2005 SUZUKI GRAND VITARA lock

YH4
GRAND
VITARA
9-20 BODY SERVICE
1. Sealing cover
2. Adhesive
INSTALLATION
Reverse removal procedure to install back door / rear gate noting
following points.

Secure wiring harness.

Secure back door / rear gate sealing cover.
NOTE:
Use adhesive to seal sealing cover to back door / rear gate.

Adjust back door / rear gate latch striker position by referring
ªBACK DOOR LOCK ASSEMBLY INSTALLATIONº so that back
door / rear gate is positioned correctly.

Adjust back door / rear gate cushion so that back door / rear gate
contacts body when closed.

YH4
GRAND
VITARA
BODY SERVICE 9-21
1. Hood lock
2. Hood lock bolts
3. Match marks
1. Hood cushion
HOOD
REMOVAL
1) Remove window washer hose from hood.
2) Remove four mounting bolts to detach hood.
ADJUSTMENT

Fore-and-aft and right-and-left adjustment.
Loosen four mounting bolts for adjustment.

Hood lock adjustment
When installing hood lock, bring bolt at intersection point of match
marks and move it in vertical direction for adjustment, if neces-
sary.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)

Vertical adjustment
If only one side (right or left) of hood is not level with front fender,
make it level by tightening or loosening hood cushion.
INSTALLATION
Reverse removal procedure to install hood.
INSPECTION
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.) Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.

YH4
GRAND
VITARA
1. Seat cushion
2. Seat back
3. Seat auto lock release handle
4. Seat hinge male
5. Hinge male cover
BODY SERVICE 9-35
REAR SEAT
REMOVAL
1) Remove four mounting bolt to remove seat cushion.
2) Remove four mounting bolts to remove seat back.
3) Disassemble and repair seat as necessary.
INSTALLATION
Reverse removal procedure to install rear seat.
Torque to specifications, as shown.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)

YH4
GRAND
VITARA
BODY SERVICE 9-59
1. Door latch
2. Outside handle
3. Inside handle bezel
4. Latch striker
1. Door opening control rod pin retainer
2. Door opening control rod
3. Door lock control rod
3
SECURITY AND LOCKS
FRONT DOOR LOCK ASSEMBLY
REMOVAL
1) Raise window all the way up.
2) Remove door trim and door sealing cover, refer to steps 1) to 6)
of FRONT DOOR GLASS REMOVAL in this section.
3) Remove door opening control rods.
Unlock door lock rod pin retainer and disconnect control rod.
4) Remove door lock control rod.
5) Disconnect door lock motor lead wire (if equipped).
6) Remove lock assembly.

YH4
GRAND
VITARA
9-60 BODY SERVICE
1. Door latch
2. Door latch striker
3. Shaft
1. Door latch striker
2. Body
3. Door4. Front side
5. Shim
INSTALLATION
To install front door lock, reverse removal procedure, noting follow-
ing.

Door latch striker.
Move door latch striker up or down so its center aligns with the
center of groove ªAº on the door, as shown.
NOTE:
Striker should be moved vertically and placed level. Do not
adjust door lock.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)

Move door latch striker sideways to adjust door surface flush with
body surface, as shown.
In order to correctly obtain door latch striker position in the fore-
and-aft direction, increase or decrease number of shims inserted
between body and striker to adjust it.
Dimension ªaº: 10.9 ± 12.9 mm (0.43 ± 0.5 in.)
ªbº: 3.4 ± 5.4 mm (0.13 ± 0.21 in.)
NOTE:
Apply oil or grease to striker joints periodically.

YH4
GRAND
VITARA
BODY SERVICE 9-61
1. Outside handle
2. Inside handle bezel
3. Latch assembly
4. Latch striker
1. Door opening rod pin
2. Door opening control rod
REAR DOOR LOCK ASSEMBLY
REMOVAL
1) Remove door trim and door sealing cover, refer to steps 1) to 4)
of REAR DOOR GLASS REMOVAL in this section.
2) Remove door opening control rod and door lock control rod.
3) Remove lock assembly.
INSTALLATION
Reverse removal sequence to install rear door lock, noting points
mentioned in ªFRONT DOOR LOCK ASSEMBLYº.

YH4
GRAND
VITARA
1. Shim
1. Rubber cushion 1
9-62 BODY SERVICE
BACK DOOR / REAR GATE LOCK ASSEMBLY
REMOVAL
1) Remove inside handle bezel (if equipped).
2) Remove inside lock knob.
3) Remove door trim.
With inside handle bezel tilted as shown in figure, turn door trim
90 counterclockwise to remove it (if equipped with inside han-
dle).
4) Remove back door / rear gate sealing cover.
5) Remove back door / rear gate lock control rod.
Unlock back door / rear gate lock rod pin retainer and disconnect
control rod.
6) Disconnect back door lock motor lead wire (if equipped).
7) Remove lock assembly.
INSTALLATION
Reverse removal procedure to install back door / rear gate lock as-
sembly noting following points.

Back door / Rear gate latch striker.
Adjust back door / rear gate latch striker so that its center aligns
with the center of groove in back door / rear gate latch base.
To adjust back door / rear gate latch and striker with each other,
insert proper number of shims below the bottom of striker, as
shown.

Back door / Rear gate rubber cushion.
Move rubber cushion installed at the left side of back door / rear
gate to align it with its guide.

YH4
GRAND
VITARA
BODY SERVICE 9-63
KEY CODING
KEY USAGE AND IDENTIFICATION
Key is used for ignition and door lock cylinder. Keys are cut on both
edges to make them reversible.
Key identification is obtained from five character key code stamped
on key code tag. Using this key code, key code cutting combination
can be determined from a code list (available to owners of key cut-
ting equipment from suppliers).
If key codes are not available from records or tags, key code can
be obtained from the right hand door lock cylinder (if lock has not
been replaced). Lock cylinders supplied by the factory as service
parts are unmarked.
If original key is available, key code cutting combination can be de-
termined by laying key.
IGNITION SWITCH LOCK CYLINDER
Removal / Installation
See Section 3C1, ªAIR BAG STEERING WHEEL AND COLUMNº.
ELECTRICAL DIAGNOSIS
For ignition switch electrical troubleshooting, see Section 8, ªBODY
ELECTRICAL SYSTEMº.