2005 SUZUKI GRAND VITARA gauge

YH4
GRAND
VITARA
5-18 BRAKES
09950-78220
Flare nut wrench (10 mm)09900-20205
Micrometer (0 ± 25 mm)09956-02310
Fluid pressure gauge09956-02210
Brake circuit plug
09952-36310 / 09952-46510
Pressure gauge attachment
SPECIAL TOOLS

YH4
GRAND
VITARA
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-19
09922-85811
Connector pin remover09950-96010
Booster piston rod gauge09952-16010
Booster piston rod adjuster
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake flexible hose bolt (Brake caliper / 2 (4) way joint)232.317.0
Master cylinder attaching nut131.39.5
Booster nut131.39.5
Clevis nut252.518
2-way (or 4-way) joint mounting bolt101.07.5
Brake pipe flare nut161.611.5
Front caliperM88.00.86.0
Brake bleederplug
Front cali erM108.50.856.5Brake bleeder lugWheel cylinder7.50.755.5
LSPV8.00.86.0
LSPV mounting bolt
LSPV stay bolt232.317.0
LSPV spring nut
Wheel nut10010.072.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.
SPECIAL TOOLS

YH4
GRAND
VITARA
FRONT BRAKE 5B-7
2) Remove piston seal using a thin blade like a thickness gauge,
etc.
CAUTION:
Be careful not to damage inside (bore side) of cylinder.
INSPECTION
Cylinder Boot
Check boots for breakage, crack and damage. If defective, replace.
Piston Seal
Excessive or uneven wear of pad lining may indicate unsmooth re-
turn of the piston. In such a case, replace rubber seal.
ASSEMBLY
Reassemble front brake in reverse order of disassembly, noting the
following points.
CAUTION:

Wash each part cleanly before installation in the same
fluid as the one used in master cylinder reservoir.

Never use other fluid or thinner.

Before installing piston and piston seal to cylinder, apply
fluid to them.

After reassembling brake lines, bleed air from them.
Piston Seal
Piston seal is used to seal piston and cylinder and to adjust clear-
ance between pad and disc. Replace with a new one at every over-
haul. Fit piston seal into groove in cylinder taking care not to twist
it.

YH4
GRAND
VITARA
1. Fluid pressure check hole
2. Oil pan
1. Oil pan
2. Exhaust pipe
7B1-54 AUTOMATIC TRANSMISSION (4 A / T)
LINE PRESSURE TEST
Purpose of this test is to check operating conditions of each part by
measuring fluid pressure in fluid pressure line. Line pressure test
requires following conditions.

Automatic fluid is at normal operating temperature (70 to 80C /
158 ± 176F).

Fluid is filled to proper level (between FULL HOT and LOW HOT
on dipstick).
1) Apply parking brake securely and place checks against wheels.
2) Attach oil pressure gauge to fluid pressure check hole in trans-
mission case.
Special Tool
(A): 09925-37810
CAUTION:
After attaching oil pressure gauge, check that not fluid
leakage exists.
3) Depress foot brake fully, run engine at idle and stall and then
check fluid pressure in ªDº or ªRº range.
CAUTION:
Do not continue running engine at stall speed longer than
5 seconds.
G16 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
5.1 ± 5.7 kg / cm2
73 ± 81 psi
At stall speed11.7 ± 13.2 kg / cm2
166 ± 188 psi
14.2 ± 16.7 kg / cm2
202 ± 237 psi
J20 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.8 ± 4.3 kg / cm2
54 ± 61 psi
5.3 ± 5.9 kg / cm2
75 ± 84 psi
At stall speed9.7 ± 11.2 kg / cm2
138 ± 159 psi
12.9 ± 15.5 kg / cm2
183 ± 220 psi
H25 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
6.6 ± 7.2 kg / cm2
94 ± 102 psi
At stall speed11.3 ± 12.7 kg / cm2
161 ± 181 psi
14.7 ± 22.7 kg / cm2
209 ± 323 psi

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-79
09925-37810
Oil pressure gauge09927-56010
Gear stopper
(only for G16 / J20)09931-76030
16 / 14 pin DLC
(OBD-II adapter) cable
09931-76011
SUZUKI scan tool (Tech 1A) kit1. Storage case
2. Operator's manual
3. Tech 1A
4. DLC cable
5. Test lead / probe
6. Power source cable
7. DLC cable adapter
8. Self±test adapterMass storage cartridge
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
A / T fluidAn equivalent of DEXRON-III
Automatic transmission

Parts lubrication when installing
Lithium greaseSUZUKI SUPER GREASE A
(99000±25010)
Cable ends
SealantSUZUKI BOND NO.1215
(99000-31110)
Flywheel bolts
SPECIAL TOOLS

