2005 YAMAHA YD110 brake

Brake and shift pedal
Greasingczsd rFkk f'k¶V&iSMy dh xzhft+axGrease the pivoting parts.vk/kkjh; Hkkxksa dks fpduk ¼xzht+½ djsaA
Recommended lubricant
izLrkfor xzht+ %20W40 Type SG
Brake and clutch lever
Greasingczsd rFkk f'k¶V&iSMy dh xzhft+axGrease the pivoting parts.vk/kkjh; Hkkxksa dks fpduk ¼xzht+½ djsaA
Center and sidestand
GreasinglsaVj rFkk lkbM LVSaM dk xzhft+axGrease the pivoting and mating
joints.
Check to see that the center and
sidestand move up and down
smoothly.vk/kkjh; vkSj vkil esa feyus okys tksM+ksa
dks xzht+ djsaA
;g ns[kus ds fy, tk¡p djsa fd chp okyk
rFkk lkbM ds LVS.M vkjke ls Åij pys
tk,a vkSj vkjke ls gh uhps tk tk,aA
6.30
Recommended lubricant
izLrkfor xzht+ %20W40 Type SG
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
Recommended lubricant
izLrkfor xzht+
Multipurpose Grease
cgqmísf'k; xzht+
pg56_96.pmd2/25/2005, 9:59 AM 66

Front fork inspectionÝaV QksdZ dk fujh{k.k WARNINGSecurely support the Motorcycle
so there is no danger of it falling
over. psrkouhlqjf{kr rjhds ls eksVjlkbfdy dks lgkjk
nsa] ftlls blds fxjus dk [krjk u jgssA1. Visual check
Check for scratches or
damage on the inner tube and
traces if oil leakage from the
front fork.
n f"Vxr ¼us=kh;½ tk¡p %
vkxs yxs QksdZ esa ls vR;f/kd rsy
fjlko vkSj vanj dh V~;wc ij [kjksapks
rFkk blds {kfrxzLr gksus dh tk¡p
djsaA
2. Operation check
Place the Motorcycle on a level
place.
izfØ;k dh tk¡p %
eksVjlkbfdy dks ,d ysoy fd;s gq,
¼likV½ LFkku ij [kM+k djsaA
a. Hold the Motorcycle in an
upright position and apply the
front brake.
eksVjlkbfdy dks lh/kk Åij mBkdj
j[ksa vkSj vxyh czsd dk mi;ksx djsaA
b. Push down hard on the
handlebars several times and
check if the fork bounds
smoothly.
gSafMyckjksa dk dbZ ckj tksj ls uhps
dh vksj nck,a vkSj bl ckr dh tk¡p
djsa fd D;k QksdZ vkjke ls ^mNky*
ys ysrk gSA
6.31

WARNING
If the center and/or sidestand does
not move smoothly, consult a YMI
dealer. psrkouh;fn eksVjlkbfdy ds chp okyk rFkk
lkbM dk LVS.M vkjke ls ¼fcuk fdlh
:dkoV½ ds dke ugha djrs gksa rks
okbZñ,eñvkbZñ Mhyj ls laidZ djsaA
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
pg56_96.pmd2/25/2005, 9:59 AM 67

1. Brake cable adjusting nut
czsd dh rkj dk ,M~t¯LVx uVA
1. Place the Motorcycle on the
centerstand.eksVjlkbfdy dks chp okys LVS.M ij
yxkdj [kM+k djsaA
2. Fully loosen the brake cable
adjusting nut at the wheel hub
and remove the cable from the
brake cam lever.
ifg, ds gc ij yxs czsd dh rkj ds
,M~t¯LVx uV dks iwjk [kksy ysa vkSj
rkj ¼dscy½ dks cszd ds dSe yhoj esa
ls ckgj fudky ysaA
Front wheel removalvxys ifg, dks gVkuk WARNING It is advisable to have a YMI
dealer service the wheel.
 Securely support the
Motorcycle so there is no
danger of it falling over. psrkouh
mi;qDr ;gh gS fd okbZñ,eñvkbZñ Mhyj
ls gh ifg, dh ^l£ol* djkbZ tk,A

eksVjlkbfdy dks lqjf{kjr rjhds ls
lgkjk nsa rkfd bls iyV dj fxjus
dk [krjk u jgsA
6.40
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
1
pg56_96.pmd2/25/2005, 9:59 AM 76

