2005 SUZUKI GRAND VITARA Air con

YH4
GRAND
VITARA
5E1-30 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
DTC 71 (DTC C1071) ± ABS CONTROL MODULE
DESCRIPTION
This DTC will be set when an internal fault is detected in the ABS control module.
INSPECTION
STEPACTIONYESNO
11) Ignition switch OFF.
2) Disconnect connectors from ABS control module.
3) Check for proper connection to ABS control
module at all terminals.
Are they in good condition?Substitute a
known-good ABS
control module and
recheck.Repair or replace.

YH4
GRAND
VITARA
5E1-32 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. ABS hydraulic
unit /control
module
assembly
2. Brake pipe
1. ABS hydraulic
unit / control
module connector 1. Brake pipe
2. ABS hydraulic unit /
control module assembly
3. Bracket
ABS HYDRAULIC UNIT / CONTROL MODULE
ASSEMBLY
CAUTION:
Never disassemble ABS hydraulic unit / control module as-
sembly, loosen blind plug or remove motor. Performing any
of these prohibited services will affect original performance
of ABS hydraulic unit / control module assembly.
HYDRAULIC UNIT INSPECTION

Check hydraulic unit for fluid leakage.
If any, repair or replace.
REMOVAL
1) Disconnect negative cable at battery.
2) Using special tool, disconnect brake pipes from ABS hydraulic
unit / control module assembly and loosen flare nuts as shown
figure.
Special Tool
(A): 09950-78220
NOTE:
Put bleeder plug cap onto pipe to prevent fluid from spilling.
Do not allow brake fluid to get on painted surfaces.
3) Disconnect ABS hydraulic unit / control module assembly con-
nector.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-33
1. ABS hydraulic unit /
control module
assembly
2. Nut
1. To left-front
2. To right-front
3. To rear
4. From master cylinder4) Remove three nuts and take out ABS hydraulic unit / control
module assembly from bracket.
CAUTION:

Do not give an impact to hydraulic unit.

Use care not to allow dust to enter hydraulic unit.

Do not place hydraulic unit on its side or upside down.
Handling it in inappropriate way will affect its original
performance.
INSTALLATION
1) Install hydraulic unit by reversing removal procedure.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 12.0 lb-ft)
(b): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
(c): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
2) Bleed air from brake system. Refer to ªBLEEDING BRAKESº in
Section 5.
3) Check each installed part for fluid leakage and perform hydraulic
unit operation check.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-35
FORWARD
1. Front wheel speed
sensor connector
2. Headlight assembly
1. Front wheel speed sensor
2. Bolt
REMOVAL
1) Disconnect negative cable at battery.
2) Hoist vehicle and remove wheel.
3) Disconnect front wheel speed sensor connector.
4) Remove harness clamp bolts and remove front wheel speed
sensor from knuckle.
CAUTION:

Do not pull wire harness when removing front wheel
speed sensor.

Do not cause damage to surface of front wheel speed
sensor and do not allow dust, etc. to enter its installa-
tion hole.
SENSOR INSPECTION

Check sensor for damage.

Check sensor for resistance.
Resistance between terminals: 1.2 ± 1.6 k
at 20C (68F)
Resistance between terminal and sensor body: 1 M
or more
If any faulty is found, replace.
SENSOR ROTOR INSPECTION

Check rotor for being missing, damaged or deformed.

Turn drive shaft and check if rotor rotation is free from eccentricity
and looseness.

Check that no foreign material is attached.
If any faulty is found, repair or replace. Refer to WHEEL HUB RE-
MOVAL and INSTALLATION in Section 3D.

YH4
GRAND
VITARA
7A
MANUAL TRANSMISSION (TYPE 1) 7A-1
TYPE 1
GENERAL DESCRIPTION7A- 1 . . . . . . . . . . . . . .
DIAGNOSIS7A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A- 3 . . . . . . . . . . . . . . . .
Gear Oil 7A- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A- 4. . . . . . . . . . . . . . . . . . .
Switches 7A- 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A- 8. . . . . . . . . . . . . . . .
Dismounting of Trans. Unit 7A- 9. . . . . . . . . . . . .
Remounting of Trans. Unit 7A-12. . . . . . . . . . . . . Extension Case (2WD MODEL) 7A-13. . . . . . . .
Extension Case Oil Seal
(2WD MODEL) 7A-13. . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A-14 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A-14 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A-14 . . . . . .
SPECIAL TOOL7A-14 . . . . . . . . . . . . . . . . . . . . . . .
As the aluminum case is sealed with liquid type gas-
ket, it is necessary to use genuine sealant or its equiv-
alent on its mating surfaces when reassembling it.
Also, the case fastening bolts must be tightened to
specified torque by means of the torque wrench and
tightening over or below the specified torque should
be avoided.
The description under ON-VEHICLE SERVICE in this
section covers a part of the TYPE 2 manual transmis-
sion and the transfer. The transfer is next to the trans-
mission as well, but their gear boxes are independent
and each of them has its own drain and level / filler
plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A
MANUAL TRANSMISSION
(TYPE 1)
CONTENTS
GENERAL DESCRIPTION
The manual transmission consists of the input shaft,
main shaft, countershaft and reverse gear which are
installed in the aluminum case. Its gears are of for-
ward five speeds in synchro mesh and reverse one
speed in constant mesh system.
The main shaft gears are held by the needle bearings
and on them the synchronizer rings and synchronizer
sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.

