2005 TOYOTA TUNDRA airbag

’05 TUNDRA_U (L/O 0408)
127
2005 TUNDRA from Aug. ’04 Prod. (OM34427U)
(C) BOOSTER SEAT INSTALLATION
A booster seat must be used in for-
ward−facing position only.
Move seat fully back
CAUTION
Vehicles with split bench seat—A
forward −facing child restraint sys-
tem should be allowed to be
installed on the front passenger
seat only when it is unavoidable.
Always move the seat as far back
as possible, because the front pas-
senger airbag could inflate with
considerable speed and force.
Otherwise, the child may be killed
or seriously injured.
Vehicles with separate seat—A for-
ward −facing child restraint system
should be allowed to be installed
on the front passenger seat only
when it is unavoidable. Always
move the seat as far back as pos-
sible even if the front passenger
occupant classification indicator
light indicates “OFF”, because the
front passenger airbag could inflate
with considerable speed and force.
Otherwise, the child may be killed
or seriously injured.
On vehicles with side airbags and
curtain shield airbags, do not allow
the child to lean his/her head or
any part of his/her body against the
door or the area of the seat, front
or rear pillar or roof side rail from
which the side airbags or curtain
shield airbags deploy even if the
child is seated in the child restraint
system. It is dangerous if the side
airbag and curtain shield airbag in-
flate, and the impact could cause
death or serious injury to the child.

’05 TUNDRA_U (L/O 0408)
178
2005 TUNDRA from Aug. ’04 Prod. (OM34427U)
When the brake fluid level is too low, the
traction control system, “AUTO LSD” sys-
tem and vehicle stability control system
will not operate and the warning light
comes on.
(j) Open Door Warning Light
This light remains on until all the doors
are completely closed.
(k) SRS Warning Light
This light will come on when the igni-
tion key is turned to the “ON” position.
After about 6 seconds, the light will go
off. This means the system of the air-
bag and front seat belt pretensioners
are operating properly.
This warning light system monitors the
airbag sensor assembly, front airbag sen-
sors, side and curtain shield airbag sen-
sors, curtain shield airbag sensors, driv-
er ’s seat position sensor, driver ’s seat belt
buckle switch, front passenger occupant
classification system and indicator light,
passenger airbag manual on −off switch,
front passenger ’s seat belt buckle switch,
seat belt pretensioner assemblies, inflat-
ors, warning light, “RSCA OFF” indicator
light, interconnecting wiring and power
sources. If either of the following conditions occurs,
this indicates a malfunction somewhere in
the parts monitored by the warning light
system. Contact your Toyota dealer as
soon as possible to service the vehicle.
The light does not come on when the
ignition key is turned to the “ON” posi-
tion or remains on for more than 6
seconds.
The light comes on while driving.
(l) Low Tire Pressure Warning Light
This light warns that the tire pressure of
one or more of your tires (including the
spare tire) is low. The light comes on
when the ignition key is turned to the
“ON” position. It goes off after a few sec-
onds. This indicates that the tire pressure
warning system is functioning properly.
If the warning light comes on, stop your
vehicle in a safe place as soon as pos-
sible and check that the inflation pressure
of all tires (including the spare tire) is as
specified on the tire and loading informa-
tion label. (See “Checking tire inflation
pressure” in Section 7 −2.) The light should
go off a few minutes after the tire pres-
sure is adjusted.
If the warning light blinks, the tire pres-
sure warning system may be malfunction-
ing. Contact your Toyota dealer. For details, see “Tire pressure warning
system” in Section 1
−7.
(m) Automatic Transmission Fluid Temperature Warning Light
(four −wheel drive models)
This light warns that the automatic trans-
mission fluid temperature is too high.
If this light comes on while you are driv-
ing, slow down and pull off the road. Stop
the vehicle at a safe place and put the
selector lever in “P”. With the engine id-
ling, wait until the light goes off. If the
light goes off, you may start the vehicle
again. If the light does not go off, call a
Toyota dealer or qualified repair shop for
assistance.
(n) Low Windshield Washer Fluid Level Warning Light
This light warns that the windshield wash-
er fluid level is too low. Add washer fluid
at your earliest opportunity. (For instruc-
tions, see “Adding washer fluid” in Section
7 −3.)

