BLU/YEL CKP (CRANKSHAFT POSITION (CKP) SENSOR) Detects CKP sensor signal With engine running: pulses
36 BLK/GRN IG1 (IGNITION SIGNAL) Detects ignition signal With ignition switch ON (II): battery voltage
39 GRN SG3 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
40 BRN/YEL LG1 (LOGIC GROUND) Ground circuit for ECM/ PCMLess than 1.0 V at all times
41 BLU/WHT CMPA (CAMSHAFT POSITION (CMP) SENSOR
A) Detects CMP sensor A
signal
With engine running: pulses
42 RED/BLU KS (KNOCK SENSOR) Detects knock sensor signal With engine knocking: pulses
43 BLK/WHT NC (OUTPUT SHAFT (COUNTERSHAFT) SPEED
SENSOR) Detects output shaft
(countershaft) speed sensor
signalsWith ignition switch ON (II): pulses
With vehicle moving: about 5.0 V (pulses)
44 BRN/YEL LG2 (LOGIC GROUND) Ground circuit for ECM/ PCMLess than 1.0 V at all times
Terminal side of female terminals
08/08/21 14:13:36 61SNR030_110_0032
ProCarManuals.com
DYNOMITE -2009-






VTC System
VTEC System
K20Z2 engine
K20Z3 engine
11-38
Fuel and Emissions Systems
System Description (cont’d)
MAXIMUM VTC ADVANCE 25 °
TDC
EX IN 1IN 2
EX IN 2IN 1
MAXIMUM VTC ADVANCE 25 °
SHORT OVERLAP
LONG OVERLAP
LOW SPEED VALVE TIMING HIGH SPEED VALVE TIMING
EX IN EXIN
IN (LOW LIFT)
LOW SPEED VALVE TIMING HIGH SPEED VALVE TIMING
EX IN EX IN
 The VTC system makes continuous intake valve timing changes based on operating conditions.
 Intake valve timing is optimized to allow the engine to produce maximum power.
 Cam angle is advanced to obtain the EGR effect and reduce pumping loss. The intake valve is closed quickly to
reduce the entry of the air/fuel mixture into the intake port and improve the charging effect.
 The system reduces the cam advance at idle, stabilizes combustion, and reduces engine speed.
 If a malfunction occurs, the VTC system control is disabled and the valve timing is fixed at the fully retarded position.
 The VTEC system changes the cam profile to correspond to the engine speed. It maximizes torque at low engine speed and output at high engine speed.
 The low lift cam is used at low engine speeds, and the high lift cam is used at high engine speeds.
08/08/21 14:13:40 61SNR030_110_0038
ProCarManuals.com
DYNOMITE -2009-

Evaporative Emission (EVAP) Control
System Monitor and Readiness CodeAir Fuel Ratio (A/F) Sensor Monitor and
Readiness Code
Enable Criteria
Procedure Enable Criteria
Procedure
11-70Fuel and Emissions Systems
How to Set Readiness Codes (cont’d)
NOTE: All readiness codes are cleared when the battery
is disconnected, if the DTCs have been cleared, or if the
ECM/PCM is reset with the HDS.
 Battery voltage is more than 10.5 V.
 Engine at idle.
 ECT SENSOR 1 and ECT SENSOR 2 between 80 °C (176 °F) and 100 °C (212 °F).
 MAP SENSOR less than 46.6 kPa (350 mmHg, 14 in.Hg).
 Vehicle speed (VSS) 0 km/h (0 mph).
 IAT SENSOR between 0 °C (32 °F) and 100 °C (212 °F).
1. Connect the HDS to the DLC.
2. Start the engine.
3. Select EVAP TEST in the INSPECTION MENU with the HDS, then select the FUNCTION TEST in the
EVAP TEST MENU.
 If the result is normal, readiness is complete.
 If the result is not normal, go to the next step.
4. Check for a Temporary DTC. If there is no DTC, one or more of the enable criteria were probably not
met; repeat the procedure. NOTE:
 Do not turn the ignition switch to LOCK (0) or ACC (I) during the procedure.
 All readiness codes are cleared when the battery is disconnected, if the DTCs have been cleared, or if the
ECM/PCM is reset with the HDS.
ECT SENSOR 1 at 60 °C (140 °F) or more. 1. Start the engine.
2. Test-drive the vehicle under stop-and-go conditions with short periods of steady cruise. During the
drive, decelerate (with the throttle fully closed) for
5 seconds. After about 5.6 km (3.5 miles), the
readiness code should switch from incomplete to
complete.
3. Check the readiness codes screen for the air fuel ratio (A/F) sensor in the DTCs MENU with the HDS.
 If the screen shows complete, readiness is complete.
 If the screen shows not complete, go to the next step.
4. Check for a Temporary DTC. If there is no DTC, the enable criteria was probably not met. Select the
DATA LIST MENU. Check the ECT SENSOR 1 in the
ALL DATA LIST with the HDS. If the ECT SENSOR 1
is less than 60 °C (140 °F), run the engine until it is
more than 60 °C (140 °F), then repeat the procedure.
08/08/21 14:15:32 61SNR030_110_0070
ProCarManuals.com
DYNOMITE -2009-

