2005 SUZUKI GRAND VITARA lock

YH4
GRAND
VITARA
1. Yellow connector of passenger air bag (inflator) module
2. Steering support member
3. Air bag harness
AIR BAG SYSTEM 10B-57
3) Connect Yellow connector of passenger air bag (inflator) mod-
ule, and be sure to lock connector with lock lever.
ii) Connect connector.
ii) Lock connector with lock lever.
4) Install glove box.
5) Install ªAIR BAGº fuse to ªAIR BAGº fuse box.
6) Turn ignition switch to ON and verify that ªAIR BAGº warning
lamp flashes 6 times and then turns off.
If it does not operate as described, perform ªAir Bag Diagnostic
System Checkº in this section.
HANDLING AND STORAGE
SDM
WARNING:
Never power up air bag system when SDM is not rigidly at-
tached to the vehicle. Otherwise, personal injury may result.
CAUTION:
After detecting one time of such collision as to meet deploy-
ment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.

Never attempt disassembly of SDM.

When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.

If SDM was dropped from a height of 90 cm (3 ft) or more or if it
is found to be damaged or deformed, replace it with a new one.

If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.

All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the ve-
hicle to ensure proper operation of the air bag system.

YH4
GRAND
VITARA
1. SDM
2. SDM connector
3. SDM plate
4. SDM cover
1. Air bag wire harness
2. Ground
3. SDM case ground
AIR BAG SYSTEM 10B-65

Passenger air bag (inflator) module
± Check for dents, cracks, damage or fitness.
± Check trim cover for cracks or deformities.
± Check harness and connector for damage or tightness.
If any faulty condition is found in above checks, replace.

SDM and SDM plate
± Check for external damage such as deformation, scratch,
crack, peeled paint, etc.
± Check whether SDM can installed properly due to a cause in it-
self. (There is a gap between SDM and SDM plate, or it cannot
be fixed securely.)
± Check whether connector or lead wire of SDM has a scorching,
melting or damage.
± Check whether connector can be connected securely or locked.
± Check SDM connector and terminals for tightness.
± Check SDM sets a diagnostic trouble code and the diagnostic
table leads to a malfunctioning SDM.
If any faulty condition is found in above checks, replace.

Air bag wire harness and connections
± Check for damages, deformities or poor connections.
(Refer to ªIntermittent And Poor Connectionsº in this section.)
± Check wire harness clamps for tightness.
If any faulty condition is found, correct or replace.

YH4
GRAND
VITARA
1. SDM
2. SDM bolt
3. SDM cover
4. SDM connector1. Front center console box
2. Center garnish panel
3. Ashtray
4. Radio hole cover
5. Clock assembly
AIR BAG SYSTEM 10B-67
SDM
WARNING:
During service procedures, be very careful when handling
a Sensing and Diagnostic Module (SDM).
Be sure to read ªService Precautionsº in this section before
starting to work and observe every precaution during work.
Neglecting them may result in personal injury or inactiva-
tion of the air bag system when necessary.
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº ear-
lier in this section.
3) Remove rear and front center console box by removing screw
and clips.
4) Remove center garnish panel.
5) Remove ashtray and tuner assembly, clock assembly, tuner
pocket, radio hole cover, etc.
6) Disconnect SDM connector from SDM.
7) Remove SDM (with SDM plate) as an assembly from vehicle.
NOTE:
Do not separate SDM and SDM plate.
INSPECTION
CAUTION:

Do not connect a tester whatever type it may be.

Never repair or disassemble SDM.

If SDM was dropped from a height of 90 cm (3 ft) or more,
it should be replaced.

Check SDM and SDM plate for dents, cracks or deformation.

Check SDM connector for damage, cracks or lock mechanism.

Check SDM terminal for bent, corrosion or rust.
If any faulty condition is found in above checks, replace.

YH4
GRAND
VITARA
1. SDM
2. SDM bolt
3. SDM cover
4. SDM connector
5. Arrow
1. Front center console box
2. Center garnish panel
3. Ashtray
4. Radio hole cover
5. Clock assembly
10B-68 AIR BAG SYSTEM
INSTALLATION
1) Check that none of following faulty conditions exists.

Bend, scratch, deformity in vehicle body mounted on SDM

Foreign matter or rust on mating surface of vehicle body
mounted on SDM
2) Install SDM (with SDM plate) to vehicle.
CAUTION:
Ensure that arrow on the SDM is pointing toward the front
of the vehicle.
3) Tighten SDM bolts to specified torque.
Tightening Torque
(a): 6.0 N´m (0.6 kg-m, 4.5 lb-ft)
4) Connect SDM connector to SDM securely.
5) Install tuner assembly, clock assembly, tuner pocket, radio hole
cover, etc. and ashtray.
6) Install center garnish panel.
7) Install front and rear center console box.
8) Connect negative cable to battery.
9) Enable air bag system. Refer to ªEnabling Air Bag Systemº earli-
er in this section.

YH4
GRAND
VITARA
1. Shorted
1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket
ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.
ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.
10B-72 AIR BAG SYSTEM
1) Turn ignition switch to ªLOCKº, remove key and put on safety
glasses.
2) Check that there is no open, short or damage in special tool (de-
ployment harness). If any faulty is found, do not use it and be
sure to use new deployment harness.
Special Tool
(A): 09932-75030
3) Short the two deployment harness leads together by fully seat-
ing one banana plug into the other.
WARNING:
Deployment harness shall remain shorted and not be
connected to a power source until the air bag is to be
deployed.
Special Tool
(A): 09932-75030
4) Remove driver or passenger air bag (inflator) module from ve-
hicle, referring to SECTION 3C1 or 10B.
WARNING:

Always carry live air bag (inflator) module with trim cov-
er away from you.

