PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
2
3
4
5
67
8
9
10
*
Tires
Check tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.
√√√√ √
11
*
Wheel bearings
Check bearing for looseness or damage.
√√√√
12
*
Swingarm
Check operation and for excessive play.
√√√√
Lubricate with molybdenum disulfide grease. Every 50000 km
13
Drive chain
Check chain slack, alignment and condition.
Adjust and lubricate chain with a special O-ring chain
lubricant thoroughly.Every 500 km and after washing the motorcycle or
riding in the rain
14
*
Steering bearings
Check bearing play and steering for roughness.
√√√√√
Lubricate with lithium-soap-based grease. Every 50000 km
15
*
Chassis fasteners
Make sure that all nuts, bolts and screws are properly
tightened.
√√√√ √
16
Sidestand
Check operation.
Lubricate.
√√√√ √
17
*
Sidestand switch
Check operation.
√√√√√ √
18
*
Front fork
Check operation and for oil leakage.
√√√√
19
*
Shock absorber assem-
bly
Check operation and shock absorber for oil leakage.
√√√√
20
*
Rear suspension relay
arm and connecting arm
pivoting points
Check operation.
√√√√
Lubricate with molybdenum disulfide grease.
√√
21
*
Carburetor
Check starter (choke) operation.
Adjust engine idling speed.
√√√√√ √
22
Engine oil
Change.
Check oil level and vehicle for oil leakage.
√√√√√ √
23
Engine oil filter element
Replace.
√√√
NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (
×
1000 km)
ANNUAL
CHECK
1 10203040
PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
1
2
3
4
5
6
7
8
9
4. If the drive chain slack is incorrect,
adjust it as follows.
EAU22960
To adjust the drive chain slack
1. Loosen the axle nut.
2. To tighten the drive chain, turn the
adjusting plate on each side of the
swingarm in direction (a). To loos-
en the drive chain, turn the adjust-
ing plate on each side of the
swingarm in direction (b), and then
push the rear wheel forward.
NOTE:
Make sure that both adjusting plates
are in the same position for proper
wheel alignment.
CAUTION:
ECA10570
Improper drive chain slack will over-
load the engine as well as other vital
parts of the motorcycle and can lead
to chain slippage or breakage. To
prevent this from occurring, keep
the drive chain slack within the
specified limits.
3. Tighten the axle nut to the speci-
fied torque.
EAU23022
Cleaning and lubricating the
drive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.
CAUTION:
ECA10581
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.
1. Clean the drive chain with kero-
sene and a small soft brush.
CAUTION:
ECA11120
To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
1. Drive chain slack
1
1. Adjusting plate
2. Stopper
3. Axle nut
Tightening torque:
Axle nut:
85 Nm (8.5 m·kgf, 61.5 ft·lbf)
1
3
2
(a)
(b)
