2005 TOYOTA MATRIX brake

’05 MATRIX_U (L/O 0409)
276
2005 MATRIX from Sep. ’04 Prod. (OM12892U)
To check the fluid level, simply look at
the seethrough reservoir. The level
should be between the “MAX” and
“MIN” lines on the reservoir.
It is normal for the brake fluid level to go
down slightly as the brake pads wear. So
be sure to keep the reservoir filled.
If the reservoir needs frequent refilling, it
may indicate a serious mechanical prob-
lem.
If the level is low, add SAE J1703 or
FMVSS No.116 DOT 3 brake fluid to the
brake reservoir.Remove and replace the reservoir cap by
hand. Fill the brake fluid to the dotted
line. This brings the fluid to the correct
level when you put the cap back on.
Use only newly opened brake fluid. Once
opened, brake fluid absorbs moisture from
the air, and excess moisture can cause a
dangerous loss of braking.
CAUTION
Take care when filling the r
eservoir
because brake fluid can harm your
hands or eyes. If fluid gets on your
hands or in your eyes, flush the af-
fected area with clean water immedi-
ately. If you still feel uncomfortable
with your hands or eyes, go to the
doctor.
NOTICE
If you spill some of the fluid, be sure
to wipe it off to prevent it from dam-
aging the parts or paintwork.
If cold
O.K.
Close OpenIf hot
O.K.
If cold
add If hot
add
Check the fluid level through the reser-
voir. If necessary, add automatic trans-
mission fluid DEXRON
II or III.
If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little
more in frigid temperatures), the fluid is
hot (60 C—80 C or 140 F—175 F). You
may also check the level when the fluid
is cold (about room temperature,
10 C—30 C or 50 F—85 F) if the engine
has not been run for about five hours.
Checking brake fluid Checking power steering fluid

’05 MATRIX_U (L/O 0409)
285
2005 MATRIX from Sep. ’04 Prod. (OM12892U)
TIRE CHAIN SELECTION
Use the tire chains of correct size and
type.
Use SAE Class “S” type radial tire chains
except radial cable chains or V−bar type
chains.
Regulations regarding the use of tire
chains vary according to location or
type of road, so always check local reg-
ulations before installing chains.
CHAIN INSTALLATION
Install the chains on the front tires as
tightly as possible. Do not use tire
chains on the rear tires. Retighten
chains after driving 0.5—1.0 km
(1/4—1/2 mile).
When installing chains on your tires, care-
fully follow the instructions of the chain
manufacturer.
If wheel covers are used, they will be
scratched by the chain band, so remove
the covers before putting on the chains.CAUTION
Do not exceed 50 km/h (30 mph) or
the chain manufacturer ’s recom-
mended speed limit, whichever is
lower.
Drive carefully avoiding bumps,
holes, and sharp turns, which may
cause the vehicle to bounce.
Avoid sharp turns or lockedwheel
braking, as use of chains may ad-
versely affect vehicle handling.
When driving with chains installed,
be sure to drive carefully. Slow
down before entering curves to
avoid losing control of the vehicle.
Otherwise an accident may occur.
NOTICE
Do not attempt to use a tire chain on
the compact spare tire, as it may re-
sult in damage to the vehicle as well
as the tire.
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.
If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.
WHEEL SELECTION
When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.
This must be observed on compact spare
tire, too.
Correct replacement wheels are available
at your Toyota dealer.
A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis.
Replacing wheels

