2005 YAMAHA YD110 clutch

Spark plug :
Type/Manufacture P-RA7HC (Champion)
Spark plug gap 0.9 mm (-0.2mm)
Clutch type :Wet, multiple-disk
Transmission :
Primary reduction systemSpur gear
Primary reduction ratio3.722 (67/18)
Secondary reduction systemChain drive
Secondary reduction ratio3.143 (44/14)
Transmission type Constant mesh 4
speed
OperationLeft foot operation
Gear ratio 1st3.000
2nd 1.688
3rd 1.200
4th 0.875
Chassis:
Frame typeDouble Cradle
Caster angle 26.4 degTyre with Tube
Size
Front2.50 ~ 18” 4PR
Rear2.75 ~ 18” 6PR
Air pressure (cold tyre):
Single Rider
Front 25 psi (1.75 Kgf/cm²)
Rear 32 psi (2.25 Kgf/cm²)
With Pillion and rider
Front 25 psi (1.75 Kgf/cm²)
Rear 32 psi (2.25 Kgf/cm²)
8.3
SPECIFICATIONSfo'ks"k fooj.k
pg56_96.pmd2/25/2005, 9:59 AM 90

WARRANTY
9.6
okjaVh
The claim for exchange or repair of part (s) shall be considered only when:ikVZl d¨ cnyus vFkok budh fjis;j djus ds Dyse ij rHkh fopkj fd;k tk,xk tc %1. Customer ensures that immediately upon discovery of the defect he
approaches the nearest YMI Authorised Dealership with the affected
Motorcycle.
The expenses if any, to bring the Motorcycle to the YMI Authorised
Dealership shall be borne by the customer.
miHkksDrk ;g vk'oklu nsrk gS fd n¨"k dk irk yxus ds rqqjUr ckn og e¨VjlkbZfdy
ds lkFk utnhd ds okbZñ,eñvkbZñ Mhyj ds ikl igq¡p tk,xkA
e¨VjlkbZfdy dks vf/kÎÑr Mhyj ds ikl ys tkus dk fdlh rjg dk [kpZ] miHkksDrk
}kjk Lo;a lgu fd;k tk,xkA
2. Customer produces the Owner’s Manual in original to enable the YMI
Dealer to verify the Motorcycle details and servicing details.
eksVjlkbZfdy v©j mldh *l£o¯lx^ dh foLr r tkudkjh nsus ds fy, miHkksDrk dks
okbZñ,eñvkbZñ Mhyj d¨ vksulZ eSuqvy dh ewy izrh çLrqr djuh gksxhA
THIS WARRANTY IS NOT APPLICABLE TO;g *okjaVh^ mu ifjfLFkfr;ksa esa vuqdwy ugh jgsaxh tSls %1. Normal maintenance operations such as Engine tune-up, Decarbonising,
Fuel System Cleaning, Wheels, Brakes and Clutch adjustments as
well as any other normal adjustment.
;g okjaVh dojst dsoy rHkh ykxw gksxk tc eksVjlkbZfdy dks vf/kÑr Mhyj
}kjk lHkh eq¶r l£ol] cksul Ýh l£ol v©j isM l£ol çLrkfod l£ol varjky
esa djokbZ xbZ gks tks fd bl iqfLrdk ds i "B
10-39 ls 10-41 esa fn;k x;k
gS rFkk dsoy okbZñ,eñvkbZñ ds vf/kÑr&ikVZl~ o ;kekY;wc dk ç;ksx fd;k x;k
gksA ÑI;k ;g lqfuf'pr djsa fd çR;sd l£ol] fiNyh l£ol dk
60 fnu ds
varjky ;k çLrkfod le;kuqlkj ;k tks Hkh igys gks djokuh pkfg,A
okjaVh dh oS/krk
pg97_103.pmd2/25/2005, 9:59 AM 100

