2005 YAMAHA DT125R warning

Tire inspection
1.Wear limit
2. Side wall
The tires must be checked before
each ride. If the center tread depth
reaches the specified limit, if the tire
has a nail or glass fragments in it, or if
the sidewall is cracked, have a Yama-
ha dealer replace the tire immediately.
Minimum tire tread depth (front and
rear):
1.6 mm (0.06 in)
NOTE:
The tire tread depth limits may differ
from country to country. Always
comply with the local regulations.
Tire information
This motorcycle is equipped with tube
tires.
EWA10460
s s
WARNING
The front and rear tires should
be of the same make and
design, otherwise the handling
characteristics of the vehicle
cannot be guaranteed.
After extensive tests, only the
tires listed below have been
approved for this model by
Yamaha Motor España, S.A.
DT125R
Front tire:
Size:
80/90-21 48P
Manufacturer/model:
MICHELIN / T63
Rear tire:
Size:
110/80-18 58P
Manufacturer/model:
MICHELIN / T63
DT125X
Front tire:
Size:
120/70-17 58H
Manufacturer/model:
Pirelli/Sport Demon
Rear tire:
Size:
140/70-17 66H
Manufacturer/model:
Pirelli/Sport Demon
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
1
2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 45

EWA10570
s s
WARNING
Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
motorcycle with excessively
worn tires decreases riding
stability and can lead to loss of
control.
The replacement of all wheel-
and brake-related parts, inclu-
ding the tires, should be left to
a Yamaha dealer, who has the
necessary professional know-
ledge and experience.
It is not recommended to patch
a punctured tube. If unavoida-
ble, however, patch the tube
very carefully and replace it as
soon as possible with a high-
quality product.
EAU21940
Spoke wheels
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified wheels.
The wheel rims should be chec-
ked for cracks, bends or warpa-
ge, and the spokes for looseness
or damage before each ride. If
any damage is found, have a
Yamaha dealer replace the whe-
el. Do not attempt even the sma-
llest repair to the wheel. A defor-
med or cracked wheel must be
replaced.
The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for
it to develop its optimal characte-
ristics.
EAU22041
Adjusting the clutch lever
free play
1. Lock nut
2. Adjusting bolt
3. Free play
The clutch lever free play should mea-
sure 10-15 mm (0,34-0,59 in) as
shown. Periodically check the clutch
lever free play and, if necessary,
adjust it as follows.
1. Loosen the locknut at the clutch
lever.
2. To increase the clutch lever free
play, turn the adjusting bolt in
direction (a). To decrease the
clutch lever free play, turn the
adjusting bolt in direction (b).6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-15
1
2 3
1D0-F8199-E2.qxd 20/9/04 11:32 Página 46

NOTE:
If the specified clutch lever free play
could be obtained as described abo-
ve, tighten the locknut and skip the
rest of the procedure, otherwise pro-
ceed as follows.
3. Fully turn the adjusting bolt at the
clutch lever in direction (a) to loo-
sen the clutch cable.
1. Lock nut
2. Adjusting nut
4. Loosen the locknut at the crank-
case.
5. To increase the clutch lever free
play, turn the adjusting nut in
direction (a). To decrease the
clutch lever free play, turn the
adjusting nut in direction (b).6. Tighten the locknut at the clutch
lever and the crankcase.
EAU22092
Adjusting the brake lever
free play
1. Lock nut
2. Adjusting bolt
3. Free play
The brake lever free play should mea-
sure 2-5 mm (0,07 ~ 0,19 in) as
shown. Periodically check the brake
lever free play and, if necessary,
adjust it as follows.
1. Loosen the locknut at the brake
lever.2. To increase the brake lever free
play, turn the adjusting screw in
direction (a). To decrease the bra-
ke lever free play, turn the adjus-
ting screw in direction (b).
3. Tighten the locknut.
EWA10630
s s
WARNING
After adjusting the brake lever
free play, check the free play
and make sure that the brake is
working properly.
A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic
system. If there is air in the
hydraulic system, have a
Yamaha dealer bleed the sys-
tem before operating the
motorcycle. Air in the hydraulic
system will diminish the bra-
king performance, which may
result in loss of control and an
accident.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-16
2
1
123
1D0-F8199-E2.qxd 20/9/04 11:32 Página 47

EAU22192
Adjusting the brake pedal
position and free play
1. Footrest
(a) Brake pedal position
EWA10670
s s
WARNING
It is advisable to have a Yamaha
dealer make these adjustments.
Brake pedal position
The top of the brake pedal should be
positioned approximately 12-15 mm
(0,47-0,49 in) below the top of the
footrest. Periodically check the brake
pedal position and, if necessary,
adjust it as follows.
1. Loosen the locknut at the brake
pedal.2. To raise the brake pedal, turn the
adjusting bolt in direction (a). To
lower the brake pedal, turn the
adjusting bolt in direction (b).
3. Tighten the locknut.
EWA11230
s s
WARNING
After adjusting the brake pedal
position, the brake pedal free play
must be adjusted.
Brake pedal free play
The brake pedal free play should
measure 10-15 mm (0,34-0,59 in) as
shown. Periodically check the brake
pedal free play and, if necessary,
adjust it as follows.
To increase the brake pedal free play,
turn the adjusting nut at the brake rod
in direction (a). To decrease the brake
pedal free play, turn the adjusting nut
in direction (b).
EWA10680
s s
WARNING
After adjusting the drive chain
slack or removing and installing
the rear wheel, always check
the brake pedal free play.
If proper adjustment cannot be
obtained as described, have a
Yamaha dealer make this
adjustment.
After adjusting the brake pedal
free play, check the operation
of the brake light.
EAU22270
Adjusting the rear brake light
switch
1. Brake light swicht
2. Adjusting nut
The rear brake light switch, which is
activated by the brake pedal, is pro-
perly adjusted when the brake light
comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
1
1
2
1D0-F8199-E2.qxd 20/9/04 11:32 Página 48