When storing a live air bag (inflator) module or when
leaving a live air bag (inflator) module unattended on a
bench or other surface, always face the bag and trim
cover up and away from the surface. As the live passen-
ger air bag (inflator) module must be placed with its bag
(trim cover) facing up, place it on the workbench with
a slit or use the workbench vise to hold it securely at its
lower mounting bracket.
This is necessary so that a free space is provided to al-
low the air bag to expand in the unlikely event of acci-
dental deployment.
Failure to follow procedures may result in personal inju-
ry.
5) Temporarily place driver or passenger air bag (inflator) module
on the workbench or the vise according to above WARNING.

YH4
GRAND
VITARA
4
31
2
2
4
31
For driver air bag (inflator) module
For passenger air bag (inflator) module
1. Stretch deployment harness to full length 10 m (33 ft).
2. Connect connectors.
3. Power source (12V vehicle battery).
4. Short the two deployment harness leads.
10B-74 AIR BAG SYSTEM
7) Stretch the deployment harness from the driver or passenger
air bag (inflator) module to its full length 10 m (33 ft).
8) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
9) Verify that the area around the driver or passenger air bag (in-
flator) module is clear of all people and loose or flammable ob-
jects.
10) [In case of Driver Air Bag (Inflater) Module]
Verify that the driver air bag (inflator) module is resting with its
vinyl trim cover facing up.
[In case of Passenger Air Bag (Inflator) Module]
Verify that the passenger air bag (inflator) module is firmly and
properly secured in passenger air bag (inflator) module deploy-
ment fixture (special tool).
11) Connect the driver or passenger air bag (inflator) module to the
deployment harness connector and lock connector with lock le-
ver.
12) Notify all people in the immediate area that you intend to deploy
the air bag (inflator) module.
NOTE:

When the air bag deploys, the rapid gas expansion will
create a substantial report. Wear suitable ear protection.
Notify all people in the immediate area that you intend to
deploy the air bag (inflator) module and suitable ear
protection should be worn.

When the air bag deploys, the driver air bag (inflator)
module may jump about 30 cm (1 ft) vertically. This is a
normal reaction of the driver air bag (inflator) module to
the force of the rapid gas expansion inside the air bag.

After the air bag (inflator) module has been deployed, the
surface of the air bag may contain a powdery residue.
This powder consists primarily of cornstarch (used to lu-
bricate the bag as it inflates) and byproducts of the
chemical reaction.

YH4
GRAND
VITARA
10B-78 AIR BAG SYSTEM
DEPLOYMENT INSIDE VEHICLE
Use this procedure when scrapping the entire vehicle including the driver and passenger air bag (inflator) modules.
CAUTION:
When vehicle itself will be used again, deploy the air bag outside vehicle according to ªDeployment
Outside Vehicleº, for deploying it inside will cause the instrument panel, glove box and their vicinity
to be deformed.
Failure to observe this CAUTION may require unneeded vehicle inspection and repair.
WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.

To avoid an accidental deployment, this work should be performed by no more than one person.

The procedure should be followed strictly as described here.

Be sure to read ªService Precautionsº for the air bag (inflator) module beforehand.

Never connect deployment harness to any power source before connecting deployment harness to
the air bag (inflator) module. Deployment harness shall remain shorted and not be connected to a
power source until the air bag is to be deployed.

The air bag (inflator) module will immediately deploy the air bag when a power source is connected
to it. Wear safety glasses throughout this entire deployment and disposal procedure.

Wear suitable ear protection when deploying air bag. Also, advise those who are in the area close to
deployment site to wear suitable ear protection.

Do not deploy driver and passenger air bag (inflator) modules at the same time.
1) Turn ignition switch to ªLOCKº, remove key and put on safety
glasses.
2) Remove all loose objects from front seats and instrument panel.
3) [For driver air bag (inflator) module]
Disconnect contact coil connector (yellow connector) located
near the base of the steering column.
ii) Release locking of lock lever.
ii) After unlocked, disconnect to connector.
[For passenger air bag (inflator) module]
Remove glove box from instrument panel and disconnect pas-
senger air bag (inflator) module connector (yellow connector).
ii) Release locking of lock lever.
ii) After unlocked, disconnect to connector.

YH4
GRAND
VITARA
1. Shorted
For driver air bag (inflator) module
1. Short deployment harness leads
AIR BAG SYSTEM 10B-79
4) Confirm that each air bag (inflator) module is securely mounted.
5) Check that there is no open/short or damage in special tool (de-
ployment harness). If any faulty condition is found, do not use it
and be sure to use new deployment harness.
Special Tool
(A): 09932-75030
6) Short the two deployment harness leads together by fully seat-
ing one banana plug into the other.
WARNING:
Deployment wires shall remain shorted and not be con-
nected to a power source until the air bag is to be
deployed.
Special Tool
(A): 09932-75030
7) Connect deployment harness connector to air bag (inflator)
module (driver or passenger) and lock connector with lock lever.
Special Tool
(A): 09932-75030