2005 SUBARU OUTBACK towing

9-25
In case of emergency
– CONTINUED –
5. Screw the towing hook into the thread hole until the
threads can no longer be seen. 6. Tighten the towing hook securely by a wheel nut
wrench.
After towing, remove the towing hook from the vehicle
and stow it in the tool bag.
Fit the fog light cover and towing hook cover on the
bumper.
"
Do not use the towing hook except when tow-
ing your vehicle. " Be sure to remove the towing hook after tow-
ing. Leaving the towing hook mounted on the
vehicle could interfere with proper operation of
UB9206BAUB9207BA

9-26
In case of emergency
the SRS airbag system in a frontal collision.
Rear towing hook:
The rear towing hook is located below the center of the
rear bumper.
Never use the rear towing hook to tie the vehi-
cle down. Front tie-down hooks:
The front tie-down hooks are located between each of
the front tires and the front bumper.
UB9509BA
UB9202BA

9-28
In case of emergency
!
Towing with all wheels on the ground
"Never turn the ignition switch to the “LOCK”
position while the vehicle is being towed be-
cause the steering wheel and the direction of
the wheels will be locked." Remember that the brake booster and power
steering do not function when the engine is not
running. Because the engine is turned off, it will
take greater effort to operate the brake pedal
and steering wheel.
" If transmission failure occurs, transport your
vehicle on a flat-bed truck. " Do not run the engine while being towed us-
ing this method. Transmission damage could
result if the vehicle is towed with the engine
running. " For vehicles with automatic transmission,
the traveling speed must be limited to less than
20 mph (30 km/h) and the traveling distance to
less than 31 miles (50 km). For greater speeds
and distances, transport your vehicle on a flat-
bed truck.
1. Check the transmission and differential oil levels
and add oil to bring it to the upper level if necessary.
2. Release the parking brake and put the transmis-
sion in neutral.
3. The ignition switch should be in the “ACC” position
while the vehicle is being towed.
4. Take up slack in the towline slowly to prevent dam-
age to the vehicle.UB9219BA

9-35
In case of emergency
– CONTINUED –
Station wagon: Open the center lid, remove the left
hand part of the lid, and take out the jack handle.
For how to use the jack, refer to “Flat tires”. !
Other maintenance tools
In addition to a jack and a jack handle, the tool bucket
on your vehicle contains the following maintenance
tools.
Screwdriver
Towing hook
Wheel nut wrench
Hex-headed wrench (only for vehicles with moon- roof)
UB9504BA
UB9217BA

11 -1 7
Maintenance and service
– CONTINUED –
API Service label
A) Indicates the oil quality by API designations
B) Indicates the SAE oil viscosity grade
C) Indicates that the oil has fuel saving capabilities
In choosing an oil, you want the proper quality and vis-
cosity, as well as one that will add to fuel economy.
The following table lists the recommended viscosities
and applicable temperatures.
When adding oil, different brands may be used togeth-
er as long as they are the same API classification and
SAE viscosity as those recommended by SUBARU. SAE viscosity number and applicable temperature
*: 5W-30 is preferred.
Engine oil viscosity (thickness) affects fuel economy.
Oils of lower viscosity provide better fuel economy.
However, in hot weather, oil of higher viscosity is re-
quired to properly lubricate the engine. ! Recommended grade and viscosity
under severe driving conditions
If the vehicle is used in desert areas, in areas with very
high temperatures, or used for heavy-duty applica-
tions such as towing a trailer, use of oil with the follow-
ing grade and viscosities is recommended.
APISERVICESL
ENERGYCONSERVING
SAE
5W-30
A
B
C
HSB022BC
5W-30*10W-30, 10W-40
-30 -20 -10 0 10 20 30 40
-20
06 0
20 80 100 40
HSB024BA

12-5
Specifications
– CONTINUED –
!Tires
! Wheel alignment
Tire sizeP205/55R16 89H215/45ZR17P225/60R16 97HP225/55R17 95V
Wheel size16 x 6.5JJ17 x 7JJ16 x 6.5JJ17 x 7JJ
PressureFront32 psi
(220 kPa, 2.2 kgf/cm 2
)35 psi
(240 kPa, 2.4 kgf/cm 2
)32 psi (220 kPa, 2.2 kgf/cm 2
)
Rear30 psi
(210 kPa, 2.1 kgf/cm 2
)33 psi
(230 kPa, 2.3 kgf/cm 2
)30 psi (210 kPa, 2.1 kgf/cm 2
)
Rear at trailer
towing–32 psi (220 kPa, 2.2 kgf/cm 2
)
Temporary
spare tireSizeT135/80R16T135/70D17T155/70D17
Pressure60 psi (420 kPa, 4.2 kgf/cm 2
)
ItemLegacyOUTBACK
SedanStation wagonSedanStation wagon
ToeFront0 in (0 mm)
Rear0 in (0 mm)
CamberFront–0 °15’0 °40’
Rear–0 °40’–0 °30’–0 °10’

13-6
Consumer information and Reporting safety defects !
Recommended tire inflation pressure
! Recommended cold tire inflation pressure
Recommended cold tire inflation pressure for your vehicle’s tires is as follows,
Tire size P205/55R16 89H215/45ZR17 P225/60R16
97HP225/55R17
95V
Wheel size 16 x 6.5JJ 17 x 7JJ 16 x 6.5JJ 17 x 7JJ
Pressure Front 32 psi (220 kPa, 2.2 kgf/cm2
) 35 psi (240 kPa,
2.4 kgf/cm 2
) 32 psi (220 kPa, 2.2 kgf/cm
2
)
Rear 30 psi (210 kPa, 2.1 kgf/cm2
) 33 psi (230 kPa,
2.3 kgf/cm 2
) 30 psi (210 kPa, 2.1 kgf/cm
2
)
Rear at trailer towing – 32 psi (220 kPa, 2.2 kgf/cm
2
)
Tempo-
rary spare tire Size T135/80R16 T135/70D17 T155/70D17
Pressure 60 psi (420 kPa, 4.2 kgf/cm
2
)

13-10
Consumer information and Reporting safety defects
left hand side of the vehicle. (Each tire must be
kept on its original side of the vehicle.) Replace
any damaged or unevenly worn tire at the time of
rotation. After tire rotation, adjust the tire pres-
sures and make sure the wheel nuts are correct-
ly tightened. A tightening torque specification
and a tightening sequence specification for the
wheel nuts can be found “Flat tires” in Chapter 9. !
Vehicle load limit – how to determine
The load capacity of your vehicle is determined
by weight, not by available cargo space. The
load limit of your vehicle is shown on the vehicle
placard attached to the driver’s side B-pillar. Lo-
cate the statement “The combined weight of oc-
cupants and cargo should never exceed XXX kg
or XXX lbs” on your vehicle’s placard.
The vehicle placard also shows seating capacity
of your vehicle.
The total load capacity includes the total weight
of driver and all passengers and their belong-
ings, any cargo, any optional equipment such as
a trailer hitch, roof rack or bike carrier, etc., and
the tongue load of a trailer. Therefore cargo ca- pacity can be calculated by the following method.
Cargo capacity = Load limit – (total weight of oc-
cupants + total weight of optional equipment +
tongue load of a trailer (if applicable))
For towing capacity information and weight lim-
its, refer to “Trailer towing” in Chapter 8. !
Calculating total and load capacities vary-
ing seating configurations
Calculate the available load capacity as shown in
the following examples:
Example 1A
UBD201BA