YH4
GRAND
VITARA
7E-10 DIFFERENTIAL (FRONT)
1. Plugged hose
2. Adjusting screw
3. Pipe (to air pump assembly)
4. Hose (to differential carrier)
5. Differential housing
4 5
INSPECTION
4WD Control System
1) Install special tool to air hose connecting between air pump as-
sembly and differential (actuator) as shown in figure. Tighten ad-
justing screw of special tool as far as it stops. Close air check
side opening by using fuel hose as blind plug.
Special Tool
(A): 09918-18110
(B): 09367-04002
NOTE:
Use care not to bend any part of hose.
2) Turn ON ignition switch and shift transfer lever from 2H to 4H
range.
3) Check that motor starts running (a sound can be heard) within
1 second and it stops when gauge of special tool indicates speci-
fied pressure value.
Check also for air leakage.
Pressure specification:
30.0 ± 45.0 kPa (0.30 ± 0.45 kg / cm
2, 4.25 ± 6.40 psi)
4) Check that pressure value indicated on gauge of special tool
drops as soon as transfer lever is shifted to 2H position.
5) Start motor by shifting transfer lever to 4H position again. Loos-
en adjusting screw to lower pressure value on gauge. Motor
should start to run again and stop in about 4 seconds.
6) With the adjusting screw of special tool loosened, shift transfer
shift lever to N or 2H position and then 4L or 4H position.
Pump motor should stop about 10 seconds after motor starts to
run.

YH4
GRAND
VITARA
8C
INSTRUMENTATION / DRIVER INFORMATION 8C-1
GENERAL DESCRIPTION8C- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8C- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8C- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8C- 2. . . . . . . . . . . . . . . . .
Abbreviations 8C- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8C- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8C- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8C- 2. . . . . . . . . . . . . . . .
Combination Meter 8C- 2. . . . . . . . . . . . . . . . . . .
DIAGNOSIS8C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 4. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 4. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C- 4. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Remainder Warning Buzzer 8C- 5. . . . . . . Seat Belt Warning Light (If Equipped) 8C- 5. . .
Ignition Key Remainder Warning
Buzzer (If Equipped) 8C- 5. . . . . . . . . . . . . . . . .
Cigarette Lighter and Accessory Socket 8C- 5.
ON-VEHICLE SERVICE8C- 6 . . . . . . . . . . . . . . . .
Ignition (Main) Switch 8C- 6. . . . . . . . . . . . . . . . .
Combination Meter 8C- 7. . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 8. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 9. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C-11. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Key Remainder (If Equipped) /
Light Remainder Warning Buzzer 8C-12. . . . . .
Door Switch 8C-13. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Warning Light (If Equipped) 8C-13. . .
SECTION 8C
INSTRUMENTATION/DRIVER INFORMATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
1. To door switch (driver side) B / Bl
2. To transmission range switch G / Bl
(A / T vehicle only, if equipped) L
3. To transmission range switch G / O
(A / T vehicle only, if equipped) 2
4. To transmission range switch Y / G
(A / T vehicle only, if equipped) D
5. To transmission range switch O / Bl
(A / T vehicle only, if equipped) N
6. To transmission range switch O / G
(A / T vehicle only, if equipped) P
7. To transmission range switch R
(A / T vehicle only, if equipped) R
8. To ground B
9. To PCM (A / T vehicle only) W / B
10. To ECT sensor Y / W
11. To fuel level gauge Bl / W
12. To ground B / Y
13. To combination switch G / Y
NOTE:
Terminal arrangement of coupler viewed from harness side.
Coupler A Coupler B Coupler C
Coupler A Coupler B Coupler C
1. Blank ÐÐ
2. Blank ÐÐ
3. To ignition switch B / W
4. Blank ÐÐ
5. To ABS control module Bl / O
(if equipped)
6. To PCM (A / T vehicle only) Gr / Bl
7. To ABS control module Br
(if equipped)
8. To VSS Bl / Y
9. To combination switch G / R
10. To SDM (if equipped) Y / G or Bl
11. To main fuse W / Bl
12. To fuse box W
13. To combination switch R
14. To ECM (PCM for A / T vehicle) V
(if equipped)
15. To ECM (PCM for A / T vehicle) V / Y
16. To ECM (PCM for A / T vehicle) O / B
(if equipped)1. To ground B
2. To ECM (PCM for A / T vehicle) Br
3. To ignition switch (if equipped) V / R
4. To brake fluid level switch R / B
5. To parking brake switch V
6. To seat belt switch (if equipped) Gr / R
7. To generator W / R
8. To oil pressure switch Y / B
9. To combination switch R / Y
10. To ignition switch (if equipped) Bl / R or CHECK
or ENGINE
or ABSif equipped
if equippedif equipped
INSTRUMENTATION / DRIVER INFORMATION 8C-3