2005 YAMAHA BRUIN 250 oil level

OPERATION ............................................6-1
Starting a cold engine ...........................6-3
Starting a warm engine ........................6-9
Warming up ..........................................6-9
Drive select lever operation and
reverse driving ..................................6-11
Shifting ................................................6-15
To start out and accelerate .................6-17
To decelerate ......................................6-19
Engine break-in ...................................6-21
Parking ...............................................6-23
Parking on a slope ..............................6-25
Accessories and loading ....................6-27
RIDING YOUR ATV..................................7-1
Getting to know your ATV .....................7-3
Ride with care and good judgement .....7-5
Be careful where you ride ...................7-27
Turning your ATV ................................7-41
Climbing uphill.....................................7-47
Riding downhill ....................................7-57
Crossing a slope .................................7-61
Crossing through shallow water ..........7-65
Riding over rough terrain ....................7-71
Sliding and skidding ............................7-73
What to do if ........................................7-77
What to do...........................................7-77
67
PERIODIC MAINTENANCE AND
ADJUSTMENT ......................................... 8-1
Owner’s manual and tool kit ................. 8-3
Periodic maintenance/lubrication.......... 8-7
Engine oil and oil filter element........... 8-17
Final gear oil ....................................... 8-31
Spark plug inspection ......................... 8-37
Air filter element cleaning ................... 8-43
Carburetor adjustment ....................... 8-49
Idle speed adjustment ........................ 8-51
Valve clearance adjustment .............. 8-53
Throttle lever adjustment ................... 8-53
Select lever safety system cable
adjustment ........................................ 8-55
Front brake pad check ........................ 8-55
Rear brake shoe inspection ............... 8-57
Brake fluid level check ........................ 8-59
Brake fluid replacement ...................... 8-61
Front brake lever free play.................. 8-63
Adjusting the brake pedal and rear
brake lever........................................ 8-65
Adjusting the rear brake light switch ... 8-73
Clutch adjustment ............................... 8-75
Cable inspection and lubrication......... 8-77
Brake lever and brake pedal
lubrication ........................................ 8-79
Steering shaft lubrication .................... 8-81
8
U1P060.book Page 2 Monday, August 2, 2004 12:19 PM

5-1
EBU00113
1-PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
Front brakeCheck operation, free play, fluid level and fluid leakage.
Fill with DOT 4 brake fluid if necessary.5-5–5-7,
8-55–8-63
Rear brakeCheck operation, condition and free play.
Adjust if necessary.5-5–5-7,
8-57, 8-65–8-71
FuelCheck fuel level.
Fill with fuel if necessary.5-9–5-11
Engine oilCheck oil level.
Fill with oil if necessary.5-13, 8-17–8-29
Final gear oilCheck for leakage. 5-15, 8-31–8-35
ThrottleCheck for proper throttle cable operation. 5-15, 8-53
Wheels and tiresCheck tire pressure, wear and damage.5-19–5-25,
8-81–8-83
Fittings and fastenersCheck all fittings and fasteners. 5-17
Lights and switchesCheck for proper operation. 5-17, 8-95–8-101
BatteryCheck fluid level.
Fill with distilled water if necessary.5-17, 8-85–8-91
U1P060.book Page 1 Monday, August 2, 2004 12:19 PM

5-13
EBU10842
Engine oil
Make sure the engine oil is at the specified level.
Add oil as necessary. (See pages 8-17–8-29.)CAUTION:_

In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD”
or oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING II” or higher.


Make sure that no foreign material enters
the crankcase.
_
Recommended engine oil type and quantity:
See page 10-2.
U1P060.book Page 13 Monday, August 2, 2004 12:19 PM

5-15
EBU00493
Final gear oil
Make sure the final gear oil is at the specified level.
Add oil as necessary. (See pages 8-31–8-35 for
details.)
If desired, an SAE 80W90 hypoid gear oil may be
used for all conditions.NOTE:GL-4 is a quality and additive rating, GL-5 or GL-6
rated hypoid gear oils may also be used.
EBU01083
Throttle lever
Check to see that the throttle lever operates cor-
rectly. It must open smoothly and spring back to
the idle position when released. Have a Yamaha
dealer repair as necessary for proper operation.Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
U1P060.book Page 15 Monday, August 2, 2004 12:19 PM

