2005 SUZUKI GRAND VITARA diagnosis
[x] Cancel search: diagnosisPage 429 of 801
YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-27
A / T BASIC CHECK
This inspection is important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been noted in visual inspection.
Follow flow table carefully.
STEP
ACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Perform MANUAL ROAD TEST in this section.
Is it OK?Go to Step 3.Go to Step 4.
3Proceed to TROUBLE DIAGNOSIS TABLE 1 in this
section.
Is trouble identified?Repair or replace
defective parts.Go to Step 5.
4Perform stall test, time rag test, line pressure test,
engine brake test and ªPº range test referring to STALL
TEST, LINE PRESSURE TEST, ENGINE BRAKE
TEST and ªPº RANGE TEST in this section.
Are the test results satisfactory?Go to Step 5.Proceed to
TROUBLE DIAGNO-
SIS TABLE 3 in this
section.
5Proceed to TROUBLE DIAGNOSIS TABLE 2 in this
section.
Is trouble identified?Repair or replace
defective parts.Proceed to
TROUBLE DIAGNO-
SIS TABLE 3 in this
section.
Page 430 of 801
YH4
GRAND
VITARA
7B1-28 AUTOMATIC TRANSMISSION (4 A / T)
Transmission fluid Running condition Running condition Gear shift
TROUBLE DIAGNOSIS TABLE 1
ConditionPossible CauseCorrection
TCC does not operateBrake pedal (stop lamp) switch or its
circuit faulty (H25 engine only)
4WD low switch or its circuit faulty
Engine coolant temp. sensor or its
circuit faulty
Cruise control signal circuit faulty
(if equipped)DIAGNOSTIC FLOW TABLE A-1
Gear does not change
to 4thO / D cut switch or its circuit faulty
4WD low switch or its circuit faulty
Engine coolant temp. sensor or its
circuit faulty
Cruise control signal circuit faulty
(if equipped)DIAGNOSTIC FLOW TABLE A-2
TROUBLE DIAGNOSIS TABLE 2
ConditionPossible CauseCorrection
Low fluid pressureClogged oil pump strainer
Malfunction of pressure regulator valveWash strainer.
Overhaul valve body.
High fluid pressurePressure regulator valveOverhaul valve body.
Unable to run in all
rangeRegulator valve stickReplace.
Clogged oil strainerWash strainer.
Seized or broken planetary gearRepair or replace.
Faulty manual valveReplace.
Poor 1st speed run-
ning or excessive
slippage in ªDº or
ª2ºFaulty 1±2 shift valveReplace.
Poor 1±2 shift, ex-
ili
Regulator valve stickingReplace.
cessive slippage1±2 shift valve stickingReplace.
Shift solenoid valve-B stickingReplace.
Intermediate coast modulator valve stick-
ingReplace.
Poor 2±3 shift, ex-
ili
2±3 shift valve stickingReplace.
cessive slippageShift solenoid valve-A stickingReplace.
Poor start or surg-
ing in ªDº rangeRegulator valve stickingReplace.
Page 431 of 801
YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-29
Gear shift Transmission fluid Running condition
ConditionPossible CauseCorrection
Poor 3±4 shift, ex-3±4 shift valve stickingReplace.
cessive slippageShift solenoid valve-B stickingReplace.
Excessive shock onRegulator valve stickingReplace.
1±2 shiftFaulty accumulator, second brake pistonReplace.
Excessive shock onRegulator valve stickingReplace.
2±3 shiftFaulty accumulator, direct clutch pistonReplace.
Excessive shock on
3±4 shiftRegulator valve stickingReplace.
Non operate lock-TCC (Lock-up) control valve stickingReplace.
up systemSolenoid valve No.2 (TCC solenoid valve)
stickingReplace.
TROUBLE DIAGNOSIS TABLE 3
ConditionPossible CauseCorrection
Low fluid pressureLeakage from oil pressure circuitOverhaul.
Unable to run in all
rangeWear in oil pumpReplace.
