2005 SUZUKI GRAND VITARA wheel torque

YH4
GRAND
VITARA
6. Shoe hold down
springs
7. Strut spring
8. Lower shoe return
spring 1. Upper shoe return spring
2. Adjuster
3. Pawl lever
4. Adjuster spring
5. Shoe hold down pins
1. Brake back plate
2. Cable cap
3. Brake cable
PARKING AND REAR BRAKE 5C-9
2) Install brake drum after making sure that inside of brake drum
and brake shoes are free from dirt and oil.
3) Upon completion of all jobs, depress brake pedal with about 30
kg (66 lbs) load three to ten times so as to obtain proper drum-to-
shoe clearance.
Adjust parking brake cable. (For adjustment, refer to PARKING
BRAKE CHECK AND ADJUSTMENT in Section 5.)
4) Tighten rear center console box screws.
5) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
6) Check to ensure that brake drum is free from dragging and prop-
er braking is obtained. Then remove vehicle from hoist and per-
form brake test (foot brake and parking brake).
BRAKE SHOE
REMOVAL
1) Perform steps 1) to 5) of BRAKE DRUM REMOVAL.
WARNING:
Use special care when installing brake shoe return
spring. Failure in its proper installation may allow it to
springback and cause personal injury.
2) Remove shoe hold down springs by turning shoe hold down
pins.
3) Remove upper return spring, struts, adjuster, adjuster lever and
springs.
4) Remove brake shoes and lower shoe return spring.
5) Remove brake shoes and disconnect parking brake cable from
parking brake shoe lever.

YH4
GRAND
VITARA
1. Wheel cylinder
1. Brake back plate
2. Brake pipe flare nut
3. Brake pipe
4. Wheel cylinder bolts1. Bleeder plug cap
5C-12 PARKING AND REAR BRAKE
WHEEL CYLINDER
REMOVAL
1) Perform steps 1) to 5) of BRAKE DRUM REMOVAL.
2) Perform steps 2) to 4) of BRAKE SHOE REMOVAL.
3) Loosen brake pipe flare nut (or nuts) but only within the extent
that fluid does not leak.
4) Remove wheel cylinder mounting bolts. Disconnect brake pipe
(or pipes) from wheel cylinder and put wheel cylinder bleeder
plug cap onto pipe to prevent fluid from spilling.
INSPECTION
Inspect wheel cylinder disassembled parts for wear, cracks, corro-
sion or damage.
NOTE:
Clean wheel cylinder components with brake fluid.
INSTALLATION (For non sealed type)
1) Take off bleeder plug cap from brake pipe and connect pipe (or
pipes) to wheel cylinder just enough to prevent fluid from leak-
ing.
2) Tighten wheel cylinder to brake back plate to specified torque.
Tightening Torque
(a): 8.5 N
.m (0.85 kg-m, 6.5 lb-ft)
3) Torque flare nut (or nuts) of brake pipe which was connected in
step 1) to specification.
Tightening Torque
(b): 16 N
.m (1.6 kg-m, 12.0 lb-ft)

YH4
GRAND
VITARA
2
1. Wheel cylinder
2. Gasket
1. Brake back plate
2. Brake pipe flare nut
3. Brake pipe
4. Wheel cylinder bolts
PARKING AND REAR BRAKE 5C-13
4) Install bleeder plug cap taken off from pipe back to bleeder plug.
5) For procedure hereafter, refer to steps 1) to 5) of BRAKE SHOE
INSTALLATION.
NOTE:
Be sure to bleed brake system. (for bleeding operation, re-
fer to BLEEDING BRAKES in Section 5.)
INSTALLATION (For gasket sealed type)
1) Install gasket to joint seam of wheel cylinder and brake back
plate. Then take off bleeder plug cap from brake pipe and con-
nect pipe (or pipes) to wheel cylinder just enough to prevent fluid
from leaking.
NOTE:
Be sure to check gasket for deterioration or any damage be-
fore installation and replace if found defective.
2) Tighten wheel cylinder to brake back plate to specified torque.
3) Torque flare nut (or nuts) of brake pipe which was connected in
step 1) to specification.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
(b): 16 N
.m (1.6 kg-m, 12.0 lb-ft)
4) Install bleeder plug cap taken off from pipe back to bleeder plug.
5) For procedure hereafter, refer to BRAKE SHOE INSTALLA-
TION.
NOTE:
Be sure to bleed brake system. Refer to ªCHECK AND AD-
JUSTMENTº in BRAKES section.