1- lkekU; ejEer ds dk;Z] tSls fd batu dh V~;w¯ux] fMdkcksZukb¯tx] b±/ku dh lQkbZ&ç.kkyh] ifg;¨a]czsdksa v©j Dyp dh
,MtLVesaV ds lkFk&lkFk dksbZ nwljh lk/kkj.k ,MtLVesaVA2. Normal replacement of service wear and tear items, i.e., Brake Shoes, Fasteners/Shims/Washers, Gaskets
and Rubber or Plastic Components, Cable and Electrical Items like Bulbs, Drive Chain, Sprocket, Clutch
plate, Race Bearing & Element Air Cleaner.
dk;Z ds n©jku f?kls rFkk [kjkc gq, ikVZl mnkgj.kr% czsd 'kwt+] QkLVulZ@f'kel@ok'klZ] xSldV rFkk jcM+ ;k IykfLVd
ds daiksusaV] rkjsa v©j bysDVªhdy vkbVe&tSls fd cYc] Mªkbo&psu] LçkWfdV v©j Dyp IysV~l] jsl cs;¯jx vkSj ,yhesaV ,;j
Dyhuj dks lk/kkj.kr% cny dj nsukA]
3. Part(s) of the Motorcycle that have been subjected to misuse, accident, negligent treatment or which have
been used in conjunction with parts and equipment not manufactured or recommended for use by Yamaha
Motor India Pvt. Ltd., if in the sole judgement of Yamaha Motor India Pvt. Ltd. such use prematurely affects
the performance and reliability of the motorcycle.
vf/kÎdj.k fd, gq, eksVjlkbZfdy ds ikVZl tks fd nq:i;ksx] nq?kZVuk] ykijokgh ls Bhd fd, x, vFkok ftUgs nwljs ikVZl
rFkk midj.kks ds lkFk tksM+ dj ç;ksx fd;k x;k gS ysfdu ;kekgk e¨VjlkbZfdy bafM;k çkñ fyñ çLrkfod vFkok fu£er ugh
fd;k x;k gS] ;fn ;kekgk e¨VjlkbZfdy bafM;k çkñ fyñds fuekZ.k ds varxZr vkrs gS] bl rjg ls mu vkbVedk vlkef;d
ç;ksx eksVjlkbZfdy dh dk;Zdq'kyrk v©j fo'oluh;rk dks çHkkfor djrk gSA
4. Use of non-genuine parts, non-genuine oil and lubricants.
udyh Y;qczhdsaVl] rsy rFkk udyh ikVZl dk ç;ksxA
5. Parts of the Motorcycle getting rusty due to atmospheric effects because of Industrial Pollution.
eksVjlkbZfdy ds os ikVZl tks fd v©|ksfxd çnw"k.k ds dkj.k rFkk okrkoj.k ds çHkkoksa dh otg ls tax idM+ ysrs gSA
6. Parts of Motorcycle that have been altered and modified or replaced in unauthorised manner and which in
the sole judgement of Yamaha Motor India Pvt. Ltd. affects its performance and reliability.
eksVjlkbZfdy ds os ikVZl ftUgs vukf/kÑr :i ls ifjo£rr fd;k x;k gS] lq/kkjk x;k gS vFkok cnyk x;k gS v©j tks ;kekgk
e¨VjlkbZfdy bafM;k çkñ fyñ ds lksy&fu.kZ; ds varxZr eksVjlkbZfdy dh dk;Zdq'kyrk rFkk fo'oluh;rk ij çHkko Mkyrs gSA
WARRANTY
9.7
okjaVh
pg97_103.pmd2/25/2005, 9:59 AM 101

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd2/25/2005, 10:00 AM 2

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd2/25/2005, 10:00 AM 4

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd2/25/2005, 10:00 AM 6

JOBS TO BE CARRIED OUT DURING TWELVETH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-8
DETGREEN.pmd2/25/2005, 10:00 AM 8

JOBS TO BE CARRIED OUT DURING ELEVENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignement marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-10
DETGREEN.pmd2/25/2005, 10:00 AM 10