2005 YAMAHA TRICKER 250 check oil

PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
1
2
3
4
5
6
7
8
9
7. Install the oil filter element cover by
installing the bolts, then tightening
them to the specified torque.
8. Install the engine oil drain bolt, and
then tighten it to the specified
torque.
9. Install the oil filter element drain
bolt, and then tighten it to the spec-
ified torque.10. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler bolt.
CAUTION:

ECA11620

In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” orhigher.

Make sure that no foreign mate-
rial enters the crankcase.
11. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
12. Turn the engine off, and then
check the oil level and correct it if
necessary.
1. Oil filter element
2. O-ring
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
1
2
2

Tightening torques:
Engine oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Oil filter element drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Recommended oil:
See page 8-1.
Oil quantity:
Without oil filter element replace-
ment:
1.20 L (1.27 US qt) (1.06 Imp.qt)
With oil filter element replacement:
1.30 L (1.37 US qt) (1.14 Imp.qt)

PERIODIC MAINTENANCE AND MINOR REPAIR
6-19
2
3
4
5
67
8
9
lower the boiling point of the fluid
and may result in vapor lock.


Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.

As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.
EAU22730
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

Oil seals: Replace every two
years.

Brake hoses: Replace every four
years.
EAU22760
Drive chain slack
The drive chain slack should be
checked before each ride and adjusted
if necessary.
EAU22771
To check the drive chain slack
1. Place the motorcycle on the side-
stand.
NOTE:

When checking and adjusting the drive
chain slack, there should be no weight
on the motorcycle.
2. Shift the transmission into the neu-
tral position.
3. Move the rear wheel by pushing
the motorcycle to locate the tight-
est portion of the drive chain, and
then measure the drive chain slack
as shown.
Drive chain slack:
40.0–45.0 mm (1.57–1.77 in)

PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
2
3
4
5
67
8
9
CAUTION:

ECA11110
Do not use engine oil or any other lu-
bricants for the drive chain, as they
may contain substances that could
damage the O-rings.
EAU23100
Checking and lubricating the
cables
The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.
WARNING

EWA10720
Damage to the outer sheath may in-
terfere with proper cable operation
and will cause the inner cable to
rust. Replace a damaged cable as
soon as possible to prevent unsafe
conditions.
EAU23111
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.
Recommended lubricant:
Engine oil

PERIODIC MAINTENANCE AND MINOR REPAIR
6-24
1
2
3
4
5
6
7
8
9

EAU23271
Checking the front fork
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
WARNING

EWA10750
Securely support the vehicle so that
there is no danger of it falling over.
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the vehicle on a level sur-
face and hold it in an upright posi-
tion.
2. While applying the front brake,
push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
CAUTION:

ECA10590
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
EAU23280
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.
1. Place a stand under the engine to
raise the front wheel off the
ground.
WARNING

EWA10750
Securely support the vehicle so that
there is no danger of it falling over.
2. Hold the lower ends of the front
fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.

MOTORCYCLE CARE AND STORAGE
7-4
2
3
4
5
6
78
9
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to pro-
tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
WARNING

EWA10950
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
6. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
7. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
9. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place
[less than 0 °C (30 °F) or more
than 30 °C (90 °F)]. For more in-formation on storing the battery,
see page 6-25.
NOTE:

Make any necessary repairs before
storing the motorcycle.

INDEX
A
Air filter element and check hose, replacing
and cleaning ..........................................6-11
Auxiliary light bulb, replacing ...................6-30
B
Battery .....................................................6-25
Brake and clutch levers, checking and
lubricating ..............................................6-22
Brake and shift pedals, checking and
lubricating ..............................................6-22
Brake fluid, changing ...............................6-19
Brake fluid level, checking .......................6-18
Brake lever ................................................3-4
Brake lever free play, adjusting ...............6-16
Brake pedal ...............................................3-5
C
Cables, checking and lubricating .............6-21
Carburetor, adjusting ...............................6-12
Care ...........................................................7-1
Caution, matte black ..................................7-1
Clutch lever ................................................3-4
Clutch lever free play, adjusting ..............6-16
D
Dimmer switch ...........................................3-3
Drive chain, cleaning and lubricating .......6-20
Drive chain slack .....................................6-19
E
Engine break-in .........................................5-3
Engine idling speed .................................6-12
Engine oil and oil filter element ..................6-8
Engine, starting a warm .............................5-2
Engine stop switch.....................................3-3
F
Front and rear brake pads, checking .......6-17Front fork, checking ................................. 6-24
Fuel ........................................................... 3-6
Fuel cock ................................................... 3-6
Fuel consumption, tips for reducing .......... 5-3
Fuel tank cap ............................................. 3-5
Fuse, replacing ........................................ 6-27
H
Handlebar switches ................................... 3-3
Headlight bulb, replacing ......................... 6-27
Helmet holder ............................................ 3-8
High beam indicator light ........................... 3-2
Horn switch................................................ 3-3
I
Identification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-10
Indicator lights ........................................... 3-2
K
Key identification number .......................... 9-1
M
Main switch/steering lock .......................... 3-1
Model label ................................................ 9-2
N
Neutral indicator light................................. 3-2
P
Panels, removing and installing................. 6-5
Parking ...................................................... 5-4
Part locations............................................. 2-1
Periodic maintenance and lubrication
chart ........................................................ 6-2
Pre-operation check list ............................. 4-2
R
Rear brake light switch, adjusting............ 6-17
Rear suspension, lubricating ................... 6-23
S
Safety information ..................................... 1-1
Seat ........................................................... 3-8
Shifting ...................................................... 5-2
Shift pedal ................................................. 3-4
Shock absorber ......................................... 3-9
Sidestand .................................................. 3-9
Sidestand, checking and lubricating........ 6-23
Spark plug, checking ................................. 6-6
Specifications ............................................ 8-1
Speedometer unit ...................................... 3-2
Starter (choke) knob.................................. 3-7
Starting a cold engine ............................... 5-1
Start switch................................................ 3-3
Steering, checking................................... 6-24
Storage...................................................... 7-3
Storage pouch ........................................... 3-9
Supporting the motorcycle ...................... 6-31
T
Tail/brake light bulb, replacing ................ 6-29
Throttle cable free play, checking ........... 6-13
Throttle grip and cable, checking and
lubricating ............................................. 6-21
Tires ........................................................ 6-13
Tool kit....................................................... 6-1
Troubleshooting ...................................... 6-34
Troubleshooting chart ............................. 6-35
Turn signal indicator light .......................... 3-2
Turn signal light bulb, replacing .............. 6-29
Turn signal switch ..................................... 3-3
V
Valve clearance....................................... 6-13
Vehicle identification number .................... 9-1