2005 YAMAHA DT125R warning

EAU15090
Shock absorberEWA10220
s s
WARNING
This shock absorber contains
highly pressurized nitrogen gas.
For proper handling, read and
understand the following informa-
tion before handling the shock
absorber. The manufacturer cannot
be held responsible for property
damage or personal injury that may
result from improper handling.
Do not tamper with or attempt
to open the gas cylinder.
Do not subject the shock
absorber to an open flame or
other high heat sources, other-
wise it may explode due to
excessive gas pressure.
Do not deform or damage the
gas cylinder in any way, as this
will result in poor damping per-
formance.
Always have a Yamaha dealer
service the shock absorber.
EAU15250
YEIS handling precautions
1. YEIS
Improper installation of or damage to
any part of the YEIS (Yamaha Energy
Induction System) will result in poor
performance. Therefore, handle the
YEIS air chamber and air chamber
hose with special care and immedia-
tely replace any cracked or damaged
parts.
ECA10140
CAUTION
Do not attempt to modify the YEIS
in any way.
EAU15260
YPVS
1. YPVS
This model is equipped with the YPVS
(Yamaha Power Valve System). This
system boosts engine performance
and efficiency by means of a variable
valve in the exhaust port. The YPVS
valve is constantly adjusted in accor-
dance with the engine speed by a
computer-controlled servomotor.
Since the YPVS is an important part
of the engine and requires very sop-
histicated adjustment, have a Yamaha
dealer, who has the necessary profes-
sional knowledge and experience,
make this adjustment.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-9
1
1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 23

ECA10150
CAUTION
The YPVS has been set and exten-
sively tested at the Yamaha factory.
Changing these settings without
sufficient technical knowledge may
result in poor performance of or
damage to the engine.
YPVS operation noises can be heard
in the following instances:
When the key is turned to “ON”
and the engine is started.
When the engine stalls with the
key in the “ON” position.
ECA10160
CAUTION
If the YPVS does not operate, have
a Yamaha dealer check it.
EAU15300
Sidestand
The sidestand is located on the left
side of the frame. Raise the sidestand
or lower it with your foot while holding
the motorcycle upright.
NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain
situations. (See further down for an
explanation of the ignition circuit cut-
off system.)
EWA10240
s s
WARNING
The vehicle must not be ridden with
the sidestand down, or if the sides-
tand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control. Yama-
ha’s ignition circuit cut-off system
has been designed to assist the
operator in fulfilling the responsibi-
lity of raising the sidestand before
starting off. Therefore, check this
system regularly as described
below and have a Yamaha dealer
repair it if it does not function pro-
perly.
EAU15311
Ignition circuit cut-off
system
The ignition circuit cut-off system
(comprising the sidestand switch,
clutch switch and neutral switch) has
the following functions.
It prevents starting when the
transmission is in gear and the
sidestand is up, but the clutch
lever is not pulled.
It prevents starting when the
transmission is in gear and the
clutch lever is pulled, but the
sidestand is still down.
It cuts the running engine when
the transmission is in gear and
the sidestand is moved down.
Periodically check the operation of
the ignition circuit cut-off system
according to the following procedure.
EWA10250
s s
WARNING
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-10
1D0-F8199-E2.qxd 20/9/04 11:32 Página 24

EAU15591
The condition of a vehicle is the
owner’s responsibility. Vital compo-
nents can start to deteriorate quickly
and unexpectedly, even if the vehicle
remains unused (for example, as a
result of exposure to the elements).
Any damage, fluid leakage or loss of
tire air pressure could have serious
consequences. Therefore, it is very
important, in addition to a thorough
visual inspection, to check the follo-
wing points before each ride.
NOTE:
Pre-operation checks should be
made each time the vehicle is used.
Such an inspection can be accom-
plished in a very short time; and the
added safety it assures is more than
worth the time involved.
EWA11150
s s
WARNING
If any item in the Pre-operation
check list is not working properly,
have it inspected and repaired
before operating the vehicle.
4
PRE-OPERATION CHECKS
4-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 24

EAU15950
EWA10270
s s
WARNING
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thoroughly
understand.
Never start the engine or ope-
rate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of cons-
ciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised comple-
tely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU16060
Starting a cold engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
s s
WARNING
Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-11.
Never ride with the sidestand
down.
1. Turn the fuel cock lever to “ON”.
2. Turn the key to “ON” and make
sure that the engine stop switch
is set to “f”.
3. Shift the transmission into the
neutral position.
NOTE:
When the transmission is in the neu-
tral position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical
circuit.
4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-8.)
5. Start the engine by pushing the
start switch.
NOTE:
If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the
engine more than 10 seconds on any
one attempt.
6. After starting the engine, move
the starter (choke) back halfway.
ECA11040
CAUTION
For maximum engine life, never
accelerate hard when the engine is
cold!
5
OPERATION AND IMPORTANT RIDING POINTS
5-1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 29

After every hour of operation, stop the
engine, and then let it cool for five to
ten minutes.
Vary the engine speed from time to
time. Do not operate the engine at
one set throttle position.
150–500 km (90–300 mi)
Avoid prolonged operation above 1/2
throttle.
Rev the engine freely through the
gears, but do not use full throttle at
any time.
500–1000 km (300–600 mi)
Avoid prolonged operation above 3/4
throttle.
ECA10370
CAUTION
After 1000 km (600 mi) of operation,
the transmission oil must be chan-
ged.
1000 km (600 mi) and beyond
Avoid prolonged full-throttle opera-
tion. Vary the engine speed occasio-
nally.
ECA10270
CAUTION
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.
EAU17180
Parking
When parking, stop the engine, remo-
ve the key from the main switch, and
then turn the fuel cock lever to “OFF”.
EWA10310
s s
WARNING
Since the engine and exhaust
system can become very hot,
park in a place where pedes-
trians or children are not likely
to touch them.
Do not park on a slope or on
soft ground, otherwise the
vehicle may overturn.
ECA10380
CAUTION
Never park in an area where there
are fire hazards such as grass or
other flammable materials.
5
OPERATION AND IMPORTANT RIDING POINTS
5-3
1D0-F8199-E2.qxd 20/9/04 11:32 Página 31