Turn the adjusting nut while holding
the rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a).
To make the brake light come on later,
turn the adjusting nut in direction (b).
EAU22340
Checking the front and rear
brake pads
1. Wear limit indicator
The front and rear brake pads must
be checked for wear at the intervals
specified in the periodic maintenance
and lubrication chart. To check the
brake pad wear, measure the lining
thickness. If the lining thickness is
less than 0,8 mm (0,03 in), have a
Yamaha dealer replace the brake
pads as a set.
EWA10250
s s
WARNING
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
1. Wear indicator
EAU22580
Checking the brake fluid level
1. Minimum level mark
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.Before riding, check that the brake
fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the
brake fluid reservoir is level.
1. Minimum level mark

Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
FRONTREAR
FRONTREAR
11
11
1D0-F8199-E2.qxd 20/9/04 11:32 Página 49

EAU23100
Checking and lubricating the
cables
The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends should
be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or repla-
ce it.
Recommended lubricant:
Engine oil
EWA10720
s s
WARNING
Damage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
EAU23110
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated or replaced at the intervals spe-
cified in the periodic maintenance
chart.
EAU23120
Adjusting the Autolube pump
The Autolube pump is a vital and sop-
histicated component of the engine,
which must be adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.
EAU23131
Checking and lubricating the
brake and shift pedals
The operation of the brake and shift
pedals should be checked before
each ride, and the pedal pivots
should be lubricated if necessary.
Recommended lubricant:
Lithium-soap-based grease (all-pur-
pose grease)
EAU23140
Checking and lubricating the
brake and clutch levers
The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be
lubricated if necessary.
Recommended lubricant:
Lithium-soap-based grease (all-pur-
pose grease)
EAU23200
Checking and lubricating the
sidestand
The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated
if necessary.
EWA10730
s s
WARNING
If the sidestand does not move up
and down smoothly, have a Yama-
ha dealer check or repair it.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
1D0-F8199-E2.qxd 20/9/04 11:32 Página 52

Recommended lubricant:
Lithium-soap-based grease (all-pur-
pose grease)
EAU23271
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the perio-
dic maintenance and lubrication
chart.
To check the condition
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
Check the inner tubes for scratches,
damage and excessive oil leakage.To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.
2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and
rebounds smoothly.ECA10590
CAUTION
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
EAU23280
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place a stand under the engine to
raise the front wheel off the
ground.
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-22
1D0-F8199-E2.qxd 20/9/04 11:32 Página 53

2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the stee-
ring.
EAU23290
Checking the wheel bearings
The front and rear wheel bearings
must be checked at the intervals spe-
cified in the periodic maintenance and
lubrication chart. If there is play in the
wheel hub or if the wheel does not
turn smoothly, have a Yamaha dealer
check the wheel bearings.
EAU23380
Battery
1. Battery
2. Battery ventilation pipe
The battery is located behind panel D.
(See page 6-6.)
This model is equipped with a sealed-
type (MF) battery, which does not
require any maintenance. There is no
need to check the electrolyte or to
add distilled water.
ECA10620
CAUTION
Never attempt to remove the bat-
tery cell seals, as this would per-
manently damage the battery.
EWA10760
s s
WARNING
Electrolyte is poisonous and
dangerous since it contains
sulfuric acid, which causes
severe burns. Avoid any con-
tact with skin, eyes or clothing
and always shield your eyes
when working near batteries.
In case of contact, administer
the following FIRST AID.
• EXTERNAL: Flush with plenty
of water.
• INTERNAL: Drink large quan-
tities of water or milk and
immediately call a physician.• EYES: Flush with water for 15
minutes and seek prompt
medical attention.
• Batteries produce explosive
hydrogen gas. Therefore,
keep sparks, flames, cigaret-
tes, etc., away from the bat-
tery and provide sufficient
ventilation when charging it
in an enclosed space.
KEEP THIS AND ALL BATTE-
RIES OUT OF THE REACH OF
CHILDREN.
To charge the battery
Have a Yamaha dealer charge the
battery as soon as possible if it seems
to have discharged. Keep in mind that
the battery tends to discharge more
quickly if the vehicle is equipped with
optional electrical accessories.
To store the battery
1. If the vehicle will not be used for
more than one month, remove
the battery, fully charge it, and
then place it in a cool, dry place.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-23
2
1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 54