µµ
Air Fuel Ratio (A/F) Sensor Heater Monitor
Readiness Code
Misfire Monitor and Readiness Code
Fuel System Monitor and Readiness Code
Comprehensive Component Monitor and
Readiness CodeEGR Monitor and Readiness Code
Procedure
Enable Criteria
Procedure
11-71
NOTE: All readiness codes are cleared when the battery
is disconnected, if the DTCs have been cleared, or if the
ECM/PCM is reset with the HDS.
1. Start the engine, and let it idle for 1 minute. The readiness code should switch from incomplete to
complete.
2. If the readiness code is still not set to complete, check for a Temporary DTC. If there is no DTC,
repeat the procedure.
 This readiness code is always set to available because misfiring is continuously monitored.
 Monitoring pauses, and the misfire counter resets, if the vehicle is driven over a rough road.
 Monitoring also pauses, and the misfire counter holds at its current value, if the throttle position
changes more than a predetermined value, or if
driving conditions fall outside the range of any
related enable criteria.
 This readiness code is always set to available because the fuel system is continuously monitored
during closed loop operation.
 Monitoring pauses when the catalytic converter, EVAP control system, and A/F sensor monitors are
active.
 Monitoring also pauses when any related enable criteria are not being met. Monitoring resumes when
the enable criteria is again being met.
This readiness code is always set to available because
the comprehensive component monitor is continuously
running when ever the engine is cranking or running. NOTE:
 Do not turn the ignition switch to LOCK (0) or ACC (I) during the procedure.
 All readiness codes are cleared when the battery is disconnected, if the DTCs have been cleared, or if the
ECM/PCM is reset with the HDS.
ECT SENSOR 1 at 80 °C (176 °F) or more. 1. Connect the HDS to the DLC.
2. Start the engine.
3. Drive at a steady speed with the A/T in D position or M/T in 4th gear, at 80 100 km/h (50 62 mph) or
above for more than 10 seconds.
4. With the A/T in D position or M/T in 4th gear, decelerate from 100 km/h (62 mph) or above by
completely releasing the throttle for at least
5 seconds. If the engine is stopped during this
procedure, go to step 3 and do the procedure again.
5. Check the OBD status screen for DTC P0401 in the DTC’s MENU with the HDS.
 If it is PASSED, readiness is complete.
 If it is not PASSED, go to step 3 and retest.
08/08/21 14:15:32 61SNR030_110_0071
ProCarManuals.com
DYNOMITE -2009-

(#' 
)µ
µ
µ
µ
µ
µ
DTC P0300:
DTC P0301:
DTC P0302:
DTC P0303:
DTC P0304:
Special Tools Required YES
NO
YES
NO
YES
NO
11-115
Random Misfire and Any
Combination of the Following:
No. 1 Cylinder Misfire Detected
No. 2 Cylinder Misfire Detected
No. 3 Cylinder Misfire Detected
No. 4 Cylinder Misfire Detected
 Pressure gauge adapter 07NAJ-P07010A
 A/T low pressure gauge w/panel 07406-0070301
 A/T pressure hose 07406-0020201
 A/T pressure hose, 2,210 mm 07MAJ-PY4011A
 A/T pressure hose, adapter 07MAJ-PY40120
 Oil pressure hose 07ZAJ-S5AA200
NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
 If the misfire is frequent enough to trigger detection of increased emissions during two consecutive
driving cycles, the MIL will come on, and DTC P0300
(and some of the combination of P0301 thr ough
P0304) will be stored.
 If the misfire is frequent enough to damage the catalyst, the MIL will blink whenever the misfire
occurs, and DTC P0300 (and some of the combination
of P0301 through P0304) will be stored. When the
misfire stops, the MIL will remain on.
 If any of the DTCs listed below are indicated at the same time as the random misfire DTCs, troubleshoot
those DTCs first, then recheck for random misfire
DTCs:
P0101, P0102, P0103: Mass air flow (MAF) sensor
P0107, P0108: Manifold absolute pressure (MAP)
sensor
P0171, P0172: Fuel system
P0335, P0339: Crankshaft position (CKP) sensor
P0365, P0369: Camshaft position (CMP) sensor B
P0401 , P0404 , P0416 , P2413 : Exhaust gas
recirculation (EGR) system
P0506, P0507: Idle control system
P2646, P2647, P2648, P2649: VTEC system : K20Z2 engine 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and let it idle without load (A/T in
P or N, M/T in neutral).
4. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 5. If
the screen indicates EXECUTING, keep idling until
a result comes on. If the screen indicates OUT OF
CONDITION, wait for several minutes, then recheck.
5. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 9.
Go to step 6.
6. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
 ENGINE S PEED
 VSS
 REL TP SENSOR
 CLV (calculated load value)
 APP SENSOR
7. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Go to step 9.
If the screen indicates PASSED, go to step 8. If
the screen indicates EXECUTING, keep driving until
a result comes on. if the screen indicates OUT OF
CONDITION, go to step 6 and recheck.
(cont’d)
Does t he scr een i nd i cat e F AILE D?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Does t he scr een i nd i cat e F AILE D?
08/08/21 14:17:24 61SNR030_110_0115
ProCarManuals.com
DYNOMITE -2009-