Seizure in oil pumpReplace.
Fluid pressure leakage to over drive clutch
due to wear of oil pump bushingReplace.
Faulty in torque converterReplace.
Page 482 of 801
YH4
GRAND
VITARA
7C1
CLUTCH 7C1-1
GENERAL DESCRIPTION7C1 - 2 . . . . . . . . . . . . .
DIAGNOSIS7C1 - 3 . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7C1 - 4 . . . . . . . . . . . . . . .
Clutch Pedal Height 7C1 - 4. . . . . . . . . . . . . . . . . .
Clutch Pedal Free Travel 7C1 - 4. . . . . . . . . . . . .
Clutch Fluid Pipe and Hose 7C1 - 4. . . . . . . . . . .
Clutch Master Cylinder 7C1 - 5. . . . . . . . . . . . . . .
Fluid Inspection 7C1 - 6. . . . . . . . . . . . . . . . . . . . .
Disassembly and Assembly
Clutch Master Cylinder 7C1 - 7. . . . . . . . . . . . . . Clutch Operating Cylinder 7C1 - 8. . . . . . . . . . . .
UNIT REPAIR7C1-10 . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Cover, Clutch Disc and
Flywheel 7C1 - 10. . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7C1-14 . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7C1-14 . . . . .
SPECIAL TOOLS7C1-14 . . . . . . . . . . . . . . . . . . . . .
SECTION 7C1
CLUTCH
CONTENTS
Page 484 of 801
YH4
GRAND
VITARA
CLUTCH 7C1-3
DIAGNOSIS
ConditionPossible CauseCorrection
SlippingImproper clutch pedal free travel.
Worn or oily clutch disc facing.
Warped disc, pressure plate or flywheel
surface.
Weakened diaphragm spring.
Master cylinder piston or seal cup not returning.Bleed air or replace master
cylinder.
Replace disc.
Replace disc, clutch cover or
flywheel.
Replace clutch cover.
Repair master cylinder.
Dragging clutchImproper clutch pedal free travel.
Weakened diaphragm spring, or worn spring tip.
Rusted input shaft splines.
Damaged or worn splines of transmission
input shaft.
Excessively wobbly clutch disc.
Clutch facings broken or dirty with oil.
Fluid leakage.Bleed air or replace master
cylinder.
Replace clutch cover.
Lubricate.
Replace input shaft.
Replace disc.
Replace disc.
Repair or replace.
Clutch vibrationGlazed (glass-like) clutch facings.
Clutch facings dirty with oil.
Release bearing slides unsmoothly on input
shaft bearing retainer.
Wobbly clutch disc, or poor facing contact.
Weakened torsion springs in clutch disc.
Clutch disc rivets loose.
Distorted pressure plate or flywheel surface.
Weakened or loosened engine mounting
bolt or nut.Repair or replace disc.
Replace disc.
Lubricate or replace input
shaft bearing retainer.
Replace disc.
Replace disc.
Replace disc.
Replace clutch cover or flywheel.
Retighten or replace mounting.
Noisy clutchWorn or broken release bearing.
Input shaft front bearing worn down.
Excessive rattle of clutch disc hub.
Cracked clutch disc.
Pressure plate and diaphragm spring rattling.Replace release bearing.
Replace input shaft bearing.
Replace disc.
Replace disc.
Replace clutch cover.
Grabbing clutchClutch disc facings soaked with oil.
Clutch disc facings excessively worn.
Rivet heads showing out of facing.
Weakened torsion springs.Replace disc.
Replace disc.
Replace disc.
Replace disc.
Page 496 of 801
YH4
GRAND
VITARA
7D
TRANSFER 7D-1
The aluminum transfer case directly connected to the
back of the transmission contains the input gear,
countershaft & gear, output rear shaft, output low gear
and output front shaft (for front drive) connected by
way of the hyvo-chain.
