2005 YAMAHA MAJESTY 125 maintenance

EAUS1241
Engine oil
1. Dipstick
(a) Maximum level (b) Minimum level
The engine oil level should be chec-
ked before each ride. In addition, the
oil must be changed at the intervals
specified in the periodic maintenance
and lubrication chart and when the oil
change indicator light comes on.
To check the engine oil level
1. Place the vehicle on the centers-
tand.
NOTE:
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it off.
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (without
screwing it in), and then remove it
again to check the oil level.
NOTE:
The engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to rai-
se it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.To change the engine oil
1. Drainage cap
1. Start the engine, warm it up for
several minutes, and then turn it off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and the engine oil drain bolt to
drain the oil from the crankcase.
ECA10410
CAUTION
When removing the engine oil drain
bolt, the O-ring, spring, and oil
strainer will fall out. Take care not
to lose these parts.
1
1a
b
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 36

1. O-ring
2. Compression spring
3. Strainer
4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, spring, O-
ring and engine drain bolt, and
then tighten the drain bolt to the
specified torque.
NOTE:
Make sure that the O-ring is properly
seated.
7. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
ECA11670
CAUTION
Do not use oils with a diesel
specification of “CD” or oils of
a higher quality than specified.
In addition, do not use oils
labeled “ENERGY CONSER-
VING II” or higher.
Be sure no foreign material
enters the crankcase.
8. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
9. Reset the oil change indicator
light according to the following
procedure.To reset the oil change indicator
light
1. Push and hold the “TRIP” button
for a MAXIMUM of three
seconds. While pushing the
“TRIP” button, turn the key to
“f”.
2. Release the “TRIP” button and
the oil change indicator light will
go off.
3. Turn the key to “e”.
NOTE:
If the engine oil is changed before the
oil change indicator light comes on
(i.e. before the periodic oil change
interval has been reached), the indi-
cator light must be reset after the oil
change for the next periodic oil chan-
ge to be indicated at the correct time.
To reset the oil change indicator light
before the periodic oil change interval
has been reached, follow the above
procedure, but note that the indicator
light will come on for 1.4 seconds
after releasing the reset button, other-
wise repeat the procedure.
Recommended engine oil:
See page 8-1.
Oil change quantity:
1,3 L (0,286 US qt) (1,144 Imp.qt)
Tightening torque:
Engine oil drain bolt:
32 Nm (3,2 m•kgf, 23,15ft•lb)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 37

EAU20011
Final gear oil
1. Oil filler cap
The final gear case must be checked
for oil leakage before each ride. If any
leakage is found, have a Yamaha dea-
ler check and repair the vehicle. In
addition, the final gear oil must be
changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
EWA10370
s s
WARNING
Make sure that no foreign
material enters the final gear
case.
Make sure that no oil gets on
the tire or wheel.
To check the final gear oil level
1. Place the vehicle on the centers-
tand.
1. Drain bolt
NOTE:
The final gear oil level must be
checked on a cold engine.
Make sure that the vehicle is posi-
tioned straight up when checking
the oil level. A slight tilt to the side
can result in a false reading.
2. Remove the oil filler bolt, and
then check the oil level in the final
gear case.
NOTE:
The oil level should be at the brim of
the filler hole.
3. If the oil is below the brim of the
filler hole, add sufficient oil of the
recommended type to raise it to
the correct level.
4. Install the oil filler bolt, and then
tighten it to the specified torque.
To change the final gear oil
1. Place an oil pan under the final
gear case to collect the used oil.
2. Remove the oil filler bolt and
drain bolt to drain the oil from the
final gear case.
3. Install the final gear oil drain bolt,
and then tighten it to the speci-
fied torque.
Tightening torque:
Final gear oil filler bolt:
22 Nm (2,2 m•kgf, 15,91 ft•lbf)
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 38

4. Add the recommended final gear
oil to the brim of the filler hole.
5. Install the oil filler bolt, and then
tighten it to the specified torque.
6. Check the final gear case for oil
leakage. If oil is leaking, check for
the cause.
EAU20070
Coolant
1. Maximum level
2. Minimum level
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAUS1080
To check the coolant level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
1. Coolant tank cap
2. Check the coolant level through
the check window.
NOTE:
The coolant should be between the
minimum and maximum level marks.
1
1
2
Recommended final gear oil:
Shaft drive gear oil (Part No.:
9079E-SH001-00)
Oil quantity:
0,15 L (0,033 US qt) (0,132 Imp.qt)
Tightening torque:
Final gear oil drain bolt:
22 Nm (2,2 m•kgf, 15,91 ft•lbf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 39