1. Stopper
LVkWij
Front wheel installationvxys ifg, dks yxkukWhen installing the front wheel,
reverse the removal procedure.tc vxys ifg, dks yxkuk gks rks ifg;k
gVkus dh ^izfØ;k* dks myV nsaA
fuEufyf[kr rF;ksa ij /;ku nsaA1. Make sure the slot in the brake
shoe plate fits over the stopper
on the front fork outer tube.
;g lqfuf'pr dj ysa fd czsd dh
'kw&IysV esa cuk gqvk LykWV] vxys
QksdZ dh ckgjh V~; c ij yxs LVkWij
ds lkFk ^fQV* ¼Bhd rjg ls cSB tk,½
gks tk,A
1. Cotter pin
dkWij fiu
2. Axle nut
,Dly uV
5. Remove the cotter pin and axle
nut.
dkWVj fiu rFkk ,Dly uV dks [kkssydj
ckgj fudky ysaA
6. Remove the wheel axle. Make
sure the Motorcycle is properly
supported.
ifg, ds ,Dly dks ckgj fudky ysaA
lqfuf'pr djsa fd eksVjlkbZfdy dks
mfpr lgkjk feyrk jgsA
1. Clip
fDyi
2. Speedometer cable
LihM+¨ehVj dscy
4. Remove the speedometer
cable from the front wheel side.
First remove the clip and then
pull the cable out.
LihM+¨ehVj dscy d¨ vxys ifg;s
ls gVk;saA igys fDyi d¨ gVk;sa
v©j mlds ckn dscy d¨ [khpsaA
6.41
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
2
1
2
1
1
pg56_96.pmd2/25/2005, 9:59 AM 77

Rear wheel removalfiNys ifg, dks gVkuk
WARNING
 It is advisable to service the
wheel by YMI dealer.
 Securely support the
Motorcycle so there is no
danger of it falling over. psrkouh
mi;qDr ;gh gS fd ifg, dh ^l£ol*
okbZñ,eñvkbZñ Mhyj ls gh djkbZ tk,A

eksVjlkbfdy dk lqjf{kr rjhds ls
lgkjk nsdj [kM+k djsaA rkfd bls
iyV dj fxjus dk [krjk u jgsA
Axle nut torque
,Dly ds uV dk VkdZ %
33 ft.-lb (4.55 m-kg)
2. Make sure the axle nut is
properly torqued and a new
cotter pin is installed.
;g lqfuf'pr djsa fd ,Dly ds uV
dks lgh rjhds ls dlk
gqvk gks vkSj
ml ij u;k dkWVj fiu yxk gksA
WARNINGAlways use a new cotter pin. psrkouhges'kk dkWVj fiu dk iz;ksx djsaA3. Adjust the free play in the brake
lever.
czsd yhoj ds Ýh&Iys dks ,M~tLV
djsaA
1. Nut
uV
2. Cotter pin
dkWVj fiu
3. Tension bar
Vsa'ku ckj
1. Place the Motorcycle on the
centerstand.
eksVjlkbfdy dks chp ds LVS.M ij
[kM+k djsaA
2. Remove the cotter pin and nut.
Then remove the tension bar
from the brake shoes plate.
dkWVj fiu vkSj uV dks gVk nsaA mlds
ckn 'kw&IysV esa ls ^Vsa'ku&ckj* dks
ckgj fudky ysaA
6.42
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
2
1
3
pg56_96.pmd2/25/2005, 9:59 AM 78

1. Rear axle
fiNyk ,Dly
4. Remove the axle nut cotter pin
and the axle nut.
,Dly ds uV vkSj ,Dly&uV ds
dkWVj&fiu dks [kksydj ckgj fudky
ysaA
5. Pull out the rear axle.
fiNys ,Dly dks ckgj dh rjQ [khapsA
6. Remove the wheel assembly.
ifg, dh vlsEcyh dks ckgj fudky
ysaA
1. Axle nut
,Dly&uV
2. Cotter pin
dkWVj fiu
3. Brake rod
czsd&jkWM ¼czsd dh NM+½
4. Brake adjusting nut
czsd dk ,M~t¯LVx&uV
3. Remove the brake adjusting
nut and brake rod from the
brake cam lever.
czsd ds dSe&yhoj esa ls czsd dk
,M~t¯LVx uV vkSj czsd dh NM+ ¼jkWM½
dks ckgj fudky ysaA
ALWAYS USE YMI GENUINE SPARE PARTSges'kk ^;kekgk* ds vlyh iqtkZsa dk iz;ksx djsaA
6.43
PERIODIC MAINTENANCE AND MINOR REPAIR
lkef;d j[kj[kko rFkk ekewyh ejEer
1
2
3
4
pg56_96.pmd2/25/2005, 9:59 AM 79

Rear wheel installationfiNys ifg, dks yxkuk1. Install the rear wheel and the
axle.
fiNys ifg, vkSj ,Dly dks yxk;saA
2. Install the axle nut.
,Dly ds uV dks yxk;saA
3. Insert the brake rod into the
brake cam lever and install the
brake free play adjusting nut.
czsd dh NM+ dks cszd ds dSe yhoj esa
cSBk,a ¼Mkysa½ vkSj ^czsd Ýh Iys ,M~t¯LVx
uV dks* ogka yxk nsaA
4. Install the tension bar on to the
brake shoe plate and tighten
the tension bar nut to the
specified tightening torque.
czsd 'kw IysV ij Vsa'ku ckWj dks yxk;sa
rFkk dk Vsa'ku ckWj uV dks fu£n"V
VkdZ ij dl nsaA
5. Take the Motorcycle off the
centerstand.
eksVjlkbfdy dks lsaVj LVS.M ls uhps
mrkj nsaA
Specified torque
fu£n"V VkdZ %
Tension bar nut
Vsa'ku&ckj dk uV %
14 ft-lb (1.9 mkg)
Axle nut
,Dly uV %
65 ft-lb (9.05 mkg)
6. Tighten the axle nut to the
specified tightening torque.
Then install a new cotter pin.
,Dly ds uV dks fu£n"V VkdZ rd ys
tkdj vPNh rjg ls dl nsaA
rRi'pkr~ u;k dkWVj fiu yxk,aA
WARNINGAlways use a new cotter pin. psrkouhges'kk u;s dkWVj&fiu dk iz;ksx djsaA7. Adjust the rear brake pedal free
play. (See page 6-23)
fiNyh czsd&iSMy dh Lora=k ¼Ýh½ Iys
dks ,M~tLV djsaA
¼i "B la[;k
6-23
ns[ksaa½
WARNINGCheck the operation of the brake
light after adjusting the rear
brake. psrkouhfiNyh czsd dks ,M~tLV djus ds ckn
czsd ykbV dh dk;Z&iz.kkyh dh tk¡p djsaA
6.44
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
pg56_96.pmd2/25/2005, 9:59 AM 80

1. Before cleaning the Motorcycle :
eksVjlkbfdy dh lQkbZ djus ls
igys %
a. Block off the end of the exhaust
pipe to prevent water entry; a
plastic bag and string rubber
band may be used.
,XtkWLV ikbZi ¼fudkl&ikbi½ ls ikuh
ds izos'k dks jksdus ds fy, ikbi ds
,d fljs dks IykfLVd cSx vkSj jcj
cSaM dk iz;ksx djds] can fd;k tk
ldrk gSA
b. Make sure the spark plug and all
filler caps are properly installed.
lqfuf'pr djssa fd LikWdZ Iyx vkSj
lHkh fQYyj&dSSIl Bhd rjg ls yxk,
x;s gksaA
2. If the engine case is excessively
greasy, apply degreaser with a
paint brush. Do not apply
degreaser to the chain,
sprockets, or wheel axles.
;fn batu dk dsl vR;kf/kd :i ls
fpduk gS rks isaV czq'k dh lgk;rk ls
bl ij ^fpdukbZ vojks/kd* yxk,aA
psu] LizkWdsV~l vFkok ifg, ds ,Dlyksa
ij fM&xzhlj dk mi;ksx u djsaA
A. CLEANING
lQkbZ
Frequent, thorough cleaning of your
Motorcycle will not only enhance its
appearance but will improve its
general performance and extend the
useful life of many components.tYnh&tYnh] iwjh rjg lQkbZ u dsoy
vkidh eksVjlkbfdy dks ns[kus esa vPNk
cukrh gS cfYd bldh lk/kkj.k dk;Z{kerk
esa lq/kkj ykrh gS vkSj blls cgqr ls iqtsZ
ds dk;Z&dky esa o f) gksrh gS CAUTION :
 Improper cleaning can damage
the cowlings, panels and other
plastic parts. Use only a soft,
clean cloth or sponge with mild
detergent and water to clean
plastic.
 Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
lko/kkuh %
xyr rjhds ls dh xbZ lQkbZ ls
eksVjlkbfdy ds dkůyx] iSuy rFkk
vU; IykWfLVd ds iqtsZ [kjkc gks ldrs
gSaA IykWfLVd ds iqtksZa dks lkQ djus
ds fy, eghu fMVtsZaV vkSj ikuh ds
lkFk dsoy lkQ] eqyk;e diM+s dk
gh iz;ksx djsaA IykfLVd ds iqtsZ
¼daiksusaV~l½ ds fy, fdlh rst
dsehdYl dk iz;ksx u djsaA

lqfuf'pr djsa fd mu diM+ksa vFkok
Liat ds iz;ksx ls cpk tk, tks
'kfDr'kkyh vFkok ,cjsflo lQkbZ
mRiknksa] nzkod] vFkok fFkuj] b±/ku]
¼xSl½ tax izfrjks/kdksa vFkok
tax&fueZwydksa] cszd ds b±/ku] 'khr
fojks/kh ¼,aVh&Ýht½ vFkok bysDVªksykbV
ds laidZ esa vk tkrs gSaA
7.1
CLEANING AND STORAGElQkbZ rFkk HkaMkj.k
pg56_96.pmd2/25/2005, 9:59 AM 84