2005 YAMAHA VX110 air filter

2-10
ESPECTIGHTENING TORQUES
TIGHTENING TORQUES
SPECIFIED TORQUES
Part to tightenedPart
nameThread
sizeQ’tyTightening torque
RemarksRefer to
page
Nmkgfmftlb
Fuel system
Retainer/fuel pump
module1st
Nut—93.20.322.3
4-1
2nd 6.4 0.64 4.6
Fuel filler neck/rubber seal Nut—1 5.9 0.59 4.3 4-1
Fuel filter hose clamp——2 3.7 0.37 2.7 4-1
Air filter case cover Screw M52 1.2 0.12 0.9
572LT4-7
4 1.5 0.15 1.1
Air filter case Bolt M8 4 17 1.7 12 4-7
Air filter case bracket Nut—4 15 1.5 11 4-7
Air intake hose clamp——1 2.5 0.25 1.8 4-7
Throttle cable Nut—1 6.5 0.65 4.7 4-7
Accelerator position sensor Nut—2 17 1.7 12 4-7
Throttle body assembly Bolt M8 4 13 1.3 9.4 4-10
Intake manifold1st
Bolt M6 28.80.886.4
242LT4-7
2nd 18 1.8 13
Intake manifold bracket/
wiring harness bracket 11st
Bolt M8 215 1.5 11
271LT4-7
2nd 39 3.9 28
Fuel rail Bolt M8 2 13 1.3 9.4 4-10
Sensor assembly Screw M5 2 3.5 0.35 2.5 4-10
Engine
Engine unit Bolt M8 4 17 1.7 12
271LT5-1
Oil filter——1171.712
E3-17
Coupling cover Bolt M6 1 7.8 0.78 5.6
572LT5-1
Thermoswitch (exhaust) Bolt M6 2 7.6 0.76 5.5
572LT5-8
Outer exhaust joint
clamp1st
——23.40.342.5
5-8
2nd 3.4 0.34 2.5
Inner exhaust joint clamp1st
——23.40.342.5
5-8
2nd 3.4 0.34 2.5
Exhaust pipe 2
*1 1st
Bolt M10 42.0 0.2 1.4242LT5-9 2nd 15 1.5 11
3rd 39 3.9 28
Exhaust pipe end1st
Bolt M6 33.70.372.7
572LT5-10
2nd 7.6 0.76 5.5
Exhaust pipe 11st
Bolt M8 422 2.2 16
242LT5-10 2nd 22 2.2 16
3rd 35 3.5 25
Exhaust manifold1st
Bolt M8 1122 2.2 16
242LT5-11 2nd 22 2.2 16
3rd 35 3.5 25
*1: For details, refer to the tightening procedures in this manual.
ProCarManuals.com

E
INSP
ADJ
1
2
3
4
5
6
7
8
9
CHAPTER 3
PERIODIC INSPECTION AND ADJUSTMENT
MAINTENANCE INTERVAL CHART .............................................................. 3-1
PERIODIC SERVICE ....................................................................................... 3-2
CONTROL SYSTEM ................................................................................. 3-2
Steering column inspection ................................................................. 3-2
Steering cable inspection and adjustment .......................................... 3-2
Throttle cable inspection and adjustment............................................ 3-4
Shift cable inspection and adjustment (Deluxe model only)................ 3-5
Trolling speed inspection .................................................................... 3-6
FUEL SYSTEM.......................................................................................... 3-7
Fuel line inspection ............................................................................. 3-7
Water separator inspection ................................................................. 3-8
POWER UNIT............................................................................................ 3-8
Valve clearance adjustment ................................................................ 3-8
Engine oil level check........................................................................ 3-14
Engine oil change — using oil changer ............................................. 3-16
Air filter element clean....................................................................... 3-18
Spark plug inspection ........................................................................ 3-20
ELECTRICAL .......................................................................................... 3-22
Battery inspection.............................................................................. 3-22
JET PUMP UNIT ..................................................................................... 3-25
Impeller inspection ............................................................................ 3-25
Water inlet strainer inspection ........................................................... 3-25
BILGE PUMP........................................................................................... 3-26
Bilge strainer inspection .................................................................... 3-26
GENERAL ............................................................................................... 3-26
Drain plug inspection......................................................................... 3-26
Lubrication points .............................................................................. 3-26
ProCarManuals.com