YH4
GRAND
VITARA
PARKING AND REAR BRAKE 5C-15
1. Rear axle shaft
2. Wheel bearing
3. Brake back plate1. Rear axle shaft
1. Rear axle
housing ªAº
INSTALLATION
1) Apply sealant to mating surface of bearing retainer with brake
back plate.
ªAº: Sealant 99000-31110
NOTE:
Make sure to remove old sealant before applying it anew.
2) Install brake back plate to rear axle shaft.
3) Apply sealant to joint seam of rear axle housing and brake back
plate.
ªAº: Sealant 99000-31110
NOTE:
Make sure to remove old sealant before applying it anew.
4) Install rear axle shaft to rear axle housing.
5) Tighten brake back plate nuts to specified torque.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
5C-16 PARKING AND REAR BRAKE
1. Brake back plate
2. Cable cap
3. Parking brake cable
6) Install wheel cylinder, and tighten wheel cylinder bolts and
brake pipe flare nut (or nuts) to specified torque. (Refer to steps
1) to 4) of WHEEL CYLINDER INSTALLATION of this section.)
7) Install parking brake cable to brake back plate.
8) Install brake shoes, referring to steps 1) to 4) of BRAKE SHOE
INSTALLATION.
9) Install brake drum. Refer to steps 1) to 2) of BRAKE DRUM
INSTALLATION in this section.
10) Refill differential housing with new specified gear oil. Refer to
ªMAINTENANCE SERVICEº in Section 7E for refill.
11) Fill reservoir with brake fluid and bleed brake system. (For
bleeding operation, refer to BLEEDING BRAKES in Section 5.)
12) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
13) Upon completion of all jobs, depress brake pedal with about 30
kg (66 lbs) load three to ten times so as to obtain proper drum-
to-shoe clearance.
Adjust parking brake cable. (For adjustment, refer to PARKING
BRAKE CHECK AND ADJUSTMENT in Section 5.)
14) Tighten rear center console box screws.
15) Check to ensure that brake drum is free from dragging and
proper braking is obtained. Then remove vehicle from hoist
and perform brake test (foot brake and parking brake).
16) Check each installed part for oil leakage.

YH4
GRAND
VITARA
PARKING AND REAR BRAKE 5C-17
09943-35512
Brake drum remover
(Front wheel hub remover)09942-15510
Sliding hammer
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Wheel cylinder bleeder plug7.50.755.5
Parking brake lever bolt232.317.0
Wheel cylinder bolt (For non sealed type)8.50.856.5
Wheel cylinder bolt (For gasket sealed type)111.112.0
Brake pipe flare nut161.612.0
Brake back plate nut232.317.0
Wheel nut10010.072.5
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.
Water tight
sealantSEALING COMPOUND 366E
99000-31090
To apply to mating surfaces of brake back
plate and rear wheel cylinder.
SealantSUZUKI BOND NO. 1215
99000-31110

To apply to mating surfaces of brake back
plate and rear axle housing.

To apply mating surfaces of brake back
plate and rear wheel bearing retainer.
SPECIAL TOOLS

YH4
GRAND
VITARA
Diagnostic Trouble Code (DTC) Table 5E1-14. . .
System Circuit 5E1-15. . . . . . . . . . . . . . . . . . . . . . .
Table ± A ªABSº Warning Lamp Circuit
Check ± Lamp does not come ªONº
at ignition switch on 5E1-16. . . . . . . . . . . . . . . . . .
Table ± B ªABSº Warning Lamp Circuit
Check ± Lamp comes ªONº steady 5E1-17. . . .
Table ± C ªABSº Warning Lamp Circuit
Check ± The lamp flashes continuously
while ignition switch is on5E1-18 . . . . . . . . . . . . . .
Table ± D Code (DTC) is not Outputted
even with Diag. Switch Terminal
Connected to Ground 5E1-19. . . . . . . . . . . . . . . .
Table ± E EBD Warning Lamp (Brake
Warning Lamp) Check-lamp Comes
ªONº Steady 5E1-20. . . . . . . . . . . . . . . . . . . . . . . .
DTC 15 ± G Sensor Circuit 5E1-21. . . . . . . . . . . .
DTC 21, 22, 25, 26, 31, 32, 35 or 36
± Wheel Speed Sensor Circuit 5E1-23. . . . . . . .
DTC 41, 45 or 56 ± Solenoid Circuit 5E1-26. . . . .
DTC 57 ± Solenoid and Pump Motor
Power Source Circuit 5E1-27. . . . . . . . . . . . . . . .
DTC 61 ± ABS Pump Motor Circuit 5E1-28. . . . . .
DTC 63 ± ABS Fail-Safe Relay Circuit 5E1-29. . .
DTC 71 ± ABS Control Module 5E1-30. . . . . . . . .
ON-VEHICLE SERVICE5E1-31 . . . . . . . . . . . . . . . .
Precaution 5E1-31. . . . . . . . . . . . . . . . . . . . . . . . . . .
ABS Hydraulic Unit Operation Check 5E1-31. . . .
ABS Hydraulic Unit / Control Module
Assembly 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic unit inspection 5E1-32. . . . . . . . . . . . . Removal 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-33. . . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Speed Sensor 5E1-34. . . . . . . . . . . .
Output voltage inspection 5E1-34. . . . . . . . . . . .
Removal 5E1-35. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-35. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-35. . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Front Sensor Rotor 5E1-36. . . . . . . . . . . . . . . . . . .
Removal 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Wheel Speed Sensor 5E1-37. . . . . . . . . . . .
Output voltage inspection 5E1-37. . . . . . . . . . . .
Removal 5E1-37. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-38. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-38. . . . . . . . . . . . . .
Installation 5E1-38. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Sensor Rotor 5E1-39. . . . . . . . . . . . . . . . . . . .
Removal 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . .
G Sensor 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Transfer 4WD Switch 5E1-41. . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5E1-41 . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5E1-42 . . . . . . . . . . . . . . . . . . . . . .
5E1-2 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
GENERAL DESCRIPTION
The ABS (Antilock Brake System) controls the fluid pressure applied to the wheel cylinder of each brake from the
master cylinder so that each wheel is not locked even when hard braking is applied. This ABS is a 4-wheel type
which controls the fluid pressure applied to the wheel cylinder of each of the four brakes to prevent each wheel
from getting locked.
The component parts of this ABS includes following parts in addition to those of the conventional brake system.

