2005 TOYOTA TACOMA Owners Manual (in English)

11 92005 TACOMA from Mar. ’05 Prod. (OM35862U)
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the right passenger ’s seat-
ing position.
The anchorages are installed in the gap
between the seat cushion and seatback of
the right side of the seat as shown in the
illustration.
Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed to these anchorages. In this
case, it is not necessary to fix the child
restraint system with a seat belt on the
vehicle.
LS13160a
1st lock
position
10th lock
position
CHILD RESTRAINT SYSTEM
INSTALLATION 1. Separate seats only—Fold down the seatback and back to the 1st lock
position (most upright position) until
it locks into place. Adjust the seat-
back to the 10th lock position.
Make sure the seatback is locked secure-
ly.LS13080
Canada only
Ty p e A

1202005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13081
Canada only
Ty p e B
2. Widen the gap between the seat cushion and seatback slightly and
confirm the position of the lower an-
chorages near the button on the
seatback.
3. Type A—Latch the hooks of lower straps onto the anchorages and
tighten the lower straps.
Type B—Latch the buckles onto the
anchorages.
For owners in Canada— The symbol on
a child restraint system indicates the pres-
ence of a lower connector system.
If your child restraint system has a top
strap, it should be anchored. (For the
installation of the top strap, see “—Using
a top strap” on page 110 in this Section.)
For installation details, refer to the instruc-
tion manual equipped with each product.CAUTION
When using the lower anchorages
for the child restraint system, be
sure that there are no irregular ob-
jects around the anchorages or that
the seat belt is not caught.
Push and pull the child restraint
system in different directions to be
sure it is secure. Follow all the
installation instructions provided by
its manufacturer.
After securing the child restraint
system, never slide or recline the
seat.

1212005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13078
Front seat
LS13099
Rear seat
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the seat.
Front seat without seatback table—
The anchorages are installed in the gap
between the seat cushion and seatback of
the seat as shown in the illustration.
Front seat with seatback table—
The anchorages are installed in the seat
cushion of the seat.
Rear seat—
The anchorages are located at the base
of the seatback as shown in the illustra-
tion.
Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed to these anchorages. In this
case, it is not necessary to fix the child
restraint system with a seat belt on the
vehicle.
LS13160a
1st lock
position
10th lock
position
CHILD RESTRAINT SYSTEM
INSTALLATION 1. Front seat—Fold down the front seat seatback and back to the 1st lock
position (most upright position) until
it locks into place. Adjust the seat-
back to the 10th lock position.
Make sure the seatback is locked secure-
ly.
—Installation with child
restraint lower anchorages
(access cab models)

1222005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13082
Canada only
Front seat without seatback table (type A)
LS13083
Canada only
Front seat without seatback table (type B)
LS13186
Canada only
Front seat with seatback table (type A)

1232005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13187
Canada only
Front seat with seatback table (type B)
LS13100
Canada only
Rear seat (type A)
LS13101
Canada only
Rear seat (type B)

1242005 TACOMA from Mar. ’05 Prod. (OM35862U)
Front seat—2. Front seat without seatback table— Widen the gap between the seat
cushion and seatback slightly and
confirm the position of the lower an-
chorages near the button on the
seatback.
Front seat with seatback table—Wid-
en the slits of the seat cushion
slightly and confirm the position of
the lower anchorages near the but-
ton on the seat cushion.
3. Type A—Latch the hooks of lower straps onto the anchorages and
tighten the lower straps.
Type B—Latch the buckles onto the
anchorages.
Rear seat—
Type A—Latch the hooks of lower
straps onto the anchorages and tighten
the lower straps.
Type B—Latch the buckles onto the an-
chorages.
For owners in Canada— The symbol on
a child restraint system indicates the pres-
ence of a lower connector system. If your child restraint system has a top
strap, it should be anchored. (For the
installation of the top strap, see “—Using
a top strap” on page 113 in this Section.)
For installation details, refer to the instruc-
tion manual equipped with each product.
CAUTION
When using the lower anchorages
for the child restraint system, be
sure that there are no irregular ob-
jects around the anchorages or that
the seat belt is not caught.
Push and pull the child restraint
system in different directions to be
sure it is secure. Follow all the
installation instructions provided by
its manufacturer.
After securing the child restraint
system, never slide or recline the
seat.
Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupant(s) may be killed
or seriously injured in case of sud-
den braking or a collision.

1252005 TACOMA from Mar. ’05 Prod. (OM35862U)
LS13084
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the rear seat.
The anchorages are installed in the gap
between the seat cushion and seatback of
both outside rear seats as shown in the
illustration.
Child restraint systems complying with the
FMVSS213 or CMVSS213 specification
can be fixed with these anchorages. In
this case, it is not necessary to fix the
child restraint system with a seat belt on
the vehicle.LS13085
Canada only
Ty p e A
LS13086
Canada only
Ty p e B
—Installation with child
restraint lower anchorages
(double cab models)

1262005 TACOMA from Mar. ’05 Prod. (OM35862U)
CHILD RESTRAINT SYSTEM
INSTALLATION1. Widen the gap between the seat cushion and seatback slightly and
confirm the position of the lower an-
chorages near the button on the
seatback.
2. Type A—Latch the hooks of lower straps onto the anchorages and
tighten the lower straps.
Type B—Latch the buckles onto the
anchorages.
For owners in Canada— The symbol on
a child restraint system indicates the pres-
ence of a lower connector system.
If your child restraint system has a top
strap, it should be anchored. (For the
installation of the top strap, see “—Using
a top strap” on page 116 in this Section.)
For installation details, refer to the instruc-
tion manual equipped with each product.CAUTION
When using the lower anchorages
for the child restraint system, be
sure that there are no irregular ob-
jects around the anchorages or that
the seat belt is not caught.
Push and pull the child restraint
system in different directions to be
sure it is secure. Follow all the
installation instructions provided by
its manufacturer.
After securing the child restraint
system, never recline the seat.
Do not install a child restraint sys-
tem on the rear seat if it interferes
with the lock mechanism of the
front seats. Otherwise, the child or
front seat occupant(s) may be killed
or seriously injured in case of sud-
den braking or a collision.