3-1
E
INSP
ADJ
MAINTENANCE INTERVAL CHART
MAINTENANCE INTERVAL CHART
The following chart should be considered strictly as a guide to general maintenance intervals.
Depending on operating conditions, the intervals of maintenance should be changed.
*1: After every use
MAINTENANCE INTERVAL INITIALTHEREAFTER
EVERYPAGE
10 hours 50 hours 100 hours 100 hours 200 hours
ITEM6
months12
months12
months24
months
Spark plug Inspect, clean, adjust 3-20
Lubrication points Lubricate 3-26
Fuel system Inspect3-7
Fuel tank Inspect, clean 3-7
Trolling speed Inspect3-6
Throttle shaft Inspect—
Cooling water passages Flush *1 —
Water inlet strainer Inspect, clean —
Bilge strainer Clean3-26
Impeller Inspect3-25
Jet thrust nozzle angle Inspect, adjust 3-2
Shift cable and
mechanism
(Deluxe model only)Inspect, adjust 3-5
Throttle cable Inspect, adjust 3-4
Stern drain plugs Inspect, replace 3-26
Battery Inspect 3-22
Rubber coupling Inspect—
Engine mount Inspect5-7
Nuts and bolts Inspect—
Air filter Inspect, replace 3-18
Engine oil Replace 3-14
Engine oil filter Replace 3-16
Valve clearance Inspect, adjust 3-8
ProCarManuals.com

3-14
E
INSP
ADJ
POWER UNIT
8. Remove:
Dial gauge
Dial gauge stand
Dial gauge needle
9. Install:
All removed parts
NOTE:
For installation, reverse the removal proce-
dure.
Engine oil level check
1. Check:
Engine oil level
Checking steps:
CAUTION:
When checking the engine oil level on
water, be careful of other watercraft,
boats, swimmers, or obstacles. The
water current or wind can cause the
watercraft to move and lead to a colli-
sion.
When checking the engine oil level on
land, supply water to the cooling water
passages.
Make sure that engine has enough oil
but do not overfill. If there is too little
oil, the engine can be damaged. If there
is too much oil, the air filter can
become saturated with oil, perma-
nently damaging the filter and reduc-
ing engine performance. Follow the
checking procedure carefully.
Make sure that debris or water does
not enter the oil tank filler hole. Debris
or water in the engine oil can cause
serious engine damage.
ProCarManuals.com

3-18
E
INSP
ADJ
POWER UNIT
7. Fill:
Oil tank
(with the specified amount of the recom-
mended engine oil)
CAUTION:
When starting the engine make sure the
dipstick is securely fitted into the oil tank.
8. Install:
Oil tank filler cap
Recommended oil:
SAE 10W-30, 20W-40, 20W-50
API SE, SF, SG, SH, SJ, SL
Oil quantity:
Total amount:
4.3 L (4.5 US qt, 3.8 Imp qt)
Without oil filter replacement:
2.0 L (2.1 US qt, 1.8 Imp qt)
With oil filter replacement:
2.2 L (2.3 US qt, 1.9 Imp qt)
Air filter element clean
1. Disconnect:
Fuel hose 1

Air intake hose 2

Oil separator breather hose 3

2. Remove:
Plastic ties 4

Bolts 5

1
2 4
45 4
3
3. Remove:
Air filter case
4. Remove:
Air filter case cover
ProCarManuals.com

3-19
E
INSP
ADJ
POWER UNIT
5. Remove the air filter element and check it
for dirt and oil. Replace the air filter ele-
ment if there is any oil buildup.
CAUTION:
Do not start the engine with the air filter
case removed, otherwise the engine
could be damaged.
If cleaning the air filter element, use cold
or lukewarm water and let it air dry com-
pletely. Do not use detergent or a solvent
to clean the air filter element, or dry it with
heat or compressed air, otherwise it
could be damaged.
6. Install:
Air filter element
NOTE:
Install the air filter element with its projections
a
facing away from the projections b
on the
air filter case.
7. Install:
Air filter case cover
8. Install:
Air filter case
T R..
Air filter case cover screw (short):
1.5 N  m (0.15 kgf  m, 1.1 ft  lb)
LOCTITE 572
Air filter case cover screw (long):
1.2 N  m (0.12 kgf  m, 0.9 ft  lb)
LOCTITE 572
T R..
Air filter case:
17 N  m (1.7 kgf  m, 12 ft  lb)
a
b
ProCarManuals.com