’05 MATRIX_U (L/O 0409)
305
2005 MATRIX from Sep. ’04 Prod. (OM12892U)
TRANSFER
(fourwheel drive models)
Oil capacity, L (qt., Imp. qt.):0.8 (0.8, 0.7)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity: Above −18 C (0 F)
SAE 90
Below −18 C (0 F)
SAE 85W or 85W −90
REAR DIFFERENTIAL
(fourwheel drive models)
Oil capacity, L (qt., Imp. qt.): 0.5 (0.5, 0.4)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity: Above −18 C (0 F)
SAE 90
Below −18 C (0 F)
SAE 85W or 85W −90 BRAKES
Minimum pedal clearance when depressed
with the force of 294 N (30 kgf, 66 lbf)
with the engine running, mm (in.):
Without anti −lock brake system
78 (3.07)
With anti −lock brake system
76 (2.99)
Pedal free play, mm (in.): 1—6 (0.04—0.24)
Pad wear limit, mm (in.): 1.0 (0.04)
Lining wear limit, mm (in.): 1.0 (0.04)
Parking brake adjustment when pulled with
the force of 196 N (20 kgf, 44 lbf): 5—8 clicks
Fluid type: SAE J1703 or FMVSS No.116 DOT 3
STEERING
Wheel free play: Less than 30 mm (1.2 in.)
Power steering fluid type: Automatic transmission fluid DEXRON II
or III

’05 MATRIX_U (L/O 0409)
308
2005 MATRIX from Sep. ’04 Prod. (OM12892U)
19. OBD 7.5 A: On−board diagnosis sys-
tem
20. WIPER 25 A: Windshield wipers
21. AM2 15 A: Charging system, multiport
fuel injection system/sequential multi-
port fuel injection system, starting sys-
tem, SRS airbag system
22. STOP 15 A: Stop lights, high mounted
stoplight, anti −lock brake system, shift
lock control system, multiport fuel in-
jection system/sequential multiport fuel
injection system, cruise control system
23. DOOR 25 A: Power door lock system,
glass hatch opener switch
24. AM1 25 A: “CIG” fuse
25. ECUIG 10 A: Electric cooling fan,
anti −lock brake system, traction control
system, vehicle stability control system,
brake assist system, shift lock control
system, cruise control system
26. RR WIPER 15 A: Rear window wiper
27. A/C 10 A: Air conditioning system
28. INV 15 A: Power outlet (115 VAC)
29. P/POINT 15 A: Power outlet (12 VDC/
in the rear console box)
30. ECUB 10 A: Daytime running light
system 31. CIG 15 A:
Power outlet (12 VDC/on
the instrument panel) or cigarette light-
er, car audio system, clock, shift lock
control system
32. GAUGE 10 A: Gauges and meters, air
conditioning system, daytime running
light system, charging system, auto
anti −glare inside rear view mirror, pow-
er windows, cruise control system, rear
window defogger, back −up lights, front
passenger ’s seat belt reminder light,
emergency flasher
33. WASHER 15 A: Windshield washer,
rear window washer
34. MHTR/DEF IUP 10 A: Engine control
system
Fuses (type B)
35. ABS NO.1 30 A: Anti−lock brake sys-
tem, traction control system, vehicle
stability control system, brake assist
system
36. RDI FAN 40 A: Electric cooling fan 37. ABS NO.2 40 A (without vehicle sta-
bility control system): Anti−lock brake
system
ABS NO.2 50 A (with vehicle stability
control system): Anti−lock brake sys-
tem, traction control system, vehicle
stability control system, brake assist
system
38. HEAD MAIN 40 A: “HEAD LH UPR”,
“HEAD RH UPR”, “HEAD LH LWR” and
“HEAD RH LWR” fuses
39. AIR PUMP 50 A (1ZZFE engine with fourwheel drive models and 2ZZGE
engine only): Emission control system
40. HTR 40 A: Air conditioning system
4

1. DEF 30 A: Rear window defogger,
“M −HTR/DEF I −UP” fuse
42. POWER 30 A: Power windows, electric
moon roof
Fuses (type C)
43. ALT 100 A: “ABS NO.1”, “ABS NO.2”,
“RDI FAN”, “FOG”, “HTR”, “AM1”,
“POWER”, “DOOR”, “ECU −B”, “TAIL”,
“STOP”, “P/POINT”, “INV” and “OBD”
fuses, charging system