8-8
Engine oil strainer
Clean.Final gear oilCheck oil level/oil leakage.
Replace.Front brake*Check operation/fluid leakage/see NOTE page 8-9.
Correct if necessary.Rear brake*Check operation.
Adjust if necessary.Select lever safety
system cable*Check operation.
Adjust if necessary.Clutch*Check operation.
Adjust if necessary.Wheels*Check balance/damage/runout.
Repair if necessary.Wheel bearings*Check bearing assemblies for looseness/damage.
Replace if damaged.Front and rear
suspension*Check operation.
Correct if necessary.Steering system*Check operation./Replace if damaged.
Check toe-in./Adjust if necessary.Steering shaft*Lubricate every 6 months with lithium-soap-based grease
(all-purpose grease).Fittings and fasteners*Check all chassis fittings and fasteners.
Correct if necessary.
ITEM ROUTINEWhichever
comes firstINITIAL EVERY
month136612
km
(mi)320
(200)1,200
(750)2,400
(1,500)2,400
(1,500)4,800
(3,000)
hours 20 75 150 150 300
U1P060.book Page 8 Monday, August 2, 2004 12:19 PM

8-9 * It is recommended that these items be serviced by a Yamaha dealer.
NOTE:

Recommended brake fluid: DOT 4


Brake fluid replacement:
When disassembling the master cylinder or caliper, replace the brake fluid. Normally check the
brake fluid level and add fluid as required.
On the inner parts of the master cylinder and caliper, replace the oil seals every two years.
Replace the brake hoses every four years, or if cracked or damaged.
Battery*Check specific gravity.
Check that the breather hose is routed correctly.
Correct if necessary.Lights and switches*Check operation.
Adjust headlight beams.
ITEM ROUTINEWhichever
comes firstINITIAL EVERY
month136612
km
(mi)320
(200)1,200
(750)2,400
(1,500)2,400
(1,500)4,800
(3,000)
hours 20 75 150 150 300
U1P060.book Page 9 Monday, August 2, 2004 12:19 PM

8-17 1. Engine oil filler cap
2. Dipstick
3. Maximum level mark
4. Minimum level mark
1. Bouchon de remplissage d’huile de moteur
2. Jauge
3. Repère de niveau maximum
4. Repère de niveau minimum
1. Tapa del filtro de aceite de motor
2. Varilla de nivel de aceite
3. Marca de nivel máximo
4. Marca de nivel mínimo
EBU11005
Engine oil and oil filter element
The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter element cleaned at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
To check the engine oil level
1. Place the ATV on a level surface.
2. Warm up the engine for several minutes, and
then turn it off.
3. Wait at least ten minutes until the oil level set-
tles before checking.
4. Remove the engine oil filler cap, and then
wipe the dipstick off with a clean rag. Insert
the dipstick in the filler hole (without screwing
it in), and then remove it again to check the oil
level.NOTE:_

Be sure to wait at least ten minutes until the
oil level settles before checking.


The oil level should be between the minimum
and maximum level marks.
_
U1P060.book Page 17 Monday, August 2, 2004 12:19 PM

8-19 1. Engine oil drain bolt 2. O-ring
3. Compression spring 4. Engine oil strainer
1. Boulon de vidange de l’huile moteur
2. Joint torique
3. Ressort de compression
4. Crépine à huile de moteur
1. Perno de drenaje del aceite de motor
2. Junta tórica
3. Muelle de compresión
4. Tamiz de aceite de motor
5. If the engine oil is at or below the minimum
level mark, add sufficient oil of the recom-
mended type to raise it to the correct level.CAUTION:_ Make sure that no foreign material enters the
crankcase. _6. Insert the dipstick into the oil filler hole, and
then tighten the engine oil filler cap.
To change the engine oil (with or without oil fil-
ter element cleaning)
1. Place the ATV on a level surface.
2. Warm up the engine for several minutes, and
then turn it off.
3. Place a container under the engine to collect
the used oil.
4. Remove the engine oil filler cap, and then re-
move the engine oil drain bolt to drain the oil
from the crankcase.
U1P060.book Page 19 Monday, August 2, 2004 12:19 PM