EFUEL
1
2
3
4
5
6
7
8
9
CHAPTER 4
FUEL SYSTEM
FUEL TANK AND FUEL PUMP MODULE...................................................... 4-1
EXPLODED DIAGRAM ............................................................................. 4-1
REMOVAL AND INSTALLATION CHART ................................................ 4-1
SERVICE POINTS .................................................................................... 4-4
Fuel hose disconnection ..................................................................... 4-4
Fuel pump module removal................................................................. 4-4
Check valve inspection ....................................................................... 4-4
Fuel sender inspection ........................................................................ 4-5
Fuel tank inspection ............................................................................ 4-5
Fuel hose inspection ........................................................................... 4-5
Fuel pump filter inspection .................................................................. 4-5
Fuel pump module installation ............................................................ 4-6
Fuel hose connect ............................................................................... 4-6
FUEL INJECTION SYSTEM ............................................................................ 4-7
EXPLODED DIAGRAM ............................................................................. 4-7
REMOVAL AND INSTALLATION CHART ................................................ 4-7
THROTTLE BODY ASSEMBLY AND INTAKE MANIFOLD ........................ 4-10
EXPLODED DIAGRAM ........................................................................... 4-10
REMOVAL AND INSTALLATION CHART .............................................. 4-10
SERVICE POINTS .................................................................................. 4-12
Fuel hose clamps removal ................................................................ 4-12
Hose clamps installation ................................................................... 4-12
Fuel hose disconnection ................................................................... 4-12
Fuel line inspection ........................................................................... 4-13
Fuel hose installation (replacing with new fuel hose) ........................ 4-14
Fuel hose connection ........................................................................ 4-14
Fuel injectors inspection.................................................................... 4-15
Throttle body assembly inspection .................................................... 4-15
Accelerator position sensor inspection.............................................. 4-15
Intake assembly installation .............................................................. 4-16
Air filter case assembly installation ................................................... 4-17
Fuel pressure measurement ............................................................. 4-17
ProCarManuals.com

4-8
EFUELFUEL INJECTION SYSTEM
EXPLODED DIAGRAM
Step Procedure/Part name Q’ty Service points
10 Fuel hose 1
11 Clamp 2
12 Hose screw clamp 1
13 Screw 2
14 Screw 4
15 Air filter case cover 1
16 Air intake duct 1
17 Air intake hose 1
18 Gasket 1
19 Air filter element 1
20 Bolt 4
17 N  m (1.7 kgf  m, 12 ft  Ib)
5 × 75 mm
1.2 N  m (0.12 kgf  m, 0.9 ft  Ib)
5 × 25 mm
1.5 N  m (0.15 kgf  m, 1.1 ft  Ib)
8 × 35 mm
17 N  m (1.7 kgf  m, 12 ft  Ib)2nd 18 N  m (1.8 kgf  m, 13 ft  Ib) 1st 8.8 N  m (0.88 kgf  m, 6.4 ft  Ib)
8 × 30 mm
2nd 39 N  m (3.9 kgf  m, 28 ft  Ib) 1st 15 N  m (1.5 kgf  m, 11 ft  Ib)
8 × 20 mm
LT
242
LT
242
LT
271
LT
572
LT
LT
572
LT
22 2320 19
2118 15 1316
14 1712
17
3
2
2
25
4
6
24
24
25 8
26
27
28
29
11 10
9
2.5 N  m (0.25 kgf  m, 1.8 ft  Ib)
6.5 N  m (0.65 kgf  m, 4.7 ft  Ib)
15 N  m (1.5 kgf  m, 11 ft  Ib)
3031
30
Not reusable
ProCarManuals.com