The transfer has such a selective mechanism as to
enable the shift control lever to make selection of high
speed (direct connection with transmission output:
main shaft), low speed (speed reduction by input
gear, counter gear and output low gear) or neutral by
way of the reduction sleeve located between input
gear and output low gear, and selection of two-wheel-
drive (high speed only) or four-wheel-drive (high or
low speed) by way of the front drive clutch sleeve lo-cated at the center of the output rear shaft. Also, with
a synchronizer installed to the front drive clutch, it is
possible to change the drive mode between 2WD
(high speed only) and 4WD (high speed only) even
while running.
The front drive shift fork has an auxiliary spring to
make a smooth shift from 4H to 2H possible.
The case has an oil gutter and a plate at synchronizer
to provide proper lubrication even under the strict
conditions of use.
WARNING:
For towing the vehicle for the purpose of repair or
the like, follow the towing instructions in OWN-
ER'S MANUAL.
SECTION 7D
TRANSFER
CONTENTS
GENERAL DESCRIPTION7D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Oil Seals7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer Driven Gear7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Assembly7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7D-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
Page 497 of 801
YH4
GRAND
VITARA
7D-2 TRANSFER
DIAGNOSIS
DIAGNOSIS TABLE
Before attempting to repair the transfer or related components for any reason other than mechanical failure, the
condition and probable causes should be identified.
Transfer failures are revealed by shifting difficulties such as excessive shifting effort, gear clash, or gear grinding.
When any of these conditions occur, the following inspections should be made before disassembling the transfer.
1) Check transfer oil level for insufficient or incorrect oil. Refer to ªTransfer and Differential Oil Inspection and
Changeº in SECTION 0B ªMAINTENANCE AND LUBRICATIONº.
2) Check transfer mountings for wear or looseness.
3) Check gearshift control lever for distortion or excessive wear.
After performing the above inspections, refer to following diagnosis table.
Condition
Possible CauseCorrection
Gear slipping out of meshWorn shift fork shaft
Worn shift fork or synchronizer sleeve
Weak or damaged locating spring
Worn bearings on output rear shaft
Worn chamfered tooth on sleeve or gear
Missing or disengagement of circlip(s)Replace
Replace
Replace
Replace
Replace sleeve and gear
Install
Gears refusing to disengageWeakened or broken synchronizer spring
Distorted shift shaft or shift forkReplace
Replace
Hard shiftingWeakened front drive shift shaft spring
Distorted or mispositioned front drive shift
shaft circlip and washer
Inadequate or insufficient lubricant
Worn synchronizer ring
Worn chamfered tooth on sleeve or gear
Distorted shift shaftReplace
Replace
Replenish
Replace
Replace sleeve and gear
Replace
NoiseInadequate or insufficient lubricant
Damaged or worn bearing(s)
Damaged or worn gear(s)
Damaged or worn synchronizer ring
Damaged or worn chamfered tooth on
sleeve or gearReplenish
Replace
Replace
Replace
Replace
Page 503 of 801
YH4
GRAND
VITARA
7E
DIFFERENTIAL (FRONT) 7E-1
The differential assembly using a hypoid bevel pinion
and gear is installed to the front axle.
4WD control system controls drive force to be trans-
mitted to front axles or not. The reduction ratio varies
depending on transmission or engine type.The differential assembly is decisive in that the drive
power is concentrated there. Therefore, use of genu-
ine parts and specified torque is compulsory. Further,
because of sliding tooth meshing with high pressure
between bevel pinion and gear, it is mandatory to lu-
bricate them by hypoid gear oil.
SECTION 7E
DIFFERENTIAL (FRONT)
CONTENTS
GENERAL DESCRIPTION7E- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD CONTROL SYSTEM7E- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS TABLE7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Assembly7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD Control System Diagnostic Flow Table 7E- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD CONTROL CIRCUIT INSPECTION 7E- 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE SERVICE7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil Change7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION7E-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD Control System7E-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actuator7E-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Pump Assembly7E-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION 7E-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Mountings7E-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISMOUNTING7E-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOUNTING7E-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION