2005 YAMAHA VX110 check engine

4-1
EFUELFUEL TANK AND FUEL PUMP MODULE
FUEL TANK AND FUEL PUMP MODULE
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step Procedure/Part name Q’ty Service points
FUEL TANK REMOVAL
Follow the left “Step” for removal.
Storage compartment panel Refer to “FRONT HOOD” in Chapter 8.
Ventilation hose From ventilation fitting
Engine unit Refer to “ENGINE UNIT” in Chapter 5.
NOTE:
When removing the pump module only, it is
not necessary to remove the engine unit.
1 Fuel tank breather hose 1
2 Check valve 1
NOTE:
Make sure the arrow direction pointed
toward fuel tank.
7
10
11 3
2
1
18
17121315
16
14
12 6 5
4 8
9
2nd 6.4 N • m (0.64 kgf  m, 4.6 ft  Ib) 1st 3.2 N  m (0.32 kgf  m, 2.3 ft  Ib)
3.7 N  m (0.37 kgf  m, 2.7 ft  Ib)
5.9 N  m (0.59 kgf  m, 4.3 ft  Ib)
ProCarManuals.com

4-14
EFUEL
THROTTLE BODY ASSEMBLY AND INTAKE
MANIFOLD
Fuel hose installation (replacing with new
fuel hose)
1. Install:
Fuel hose 1

NOTE:
To install the fuel hose, be sure to align the
white mark a
of the fuel hose with the
checker tab 2
of the quick connector.
When replacing the fuel hose with a new
one, a checker tab 2
that has half engage-
ment prevention is attached to the quick con-
nector of the hose. If the quick connector is
completely installed to the fuel pipe, it is
removable.
2
1a
2
Fuel hose connection
1. Apply a thin coat of engine oil to the con-
tact surfaces of the fuel pipe.
2. Insert the quick connector into the fuel
pipe until you hear a “click.”
3. To check the connection of the quick con-
nector, push and pull on the quick connec-
tor several times until there is free play of
2–3 mm (0.08–0.12 in).
NOTE:
If free is not obtained, disconnect the fuel hose
and check the O-ring for damage and that it is
properly installed.
ProCarManuals.com

5-5
EPOWRENGINE UNIT
5. Measure:
Compression pressure
Out of specification →
Refer to steps (b)
and (c).
6. Install:
Spark plug
Minimum compression pressure
(reference data):
1,150 kPa
(11.5 kgf/cm
2, 164 psi)
Measurement steps:
a. With the throttle wide open, crank the
engine until the reading on the compres-
sion gauge stabilizes.
NOTE:
The difference in compression pressure
between cylinders should not exceed 100
kPa (1 kgf/cm2, 14 psi).
b. If the compression pressure is extremely
high, check the cylinder head, valve sur-
faces and piston crown for carbon depos-
its.
Carbon deposits →
Eliminate.
c. If the compression pressure is below the
minimum specification, squirt a few drops
of oil into the cylinder and measure
again.
Refer to the following table.
Compression pressure
(with oil applied into the cylinder)
Reading Diagnosis
Higher than
without oilPiston ring wear,
piston wear or
damage
→ Repair.
Same as without
oilValves, cylinder
head gasket or pis-
ton possibly defec-
tive
→ Repair.
T R..
Spark plug:
13 N  m (1.3 kgf  m, 9.4 ft  lb)
ProCarManuals.com

E
–+ELEC
INDICATION SYSTEM .................................................................................. 7-48
WIRING DIAGRAM ................................................................................. 7-48
FUSE ....................................................................................................... 7-50
BATTERY ................................................................................................ 7-50
MAIN AND FUEL PUMP RELAY............................................................. 7-50
ECM......................................................................................................... 7-50
ENGINE TEMPERATURE SENSOR ...................................................... 7-50
THERMOSWITCH (ENGINE).................................................................. 7-50
THERMOSWITCH (EXHAUST) .............................................................. 7-50
REMOTE CONTROL UNIT (DELUXE MODEL ONLY) ........................... 7-50
BUZZER .................................................................................................. 7-50
OIL PRESSURE SWITCH ....................................................................... 7-51
MULTIFUNCTION METER...................................................................... 7-51
Multifunction meter ............................................................................ 7-51
MULTIFUNCTION METER REMOVAL ................................................... 7-51
Display function (Sport model only) .................................................. 7-52
Display function (Deluxe model only) ................................................ 7-53
Speedometer display ........................................................................ 7-54
Tachometer display ........................................................................... 7-55
Hour meter display ............................................................................ 7-55
Voltage meter display........................................................................ 7-55
Low oil pressure warning indicator .................................................... 7-55
Fuel level meter display and fuel warning indicator .......................... 7-55
Overheat warning indicator ............................................................... 7-56
Check engine warning indicator ........................................................ 7-56
Diagnostic display ............................................................................. 7-57
REMOTE CONTROL SYSTEM (DELUXE MODEL ONLY) .......................... 7-58
WIRING DIAGRAM ................................................................................. 7-58
REMOTE CONTROL SYSTEM ............................................................... 7-59
Yamaha Security System indicator ................................................... 7-59
Low-rpm mode indicator.................................................................... 7-59
Checking the remote control transmitter ........................................... 7-60
Transmitter registration ..................................................................... 7-62
Replacing of the transmitter battery .................................................. 7-63
ProCarManuals.com

7-10
E
–+ELECELECTRICAL ANALYSIS
Low resistance measurement
NOTE:
When measuring a resistance of 10 Ω
or less
using a digital tester, the correct measure-
ment cannot be obtained because of the
tester’s internal resistance.
To obtain the correct value, subtract the
internal resistance from the displayed mea-
surement.
The internal resistance of the tester can be
obtained by connecting both of its terminals.
Correct value =
Displayed measurement –
Internal resistance
Peak voltage measurement
NOTE:
When checking the condition of the ignition
system it is vital to know the peak voltage.
Cranking speed is dependant on many fac-
tors (e.g., fouled or weak spark plugs, a
weak battery). If one of these is defective,
the peak voltage will be lower than specifica-
tion.
If the peak voltage measurement is not
within specification the engine will not oper-
ate properly.
A low peak voltage will also cause compo-
nents to prematurely wear.
ProCarManuals.com

7-11
E
–+ELECELECTRICAL ANALYSIS
Peak voltage adapter
NOTE:
Throughout this chapter the part numbers of
the specified peak voltage adapters have
been omitted. Refer to the following part
numbers.
The peak voltage adapter should be used
with a digital tester.
When measuring the peak voltage, connect
the peak voltage adapter to the digital circuit
tester and switch the selector to the DC volt-
age mode.
NOTE:
Make sure that the adapter leads are prop-
erly installed in the digital circuit tester.
Make sure that the positive pin (the “+” mark
facing up as shown) on the adapter is
installed into the positive terminal of the
tester.
The test harness is needed for the following
tests.
È Voltage measurement
É Peak voltage measurement
Test harness
NOTE:
If the lighting coil and pickup coil(s) are mea-
sured unloaded, disconnect the test harness
on the output side coupler.
Peak voltage adapter:
YU-39991
Peak voltage adapter B:
90890-03172
Checking steps:
Disconnect the coupler connections.
Connect the test harness between the
couplers.
Connect the tester terminals to the termi-
nals which are being checked.
Run the engine and observe the mea-
surement.È
É
ProCarManuals.com

7-14
E
–+ELECIGNITION SYSTEM
IGNITION SPARK
WARNING
When checking the spark gap, do not
touch any of the connections of the spark
checker/ignition tester lead wires.
When performing the spark gap test, take
special care not to let sparks leak out of
the removed spark plug cap.
When performing the spark gap check,
keep flammable gas or liquids away,
since this test can produce sparks.
1. Check:
Ignition spark
Weak →
Check the ECM output peak
voltage.
Check the ignition coil for resistance.
Checking steps:
Connect the spark plug cap to the special
service tool.
Spark checker:
YM-34487
Ignition tester:
90890-06754
Crank the engine and observe the igni-
tion system spark through the discharge
window.
OK
ProCarManuals.com

7-15
E
–+ELECIGNITION SYSTEM
IGNITION SYSTEM PEAK VOLTAGE
WARNING
When checking the electrical components,
do not touch any of the connections of the
digital tester lead wires.
NOTE:
If there is no spark, or the spark is weak,
continue with the ignition system test.
If a good spark is obtained, the problem is
not with the ignition system, but possibly with
the spark plug(s) or another component.
1. Measure:
ECM output peak voltage
Below specification →
Measure the
pickup coil output peak voltage.
NOTE:
When measuring the ECM output peak volt-
age while cranking the engine, disconnect
the ignition coil couplers for all cylinders
except for the cylinder being measured.
To crank the engine, connect the engine
shut-off cord (lanyard) to the engine shut-off
switch, and then press the start switch.
Test harness (2 pins):
New: YB-06867
Current: YB-06767
Test harness FWY-2 (2 pins):
New: 90890-06867
Current: 90890-06767
ECM output peak voltage:
Black/red (B/R) –
Red/yellow (R/Y)
Black/white (B/W) –
Red/yellow (R/Y)
Black/yellow (B/Y) –
Red/yellow (R/Y)
Black/green (B/G) –
Red/yellow (R/Y)
r/minLoaded
Cranking 2,000 3,500
V 90 130 140
ProCarManuals.com