’05 TUNDRA_U (L/O 0408)
180
2005 TUNDRA from Aug. ’04 Prod. (OM34427U)
CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light and low windshield
washer fluid level warning light)
1. Apply the parking brake.
2. Open one of the doors. The open door warning light should
come on.
3. Close the door. The open door warning light should go
off.
4. Turn the ignition key to “ON”, but do not start the engine.
All the service reminder indicators ex-
cept the open door warning light should
come on.
The following service reminder indica-
tors go off after a few seconds:
“ABS” warning light
“VSC TRAC” warning light
Low tire pressure warning light
Engine oil replacement reminder light
Roll sensing of curtain shield airbag off
indicator light
“AUTO LSD” indicator light
“VSC OFF” indicator light
(four −wheel drive models)
Slip indicator light
The SRS warning light goes off after
about 6 seconds.
There may be the case that the “ABS”
warning light (brake assist system
warning light), “VSC TRAC” warning
light, slip indicator light and “VSC OFF”
(four− wheel drive models) indicator light
stay on for about 60 seconds after the
ignition key is turned to the “ON” posi-
tion. It is normal if they go out after
a whi l e.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, have it checked by your Toyota
dealer as soon as possible.

’05 TUNDRA_U (L/O 0408)
343
2005 TUNDRA from Aug. ’04 Prod. (OM34427U)
GASOLINE CONTAINING MMT
Some gasoline contain an octane en-
hancing additive called MMT (Methylcy-
clopentadienyl Manganese Tricarbonyl).
Toyota does not recommend the use of
gasoline that contains MMT. If fuel con-
taining MMT is used, your emission con-
trol system may be adversely affected.
The Malfunction Indicator Lamp on the in-
strument cluster may come on. If this hap-
pens, contact your Toyota dealer for ser-
vice.
GASOLINE QUALITY
In a very few cases, you may experience
driveability problems caused by the partic-
ular gasoline that you are using. If you
continue to have unacceptable driveability,
try changing gasoline brands. If this does
not rectify your problem, then consult your
Toyota dealer.NOTICE
Do not use gasohol other than
stated above. It will cause fuel sys-
tem damage or vehicle performance
problems.
 If driveab ility problems occur ( poor
hot starting, vaporizing, engine
knock, etc.), discontinue the use.
 Take care not to spill gasohol dur-
ing refueling. Gasohol may cause
paint damage.
FUEL TANK CAPACITY
100 L (26.4 gal., 22.0 Imp. gal.) The fuel pump shut off system stops sup-
plying fuel to the engine to minimize the
risk of fuel leakage when the engine stalls
or an airbag inflates upon collision. To
restart the engine after the fuel pump shut
off system activates, turn the ignition
switch to “ACC” or “LOCK” once and start
it.
CAUTION
Inspect the ground under the vehicle
before restarting the engine. If you
find that liquid has leaked onto the
ground, it is the fuel system has
been damaged and it is in need of
repair. In this case, do not restart the
engine.
Fuel pump shut off system