YH4
GRAND
VITARA
Viscosity chart
SAE
1. Reverse idle gear shaft bolt
(DO NOT LOOSEN IT)
MANUAL TRANSMISSION (TYPE 1) 7A-3
ON-VEHICLE SERVICE
GEAR OIL
INSPECTION AND CHANGE
1) Before changing or inspecting oil, be sure to stop engine and lift
vehicle horizontally.
2) With vehicle lifted up, check oil level and leakage. If leakage ex-
ists, correct or repair it.
3) Drain old oil and fill new specified oil as shown below by speci-
fied amount (roughly up to level hole).
NOTE:

It is highly recommended to use SAE 75W-90 gear oil.

Whenever vehicle is hoisted for any other service work
than oil change, also be sure to check for oil leakage and
status of breather hoses.

If water or rust is mixed in drained oil, be sure to check
breather hose and boot of transmission and transfer.
Gear Oil Specification
Oil grade: API GL-4
Viscosity: SAE 75W-85, 75W-90 or 80W-90
Oil Capacity:
Transmission 1.5 liters (3.2 / 2.6 US / Imp. pt)
Transfer 1.7 liters (3.6 / 3.0 US / Imp. pt)
4) Torque drain plug and level / filler plug as specified below after
applying sealant to its thread.
CAUTION:

Transmission oil must not be poured through gear shift
control lever part.

Do not loosen or remove reverse idle gear shaft bolt.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
7A-14 MANUAL TRANSMISSION (TYPE 1)
09951-16060
Oil seal installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Control lever boot cover bolts60.64.0
4WD switch202.014.5
Back up light switch (Type 1)202.014.5
Back up light switch (Type 2)454.532.5
Control lever locating bolts171.712.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts and nut505.036.5
Exhaust center pipe to manifold nuts505.036.5
Muffler to exhaust center pipe bolts505.036.5
Universal joint flange bolts505.036.5
Select return spring bolts232.317.0
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)
Shift control lever.

Select return springs, bolts and guides.
Thread lock cementTHREAD LOCK CEMENT
SUPER 1333B (99000-32020)
Shift control lever locating bolts.
SealantSUZUKI BOND No. 1215
(99000-31110)
Oil Drain and filler / level plugs.
SPECIAL TOOL

YH4
GRAND
VITARA
7A1
MANUAL TRANSMISSION (TYPE 2) 7A1-1
TYPE 2
GENERAL DESCRIPTION7A1-1 . . . . . . . . . . . . . .
DIAGNOSIS7A1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A1-3 . . . . . . . . . . . . . . . .
Gear Oil 7A1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A1-4. . . . . . . . . . . . . . . . . . .
Switches 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A1-4. . . . . . . . . . . . . . . . Dismounting / Remounting of
Trans. Unit 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A1-4 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A1-5 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A1-5 . . . . . .
The manual transmission consists of the input shaft,
main shaft, counter shaft and reverse gear which are
installed in the aluminum and castings cases. Its
gears are of forward five speeds in synchro mesh and
reverse one speed in sliding idler gear arrangement
system.
The main shaft gears are held by the needle bear-
ings and on them the synchronizer rings and syn-
chronizer sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.As the aluminum and castings cases are sealed with
liquid type gasket, it is necessary to use genuine seal-
ant or its equivalent on its mating surfaces when reas-
sembling them. Also, the case fastening bolts must be
tightened to specified torque by means of the torque
wrench and tightening over or below the specified
torque should be avoided.
The description under ON-VEHICLE SERVICE in this
section covers the transfer partially which is next to
the transmission as well, but their gear boxes are in-
dependent and each of them has its own drain and
level / filler plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A1
MANUAL TRANSMISSION
(TYPE 2)
CONTENTS
GENERAL DESCRIPTION