3-60
Instruments and controls
dicator light (green) located to the right of the button
will illuminate."
By pressing and releasing the right button, the com-
pass display is toggled on or off. When the compass is
on, an illuminated compass reading will appear in the
lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror sur-
face turns bright if the transmission is shifted into re-
verse. This is to ensure good rearward visibility during reversing. ! Photosensors
The mirror has a photosensor attached on both the
front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors
detect it and make the reflection surface of the mirror
dimmer to help prevent you from being blinded. For
this reason, use care not to cover the sensors with
stickers, or other similar items. Periodically wipe the
sensors clean using a piece of dry soft cotton cloth or
an applicator. !
Compass calibration
1. For optimum calibration, switch off all nonessential
electrical accessories (rear window defogger, heater/
air conditioning system, spotlight, etc.) and ensure all
doors are shut.
2. Drive to an open, level area away from large metal-
lic objects or structures and make certain the ignition
switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then re-
lease, and the compass will enter the calibration
mode. “CAL” and direction will be displayed.
4. Drive slowly in a circle until “CAL” disappears from
the display (about two or three circles). The compass
is now calibrated.
5. Further calibration may be necessary should out-
side influences cause the mirror to read inaccurately.
You will know that this has occurred if your compass
begins to read in only limited directions. Should you
encounter this situation, return to step one of the
above procedure and recalibrate the mirror.
HS3038BA
7-19
Starting and operating
– CONTINUED –
risen to a certain level, automatic downshift nor-
mally takes place. In the meantime, downshift
manually for engine braking as required.
Also, a 4th-to-3rd automatic downshift will not oc-
cur at speeds above 50 mph (80 km/h) and a 3rd-
to-2nd automatic downshift will not occur at
speeds above 24 mph (38 km/h). !Selector lever reverse inhibiting func- tion
This function prevents accidental movement of the se-
lector lever to the “R” position while the vehicle is mov-
ing.
The function becomes operational when the vehicle
reaches a speed of approximately 6 mph (10 km/h).
Once operational, it prevents the selector lever from
being moved from the “N” position to the “R” position.
When the vehicle speed drops below 6 mph (10 km/h),
the function is canceled. The selector lever can then
be moved to the “R” and “P” positions.
When the ignition switch has been turned to the “OFF”
position, movement of the selector lever from the “N”
position to the “R” position is possible for a limited time
period and then becomes impossible. Also, the selec-
tor lever cannot be moved to the “R” position when it
has been placed in the “P” position and then placed again in the “N” position. When movement of the se-
lector lever from the “N” position to the “R” position has
become impossible, turn the ignition switch back to the
“ON” position then move the selector lever to the “P”
position. Pressing the selector lever release button
also makes it possible to move the selector lever to the
“P” position at this time. !
Selector lever release button
If you inadvertently have turned the ignition switch to
the “OFF” position with the selector lever in the “N” po-
sition, proceed as follows. By referring to the “Shift
lock release” section in this chapter, remove the shift
lock release cover. Then, with the screwdriver inserted
UB7207BA
7-29
Starting and operating
– CONTINUED –
Once operational, it prevents the selector lever from
being moved from the “N” position to the “R” position.
When the vehicle speed drops below 6 mph (10 km/h),
the function is canceled. The selector lever can then
be moved to the “R” and “P” positions.
When the ignition switch has been turned to the “OFF”
position, movement of the selector lever from the “N”
position to the “R” position is possible for a limited time
period and then becomes impossible. Also, the selec-
tor lever cannot be moved to the “R” position when it
has been placed in the “P” position and then placed
again in the “N” position. When movement of the se-
lector lever from the “N” position to the “R” position has
become impossible, turn the ignition switch back to the
“ON” position then move the selector lever to the “P” position. Pressing the selector lever release button
also makes it possible to move the selector lever to the
“P” position at this time. !
Selector lever release button
If you inadvertently have turned the ignition switch to
the “OFF” position with the selector lever in the “N” po-
sition, proceed as follows. By referring to the “Shift
lock release” section in this chapter, remove the shift
lock release cover. Then, with the screwdriver inserted
into the hole, move the selector lever to the “P” posi-
tion. If the selector lever reverse inhibiting function
fails, have the vehicle inspected by the nearest SUB-
ARU dealer.
UB7207BA
7-31
Starting and operating
– CONTINUED –
goes off.
Gearshifts can be performed using the selector lever
or the shift switch on the steering wheel (turbo model
only).
Using the selector lever
Shift to the next-higher gear by briefly pushing the se-
lector lever toward the “+” end of the manual gate.
Shift to the next-lower gear by briefly pulling the selec-
tor lever toward the “–” end of the manual gate. Using the shift switch (turbo models)
Shift to the next-higher gear by briefly pressing the “+”
button of the shift switch.
Shift to the next-lower gear by briefly pressing the “–”
button of the shift switch.
To deselect the manual mode, return the selector le-
ver to the “D” position from the manual gate.
If you press the “+” button or “–” button of the shift
switch while driving with the selector lever in the “D”
position, the manual mode will be selected. At this
time, the currently selected gear will be shown by the
gear position indicator and the upshift indicator and
downshift indicator will come on.
UB7206BA
UB7505BA
8-14
Driving tips
ing, abrupt acceleration, high-speed driving, and
sharp turning when driving on snowy or icy roads.
Always maintain ample distance between your vehicle
and the vehicle ahead of you to avoid the need for sud-
den braking.
To supplement the foot brake, use the engine brake
effectively to control the vehicle speed. (Shift into a
lower gear when necessary.)
Avoid shifting down abruptly. Such behavior can
cause the wheels to lock, possibly leading to loss of
vehicle control.
An anti-lock brake system (ABS) enhances your vehi-
cle’s braking performance on snowy and icy roads.
Refer to the “ABS (Anti-lock Brake System)” and “Ve-
hicle Dynamics Control system (if equipped)” section
in chapter 7 for information on braking on slippery sur- faces. !
Wiper operation when snowing
Before driving in cold weather, make sure the wiper
blades are not frozen to the windshield or rear window.
If the wiper blades are frozen to the windshield or rear
window, use the defroster with the airflow control but-
ton/dial in the “ ” position and the temperature
control dial set for maximum warmth until the wiper
blades are completely thawed out. If your vehicle is
equipped with a wiper deicer, it is helpful to thaw the windshield wiper blades. To thaw out the rear wiper
blade, use the rear window defogger.
When driving in snow, if frozen snow starts to stick on
the surface of the windshield despite wiper operation,
use the defroster with the airflow control button/dial in
“ ” and the temperature control dial set for maxi-
mum warmth. After the windshield gets warmed
enough to melt the frozen snow on it, wash it away us-
ing the windshield washer.
Snow stuck on the wiper arm prevents the wiper from
working effectively. If snow is stuck on the wiper arm,
pull off the road to a safe place, then remove it. If you
stop the vehicle at road side, use the hazard warning
flasher to alert other drivers.
We recommend use of non-freezing type wiper blades
(winter blades) during the seasons you could have
snow and sub-zero temperatures. Blades of this type
give superior wiping performance in snowy conditions.
Be sure to use blades that are suitable for your vehi- cle. !
Corrosion protection
Refer to the “Corrosion protection” section (chapter
10).
14-2
Index
A
ABS (Anti-lock Brake System) ........................... 7-38
Warning light ........................................ 3-28, 7-39
Accessories ..................................................... 11-72
Accessory power outlet ..................................... 6-14
Active head restraint ............................................ 1-8
Air cleaner element ......................................... 11-24
Air conditioner ..................................................... 4-9
Air filtration system ............................................ 4-19
Air flow selection ................................................. 4-2
Alarm system ..................................................... 2-23
All-wheel drive warning light (AT vehicles) ........ 3-31
Aluminum wheels ............................................ 11-57
Antenna system .................................................. 5-2
Anti-lock Brake System (ABS) ........................... 7-38
Arming the system ............................................. 2-24
Armrest .............................................................. 1-14
Ashtray .............................................................. 6-19
AT OIL TEMPerature warning light ................... 3-27
Audio control button .......................................... 5-56
Audio set ............................................................. 5-3
Auto-dimming mirror/compass .......................... 3-59
Automatic climate control system ...................... 4-10
Automatic transmission 4 speed ......................................................... 7-16
5 speed ......................................................... 7-25
Capacities ..................................................... 12-4 Fluid ............................................................ 11-33
Manual mode ....................................... 7-20, 7-30
Selector lever ...................................... 7-17, 7-26
Shift lock release ................................. 7-24, 7-35
Temperature warning light (AT OIL TEMP) .. 3-27
Automatic/Emergency Locking Retractor (A/ELR) .......................................................... 1-18
B
Battery ............................................................. 11-67 Jump starting ................................................ 9-17
Replacement (Remote keyless entry system) ...................................................... 2-16
Brake Booster ....................................................... 11-44
Fluid ............................................................ 11-42
Pad and lining ............................................. 11-47
Pedal .......................................................... 11-45
Brake pedal
Free play .................................................... 11-45
Reserve distance ........................................ 11-45
Brake system .................................................... 7-37
Warning light ................................................ 3-29
Braking .............................................................. 7-37
Breaking-in of new brake pads and linings ....................................................... 11-47
Tips ............................................................... 7-37