Wheel speed sensor which senses revolution speed of each wheel and outputs its signal.

In this ABS, ABS hydraulic unit (actuator assembly), ABS control module, pump motor relay and fail-safe relay
are combined as one component.

ABS control module which sends operation signal to ABS hydraulic unit to control fluid pressure applied to each
wheel cylinder based on signal from each wheel speed sensor so as to prevent wheel from locking.

ABS hydraulic unit which operates according to signal from ABS control module to control fluid pressure applied
to wheel cylinder of each of 4 wheels.

Fail-safe (solenoid valve) relay which supplies power to solenoid valve in ABS hydraulic unit and pump motor
relay.

Pump motor relay which supplies power to pump motor in ABS hydraulic unit.

ªABSº warning lamp which lights to inform abnormality when system fails to operate properly.

G sensor which detects body deceleration speed. (For 4WD model only)
This ABS is equipped with Electronic Brake force Distribution (EBD) system that controls a fluid pressure of rear
wheels to best condition, which is the same function as that of proportioning valve, by the signal from wheel sensor
independently of change of load due to load capacity and so on. And if the EBD system fails to operate properly,
the brake warning lamp lights to inform abnormality.

YH4
GRAND
VITARA
5E1-24 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
INSPECTION
STEPACTIONYESNO
11) Disconnect the applicable sensor connector with
ignition switch OFF.
2) Measure resistance between sensor terminals.
Resistance of wheel speed sensor:
1.2 ± 1.6 k
(at 20C, 68F)
3) Measure resistance between each terminal and
body ground.
Insulation resistance: 1M
or higher
Were measured resistance values in step 2) and 3)
as specified? (See Fig. 1)Go to step 2.Replace sensor.
21) Ignition switch OFF.
2) Disconnect connector from ABS hydraulic
unit / control module assembly. (See Fig. 2)
3) Check for proper connection to ABS hydraulic unit /
control module assembly at each sensor terminal.
4) If OK then, turn ignition switch ON and measure
voltage between sensor positive terminal of module
connector and body ground.
Is it 0 V?Go to step 3.Sensor positive
circuit shorted to
power.
31) Ignition switch OFF.
2) Connect connector to sensor.
3) Measure resistance between sensor terminals at
module connector.
4) Measure resistance between sensor positive
terminal and negative terminal of module connector,
between positive terminal and body ground.
Are measured resistance values within each specified
range described in above step 1?Go to step 4.Circuit open or
shorted to
ground.
41) Remove wheel speed sensor.
2) Check sensor for damage or foreign material being
attached.
Is it in good condition? (See Fig. 3)Go to step 5.Clean or replace
sensor.
5Check visually through wheel speed sensor
installation hole for following.

Rotor neither missing or damaged.

No foreign material being attached.

Rotor not being eccentric.

Wheel bearing free from excessive play.
Are they in good condition? (See Fig. 4)Go to step 6.Clean, repair or
replace.
61) Install sensor to knuckle or axle housing.
2) Tighten sensor bolt to specified torque and check
that there is not any clearance between sensor and
knuckle or axle housing. (See Fig. 5)
Replace sensor if any.
Referring to item OUTPUT VOLTAGE INSPECTION of
FRONT WHEEL SPEED SENSOR, check output voltage
or waveform of sensor. Is proper output voltage or
waveform obtained?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.Replace sensor
and recheck.