Downloaded from www.Manualslib.com manuals search engine 11383K
INSPECTION AND MAINTENANCE
9-24
(18) 15A Front fog light fuse
(19) 30A Ignition switch fuse
(20) 50APower window, Ignition,
Wiper, Starter
(21)100A All Electrical Load
(22)100A ABS, MIL, Front fog
(23)100AEPS, Radiator Fan,
Heater, Starter Motor
(24) 50ALamp
(25)100A Glow
(26) 30A Blank
(27) 30A Blank
(28) – Blank
(29) 20A FI fuse
(30) – Blank
(31) 10A FI3 fuseThe main fuse, primary fuses and some of
the individual fuses are located in the
engine compartment. If the main fuse blows,
no electrical component will function. If a
primary fuse blows, no electrical component
in the corresponding load group will
function. When replacing the main fuse, a
primary fuse or an individual fuse, use a
MARUTI genuine replacement.
To remove a fuse, use the fuse puller pro-
vided in the fuse box. The amperage of
each fuse is shown in the back of the fuse
box cover.
w ww w
w WARNING
If the main fuse or a primary fuse
blows, be sure to have your vehicle
inspected by a MARUTI SUZUKI
authorized dealer. Always use a Maruti
Genuine replacement. Never use a
substitute such as a wire even for a
temporary repair, or extensive
electrical damage and a fire can result.NOTE:
Make sure that the fuse box always carries
spare fuses and fuse puller.EXAMPLEFuses under the Dash Board
83K-07-04983K-07-050
EXAMPLE
83K-07-048
Downloaded from www.Manualslib.com manuals search engine 11483K
INSPECTION AND MAINTENANCE
9-25(1) – Blank
(2) 15A Ignition coil
(3) 10A Back-up light
(4) 10A Meter
(5) 15A Accessory 1
(6) 15A Accessory 2
(7) 30A Power window
(8) 15A Wiper / Washer
(9) 10A IG1 SIG
(10) 15A Air bag
(11) 10A Anti-lock brake system
(12) 10ATail light
(13) – Blank
(14) 20A Door lock
(15) – Blank
(16) 10A ST SIG
(17) 10A Immobilizer
(18) 10A IG2 SIG
(19) 15A Rear fog light
(20) 15ARadio
(21) 20A Rear defogger
(22) 15A Horn / Hazard
(23) – Blank
(24) – BlankMAIN FUSE/PRIMARY FUSE
83K-07-051
The fuse box is located under the driver’s
side of the dashboard.
Remove the fuse box cover by pushing in
at both ends and pulling off the cover.
To remove a fuse, use the fuse puller pro-
vided in the fuse box.
83K-07-052
w ww w
w WARNING
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
V VV V
V
w ww w
w WARNING
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period
of time, you may have a major electri-
cal problem. Have your vehicle
inspected immediately by your
MARUTI SUZUKI authorized dealer.V VV V
V
Bulb Replacement Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially for
halogen headlight bulbs. Replace the
bulbs after they become cool
enough.
The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
w ww w
w WARNING
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
CAUTION
Downloaded from www.Manualslib.com manuals search engine 12383K
EMERGENCY SERVICE
10-2
2) Set the parking brake firmly and shift
into “R” (Reverse).
3) Turn on the hazard warning flasher if
your vehicle is near traffic.
4) Get down all the passengers.
5) Block the front and rear of the wheel
diagonally opposite of the wheel being
lifted.
6) Place the spare wheel near the wheel
being lifted as shown in the illustration
in case that the jack slips.
83K-08-00683K-08-007
CAUTION
Never jack up the vehicle with pas-
sengers inside the vehicle. 7) Position the jack vertically and raise the jack
by turning the jack handle clockwise until the
jack head recess fits the jacking point.
8) Continue to raise the jack slowly and
smoothly until the tyre clears the ground. Do
not raise the vehicle more than necessary.
w ww w
w WARNING
Use the jack only to change wheels
on level, hard ground.
Never jack up the vehicle on an
inclined surface.
Never raise the vehicle with the jack
in a location other than the specified
jacking point (shown in the illustration)
near the wheel to be changed.
Especially, do not raise the vehiclewith a jack at a part of the torsion
beam which is located under the
vehicle body, between rear wheels.
Make sure that the jack is raised at
least 51 mm (2 inches) before it
contacts the suspension arm boss.
Use of the jack when it is within 51
mm (2 inches) of being fully collapsed
may result in failure of the jack.
Never get under the vehicle when it
is supported by the jack.
Never run the engine when the
vehicle is supported by the jack and
never allow passengers to remain in
the vehicle.
V VV V
V
w ww w
w WARNING
V VV V
V
Changing WheelsTo change a wheel, use the following pro-
cedure:
1) Clear all passengers and luggage from
the vehicle.NOTE:
The jack and tools are located under the
spare wheel.2) Remove the jack, tools and spare wheel
from the vehicle.
3) Loosen, but do not remove the wheel
nuts.
4) Jack up the vehicle.
5) Remove the wheel nuts and wheel.
6) Before installing the new wheel, clean
any mud or dirt off from the surface of
83K-08-008