EAU17240
Safety is an obligation of the owner.
Periodic inspection, adjustment and
lubrication will keep your vehicle in
the safest and most efficient condi-
tion possible. The most important
points of inspection, adjustment, and
lubrication are explained on the follo-
wing pages.
The intervals given in the periodic
maintenance and lubrication chart
should be simply considered as a
general guide under normal riding
conditions. However, DEPENDING
ON THE WEATHER, TERRAIN, GEO-
GRAPHICAL LOCATION, AND INDIVI-
DUAL USE, THE MAINTENANCE
INTERVALS MAY NEED TO BE
SHORTENED.
EWA10320
s s
WARNING
If you are not familiar with mainte-
nance work, have a Yamaha dealer
do it for you.
EAU17320
Owner’s tool kit
1. Tool kit
The service information included in
this manual and the tools provided in
the owner’s tool kit are intended to
assist you in the performance of pre-
ventive maintenance and minor
repairs. However, additional tools
such as a torque wrench may be
necessary to perform certain mainte-
nance work correctly.
NOTE:
If you do not have the tools or expe-
rience required for a particular job,
have a Yamaha dealer perform it for
you.
EWA10350
s s
WARNING
Modifications not approved by
Yamaha may cause loss of perfor-
mance and render the vehicle
unsafe for use. Consult a Yamaha
dealer before attempting any chan-
ges.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-1
1
1D0-F8199-E2.qxd 20/9/04 11:32 Página 32

NOTE:
The coolant should be between the
minimum and maximum level marks.
4. If the coolant is at or below the
minimum level mark, open the
reservoir cap, add coolant to the
maximum level mark, and then
close the reservoir cap.
Coolant reservoir capacity:
0,3 L (0,32 US qt)
ECA10470
CAUTION
If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.
If water has been used instead
of coolant, replace it with coo-
lant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the coo-
ling system will not be protec-
ted against frost and corrosion.
If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possi-
ble, otherwise the effective-
ness of the coolant will be
reduced.
EWA10380
s s
WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
5. Install the panel.
NOTE:
If the engine overheats, see page
6-31 for further instructions.
EAU20370
To change the coolant
1. Radiator cap bolt
2. Radiador cap
1. Put the vehicle on a level place.
2. Remove cowling C and panel D.
(See page 6-5 ~ 6-6.)
3. Remove the radiator cap stopper
bolt and the radiator cap.
1. Drain bolt
4. Place a container under the engi-
ne and remove the coolant drain
bolt.
5. Disconnect the coolant reservoir
hose on the reservoir side and
drain the coolant from the reser-
voir.
6. After draining the coolant, tho-
roughly flush the cooling system
with clean tap water.
7. Replace the coolant drain bolt
washer if it is damaged, and then
tighten the coolant drain bolt to
the specified torque.6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
2
11
1D0-F8199-E2.qxd 20/9/04 11:32 Página 40

EAU21590
Tires
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be chec-
ked and, if necessary, adjusted befo-
re each ride.
EWA10500
s s
WARNING
The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperatu-
re of the tires equals the
ambient temperature).
The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passenger,
cargo, and accessories appro-
ved for this model.
Tire air pressure (measured on cold
tires):
DT125R
Up to 90 kg (198 lb):
Front:
150 kPa (21,8 psi) (1,5 kgf/cm
2)
Rear:
175 kPa (25,4 psi) (1,75 kgf/cm
2)
90 kg (198 lb) to maximum load:
Front:
175 kPa (25,4 psi) (1,75 kgf/cm
2)
Rear:
200 kPa (28,9 psi) (2 kgf/cm
2)
Maximum load*:
178 kg (392 lb)
DT125X
Up to 90 kg (198 lb):
Front:
180 kPa (26,1 psi) (1,8 kgf/cm
2)
Rear:
200 kPa (28,9 psi) (2 kgf/cm
2)
90 kg (198 lb) to maximum load:
Front:
180 kPa (26,1 psi) (1,8 kgf/cm
2)
Rear:
200 kPa (28,9 psi) (2 kgf/cm
2)
Maximum load*:
180 kg (396 lb)
* Total weight of rider, passenger, car-
go and accessories
EWA11200
s s
WARNING
Because loading has an enormous
impact on the handling, braking,
performance and safety characte-
ristics of your vehicle, you should
keep the following precautions in
mind.
NEVER OVERLOAD THE VEHI-
CLE! Operation of an overloa-
ded motorcycle may result in
tire damage, loss of control, or
severe injury. Make sure that
the total weight of rider, pas-
senger, cargo, and accessories
does not exceed the specified
maximum load for the vehicle.
Do not carry along loosely pac-
ked items, which can shift
during a ride.
Securely pack the heaviest
items close to the center of the
vehicle and distribute the
weight evenly on both sides.
Adjust the tire air pressure with
regard to the load.
Check the tire condition and air
pressure before each ride.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
1D0-F8199-E2.qxd 20/9/04 11:32 Página 44