3. If the coolant is at or below the
minimum level mark, remove the
front cowling by removing the
screws.
4. Open the reservoir cap, and then
add coolant to the maximum
level mark.
ECA10470
CAUTION
If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.
If water has been used instead
of coolant, replace it with coo-
lant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the coo-
ling system will not be protec-
ted against frost and corrosion.
If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possi-
ble, otherwise the effective-
ness of the coolant will be
reduced.
5. Close the reservoir cap, and then
install the front cowling by insta-
lling the screws.
EAUM1320
Air filter and V-belt case air
filter elements
The air filter and the V-belt case air fil-
ter elements should be cleaned at the
intervals specified in the periodic
maintenance and lubrication chart.
Clean both filter elements more fre-
quently if you are riding in unusually
wet or dusty areas.Cleaning the air filter element
1. Air filter case cover
2. Screw (x 1)
1. Place the scooter on the centers-
tand.
2. Remove the air filter case cover
by removing the screws.
3. Pull the air filter element out.
1. Air filter
4. Lightly tap the air filter element to
remove most of the dust and dirt,
1
1
2
Coolant reservoir capacity:
0,45 L (0,099 US qt) (0,396 Imp.qt)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 40

and then blow the remaining dirt
out with compressed air.
5. Check the air filter element for
damage and replace it if neces-
sary.
6. Insert the air filter element into
the air filter case.
7. Install the air filter case cover by
installing the screws.
Cleaning the V-belt case air filter
element
1. V-belt case air filter cover
2. Screw (x 3)
3. Air filter element
1. Remove the V-belt case air filter
cover by removing the screws.
2. Remove the air filter element, and
then blow out the dirt with com-
pressed air as shown.3. Check the air filter element for
damage and replace it if neces-
sary.
4. Install the air filter element with
the colored side facing outward.
5. Install the V-belt case air filter
cover by installing the screws.
ECA10530
CAUTION
Make sure that each filter ele-
ment is properly seated in its
case.
The engine should never be
operated without the filter ele-
ments installed, otherwise the
piston(s) and/or cylinder(s)
may become excessively worn.
EAU21300
Adjusting the carburetor
The carburetor is an important part of
the engine and requires very sophisti-
cated adjustment. Therefore, all car-
buretor adjustments should be left to
a Yamaha dealer, who has the neces-
sary professional knowledge and
experience.
EAU21381
Checking the throttle cable
free play
The throttle cable free play should
measure 1,5~3,0 mm (0,060~0,118 in)
at the throttle grip. Periodically check
the throttle cable free play and, if
necessary, have a Yamaha dealer
adjust it.
1
23
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 41

EAU21540
Tires
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be chec-
ked and, if necessary, adjusted befo-
re each ride.
EWA10500
s s
WARNING
The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperatu-
re of the tires equals the
ambient temperature).
The tire air pressure must be
adjusted in accordance with
the riding speed and with thetotal weight of rider, passenger,
cargo, and accessories appro-
ved for this model.
EWA11020
s s
WARNING
Because loading has an enormous
impact on the handling, braking,
performance and safety characte-
ristics of your motorcycle, you
should keep the following precau-
tions in mind.
NEVER OVERLOAD THE
MOTORCYCLE! Operation of
an overloaded motorcycle may
result in tire damage, loss of
control, or severe injury. Make
sure that the total weight of
rider, passenger, cargo, and
accessories does not exceed
the specified maximum load
for the vehicle.
Do not carry along loosely pac-
ked items, which can shift
during a ride.
Securely pack the heaviest
items close to the center of the
motorcycle and distribute the
weight evenly on both sides.
Adjust the suspension and tire
air pressure with regard to the
load.
Check the tire condition and air
pressure before each ride.
Tire air pressure (measured on
cold tires):
Up to 90 kg (198 lb):
Front:
190 kPa (27,02 psi)
(1,9 kgf/cm
2)
Rear:
220 kPa (31,29 psi)
(2,2 kgf/cm
2)
90 kg (198 lb) to maximum load:
Front:
190 kPa (27,02 psi)
(1,9 kgf/cm
2)
Rear:
240 kPa (34,14 psi)
(2,4 kgf/cm
2)
Maximum load*:
183 kg (403,51 lb)
* Total weight of rider, passenger, car-
go and accessories
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 42

Tire inspection
1. Depth
2. Side face
The tires must be checked before
each ride. If the center tread depth
reaches the specified limit, if the tire
has a nail or glass fragments in it, or if
the sidewall is cracked, have a Yama-
ha dealer replace the tire immediately.
NOTE:
The tire tread depth limits may differ
from country to country. Always
comply with the local regulations.
Tire information
This motorcycle is equipped with tube
tires.
EWA10460
s s
WARNING
The front and rear tires should
be of the same make and
design, otherwise the handling
characteristics of the vehicle
cannot be guaranteed.
After extensive tests, only the
tires listed below have been
approved for this model by
Yamaha Motor España, S.A.
EWA10570
s s
WARNING
Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
motorcycle with excessively
worn tires decreases riding
stability and can lead to loss of
control.
The replacement of all wheel-
and brake-related parts, inclu-
ding the tires, should be left to
a Yamaha dealer, who has the
necessary professional know-
ledge and experience.
It is not recommended to patch
a punctured tube. If unavoida-
ble, however, patch the tube
very carefully and replace it as
soon as possible with a high-
quality product.Front tire:
Size:
120/70-12 51L
Manufacturer/model:
MICHELIN
CHENG SING
PIRELLI
Rear tire:
Size:
130/70-12 56L
Manufacturer/model:
MICHELIN
CHENG SING
PIRELLI
Minimum tire tread depth (front
and rear):
1.6 mm (0.06 in)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
5XL-F8199-E3.qxd 19/09/2005 16:26 Página 43