’05 TUNDRA_U (L/O 0408)
420
2005 TUNDRA from Aug. ’04 Prod. (OM34427U)
Aluminum wheels: Use only a mild soap
or neutral detergent.
Plastic bumpers: Wash carefully. Do not
scrub with abrasive cleaners. The bumper
faces are soft.
Road tar: Remove with turpentine or
cleaners that are marked safe for painted
surfaces.
NOTICE
Do not use organic substances (gaso-
line, kerosene, benzine or strong sol-
vents), which may be toxic or cause
damage.
3. Rinse thoroughly—dried soap can
cause streaking. In hot weather you
may need to rinse each section right
after you wash it.
4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not
rub or press hard—you might scratch
the paint. Waxing your Toyota
Polishing and waxing is recommended
to maintain the original beauty of your
Toyota’s finish.
Apply wax once a month or if the vehicle
surface does not repel water well.
1. Always wash and dry the vehicle be- fore you begin waxing, even if you are
using a combined cleaner and wax.
2. Use a good quality polish and wax. If the finish has become extremely weath-
ered, use a car −cleaning polish, fol-
lowed by a separate wax. Carefully fol-
low the manufacturer’s instructions and
precautions. Be sure to polish and wax
the chrome trim as well as the paint.
3. Wax the vehicle again when water does not bead but remains on the sur-
face in large patches.
NOTICE
Always remove the plastic bumpers if
your vehicle is re −painted and placed
in a high heat paint waxing booth.
High temperatures could damage the
bumpers.
CAUTION
Vehicles with side airbags and cur-
tain shield airbags:
Be careful not to splash water or
spill liquid on the floor. This may
prevent the side airbags and curtain
shield airbags from activating cor-
rectly, resulting in serious injury.
Do not wash the vehicle floor with
water, or allow water to get onto
the floor when cleaning the vehicle
interior or exterior. Water may get
into audio components or other
electrical components above or un-
der the floor carpet (or mat) and
cause a malfunction; and it may
cause body corrosion.
Cleaning the interior

’05 TUNDRA_U (L/O 0408)
480
2005 TUNDRA from Aug. ’04 Prod. (OM34427U)
22. ALT− S 7.5 A: Charging system
23. ETCS 10 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system, electronic throttle control
system
24. HAZ 15 A: Emergency flashers, turn
signal lights, towing converter
25. EFI NO.1 20 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system, fuel pump, “EFI NO.2”
fuse
26. AM2 30 A: Ignition system, starting
system, “IGN” and “STA” fuses
27. TOWING 30 A: Towing converter
28. WIP 20 A: Windshield wipers and
washer
29. TURN 5 A: Turn signal lights
30. ECU IG 5 A: Anti−lock brake system,
vehicle stability control system, multi-
plex communication system, tire pres-
sure warning system
31. 4WD 20 A: Four−wheel drive control
system, A.D.D. control system
32. ACC 15 A: Cigarette lighter, audio sys-
tem, power rear view mirrors, “PWR
OUTLET 1” and “PWR OUTLET 2”
fuses 33. GAUGE 10 A:
Gauges and meters,
back −up lights, starting system, air
conditioning system, auto anti −glare in-
side rear view mirror, outside rear view
mirror heaters
34. IGN 5 A: SRS airbag system, multiport
fuel injection system/sequential multi-
port fuel injection system, discharge
warning light, ignition system, vehicle
stability control system, front passenger
occupant classification system
35. CARGO LP 5 A: Cargo lamp
36. TAIL 15 A: Tail lights, turn signal
lights, license plate lights, instrument
panel lights, parking lights, glove box
light
37. OBD 7.5 A: On−board diagnosis sys-
tem
38. HORN 10 A: Horns
39. STA 5 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system, g auges and meters
40. STOP 15 A: Stoplights, high mounted
stoplight, anti −lock brake system, ve-
hicle stability control system, towing
converter Fuses (type B)
41. AM1 40 A: Starting system, “ACC”,
“WIP”, “4WD”, “ECU −IG”, “GAUGE” and
“TURN” fuses
42. HTR 50 A: Air conditioning system,
“A/C” fuse
43. J/B 50 A: “POWER”, “CARGO LP”,
“TAIL”, “OBD”, “HORN” and “STOP”
fuses
44. ABS 2 50 A: Anti−lo
ck brake system,
v

ehicle stability control system
45. ABS 3 30 A: Anti−lock brake system,
vehicle stability control system
46. ST3 30 A: Starting system, “STA” fuse
47. POWER 30 A: Power door lock sys-
tem, power windows, power back win-
dow, power seat
Fuse (type C)
48. FL ALT 100 A (without towing pack- age) or 140 A (with towing package):
“AM1”, “HTR”, “J/B”, “MIR HTR”,
“FOG”, “TOW BRK”, “SUB BATT”,
“TOW TAIL”, “PWR OUTLET 1” and
“PWR OUTLET 2” fuses
49. A/PUMP 60 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system