(#' 
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
DTC P050A:
11-13511-135
8. Check for damage on the CMP sensor B pulser
plate (see page 6-41).
Replace the CMP sensor B pulser plate
(see page 6-41), then go to step 11.
Go to step 9.
9. Turn the ignition switch to LOCK (0).
10. Replace CMP sensor B (see page 11-222).
11. Turn the ignition switch to ON (II).
12. Reset the ECM/PCM with the HDS.
13. Do the ECM/PCM idle learn procedure (see page 11-310).
14. Start the engine, and let it idle for 10 seconds.
15. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at CMP sensor B and the ECM/PCM, then
go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Check for Temporary DTCs or DTCs with the HDS.
Go to the indicated DTC’s troubleshooting.
Go to step 3.
3. Check for poor connections or a blockage at the intake air duct.
Go to step 4.
Reconnect or repair the intake air duct, then
go to step 20.
4. Check for damage to the air cleaner housing.
Go to step 5.
Replace the air cleaner housing (see page
11-345), then go to step 20.
5. Check for dirt or debris in the air cleaner element.
Replace the air cleaner element or remove
debris (see page 11-346), then go to step 20.
Go to step 6.
(cont’d)Cold Start Idle Air Control
System Performance Problem
Is the pulser plate damaged?
I s DT C P0369 i nd i cat ed ? Ar e any T empor ar y DT Cs or DT Cs ot her t han
P05 0A i nd i cat ed ?
Is it OK ?Is it OK ?Is it dirty?
08/08/21 14:18:56 61SNR030_110_0135
ProCarManuals.com
DYNOMITE -2009-

(#' 
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
DTC P050B:
11-13711-137
20. Turn the ignition switch to ON (II).
21. Reset the ECM/PCM with the HDS.
22. Do the ECM/PCM idle learn procedure (see page
11-310).
23. Let the engine cool until the value of ECT SENSOR 1 is 50 °C (122 °F) or less.
24. Start the engine, and let it idle for 10 seconds or more.
25. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body, the MAF sensor/IAT
sensor, and the ECM/PCM, then go to step 1.
Go to step 26.
26. Monitor the OBD STATUS for DTC P050A in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 25,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the throttle body,
the MAF sensor/IAT sensor, and the ECM/PCM,
then go to step 1. If the screen indicates
EXECUTING, keep idling until a result comes on. If
the screen indicates OUT OF CONDITION, go to
step 23. NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Check for Temporary DTCs or DTCs with the HDS.
Go to the indicated DTC’s troubleshooting.
Go to step 3.
3. Check for poor connections or a blockage at the intake air duct.
Go to step 4.
Reconnect or repair the intake air duct, then
go to step 25.
4. Check for damage to the air cleaner housing.
Go to step 5.
Replace the air cleaner housing (see page
11-345), then go to step 25.
5. Check for dirt or debris in the air cleaner element.
Replace the air cleaner element or remove
debris (see page 11-346), then go to step 25.
Go to step 6.
(cont’d)Cold Start Ignition Timing
Control System Performance Problem
Is DT C P050A ind icated ?
Does t he scr een i nd i cat e PASSE D? Ar e any T empor ar y DT Cs or DT Cs ot her t han
P05 0B i nd i cat ed ?
Is it OK ?Is it OK ?Is it dirty?
08/08/21 14:18:56 61SNR030_110_0137
ProCarManuals.com
DYNOMITE -2009-