’05 TUNDRA_U (L/O 0408)
483
2005 TUNDRA from Aug. ’04 Prod. (OM34427U)
43. STOP 15 A: Stop lights, high− mounted
stop lights, multiport fuel injection sys-
tem/sequential multiport fuel injection
system, anti −lock brake system, vehicle
stability control system, traction control
system, trailer light (stop lights), trailer
brake controller, towing converter, mul-
tiplex communication system
44. OBD 7.5 A: On−board diagnosis sys-
tem
45. PANEL 7.5 A: Instrument panel lights,
glove box light, lights of seat heaters,
cigarette lighter, ashtrays, multi −infor-
mation display, audio system/video sys-
tem, gauges and meters, air condition-
ing systems, power outlets
46. PWR NO.1 25 A: Driver ’s door lock
system, driver’s power wi ndow
47. WIP 25 A: Wiper and washers
48. IGN 1 10 A: Charging system, SRS
airbag system, multiport fuel injection
system/s equential multiport fuel injec-
tion system, vehicle stability control
system, g auges and meters, air condi-
tioning system, front passenger occu-
pant classification system
49. SUN ROOF 25 A: Electric moon roof50. PWR NO.2 25 A:
Front passengers’
door lock system, front passenger ’s
power window
51. HTR 10 A: Air conditioning systems,
electric cooling fan, back window de-
fogger, seat heaters
52. FOG 15 A: Front fog lights
53. GAUGE 15 A: Back−up lights, gauge
and meters, emergency flashers, slip
indicator light, vehicle stability control
system, four −wheel drive system, trailer
lights (back −up lights), multiport fuel
injection system/sequential multiport
fuel injection system, shift position indi-
cator lights
54. PWR OUTLET 15 A: Power outlets
55. SEAT HTR 15 A: Seat heaters
Fuses (type B)
56. MAIN 40 A: “H−LP RH”, “H −LP LH”
“H −LP LL” and “H −LP RL” fuses
57. DOOR NO.2 30 A: Multiplex commu-
nication system (power door lock sys-
tem, security system)
58. PWR SEAT 30 A: Power front seats59. AM1 40 A:
“HTR”, “CIG”, “GAUGE”,
“RAD NO.2”, “ECU −IG”, “WIP”, “WSH”,
“IGN 1”, “IGN 2” and “4WD” fuses
60. PWR NO.5 30 A: Power back window
Fuses (type D)
61. ABS NO.2 30 A: Anti−lock brake sys-
tem, vehicle stability control system
62. DEFOG 40 A: Back window defogger
63. HEATER 50 A: Air conditioning system
6 4

. TOWING R/B 60 A: “TOWING TAIL”,
“BATT CHARGE” and “TOWING BRK”
fuses
65. ALT 140 A: “DEFOG”, “ABS NO.2”,
“CARGO LP”, “HEATER”, “AM1”, “PWR
SEAT”, “TAIL”, “STOP”, “SUN ROOF”,
“PANEL”, “OBD”, “FOG”, “PWR NO.1”,
“PWR NO.2”, “PWR NO.5”, “AC INV”,
“PWR NO.3”, “PWR NO.4”, “PWR
OUTLET” and “SEAT HTR” fuses
66. ABS NO.1 40 A: Anti−lock brake sys-
tem, vehicle stability control system
67. A/PUMP 50 A: Multiport fuel injection
system/s equential multiport fuel injec-
tion system
68. R/B 30 A: “A/F” fuse