2005 SUBARU OUTBACK ESP

3-41
Instruments and controls
– CONTINUED –
Canada-spec. vehicles
This indication shows the average rate of fuel con-
sumption since the trip meter was last reset.
Pressing the trip knob toggles the indication between
the average fuel consumption corresponding to the A
trip meter indication and the average fuel consumption
corresponding to the B trip meter indication.
When either of the trip meter indications is reset, the
corresponding average fuel consumption value is alsoreset.
NOTE " The indicated values vary in accordance with
changes in the vehicle’s running conditions. Also, the indicated values may differ slightly from the
actual values and should thus be treated only as a
guide. "
When either trip meter indication is reset, the av-
erage fuel consumption corresponding to that trip
meter indication is not shown until the vehicle has
subsequently covered a distance of 1 mile (or 1 km). ! Driving range on remaining fuel
U.S.-spec. vehicles
UB3203AA
UB3570AA

4-8
Climate control
er button will not come on. At the same time, the
air inlet selection is automatically set to “outsideair” mode.
In this state, you cannot select “recirculation”
mode by manually pressing the air inlet selectionbutton.
Also, you cannot stop the air conditioner com-
pressor by pressing the air conditioner button."
Warm air also comes out from the right and left
air outlets. To stop warm air flow from these out-
lets, turn the corresponding wheel to the “ ”
position. ! Heating and defrosting
To direct warm air toward the floor and the windshield:
1. Set the air inlet selection lever to the “OFF” posi-tion.
2. Set the air flow control dial to the “ ”position.
3. Set the temperature control dial to the most com-
fortable level.
4. Set the fan speed control dial to the desired speed.
NOTE " In a vehicle equipped with an air conditioner,
when the dial is placed in the “ ” position or
“ ” position the air conditioner compressor au-
tomatically operates to quickly defog the wind-
shield. However the indicator on the air condition- er button will not come on. At the same time, the
air inlet selection is automatically set to “outside
air” mode.
In this state, you cannot select “recirculation”
mode by manually pressing the air inlet selectionbutton.
Also, you cannot stop the air conditioner com-
pressor by pressing the air conditioner button."
Warm air also comes out from the right and left
air outlets. To stop warm air flow from these out-
lets, turn the corresponding wheel to the “ ”
position. ! Heating
To direct warm air toward the floor:
1. Set the air inlet selection button to the OFF posi-tion.
2. Set the air flow control dial to the “ ” position.
3. Set the temperature control dial to the most com-
fortable level.
4. Set the fan speed control dial to the desired speed.NOTE
Warm air also comes out from the right and left air
outlets. To stop warm air flow from these outlets,
turn the corresponding wheel to the “ ” posi- tion.

4-14
Climate control
the system to the setting that was selected before you
activated the defroster. !
Fan speed control button
The fan speed control button has the 7 positions:
AUTO position and 6 different fan speed positions.
The fan speed is shown by the display.
With the fan speed control button in the AUTO posi-
tion, the fan speed changes automatically correspond-
ing the various conditions: air temperature inside and
outside of the passenger’s compartment, intensity of
the sunlight, etc. !
A/C – Air conditioner button
If the windshield starts to fog when the climate control system is operated in the AUTO mode, push the air
conditioner button “A/C” to defog and dehumidify.
When this button is pushed, the air conditioner com-
pressor turns on and the indicator light “A/C” on the
display comes on. After eliminating the fogging from
the windshield, set the system back to the AUTO
mode by pushing the “AUTO” button.
NOTE
The air conditioner compressor does not operate
when the outside air temperature is below 32 °F
(0 °C).
UB4206BA
UB4207BA

5-25
Audio
– CONTINUED –
off. "The player is designed to be able to play music
CD-Rs and music CD-RWs, but it may not be able
to play certain ones. ! How to insert a CD(s)
" Inserting a CD
0
1. Briefly press the “LOAD” button. If the magazine in
the player has an idle position where you can insert a
disc, the disc number indicator associated with the idle
position will blink.
If no indicator blinks, it means that there is no idle po-
sition in the magazine.
2. When the “LOAD” indicator flashes, insert the disc. Once you have inserted the disc, the “LOAD” indicator
will go off. The disc will then be automatically drawn in,
and the player will begin to play the first track on the disc. "
To insert more discs in succession, repeat Steps 1
and 2. The magazine will be loaded with discs in the
ascending order of position number.
If you do not insert any disc in 15 seconds after you
have pressed the “LOAD” button, the player will begin
to play back the first track of the last disc you have in- serted." The disc indicator steadily lights up if a disc is al-
ready inserted in the corresponding position of the
magazine." While the player is in the loading mode, if you press
the “FM” or “AM” button, the player will enter the stand-
by mode. Press the “CD” button to start playback.
LOAD
UB5216BA

5-44
Audio
"
After the last song finishes, the disc will auto-
matically return to track 1 (the first song on the
disc) and will automatically play back. " The player is designed to be able to play music
CD-Rs and music CD-RWs, but it may not be able
to play certain ones. " Single CDs (i.e., 8 cm/3 inch CDs) are not sup-
ported, and if inserted, they will be immediately
ejected. ! How to insert a CD(s)
" Inserting a CD
0
1. Briefly press the “LOAD” button. If the magazine in
the player has an idle position where you can insert a disc, the disc number indicator associated with the idle
position will blink.
If no indicator blinks, it means that there is no idle po-
sition in the magazine.
2. When the “LOAD” indicator flashes, insert the disc.Once you have inserted the disc, the “LOAD” indicator
will go off. The disc will then be automatically drawn in,
and the player will begin to play back the first track of
the disc. "
To insert more discs in succession, repeat Steps 1
and 2. The magazine will be loaded with discs in the
ascending order of position number.
If you do not insert any disc in 15 seconds after you
have pressed the “LOAD” button, the player will begin
to play back the first track of the last disc you have in-
serted. " The disc indicator steadily lights up if a disc is al-
ready inserted in the corresponding position of the magazine. " While the player is in the loading mode, if you press
“FM” or “AM” button, the player will enter the standby
mode. Press the “CD” button to start playback.
LOAD
UB5216BA

5-61
Audio
– CONTINUED –
supported by the audio system. Otherwise, the audio
system may not play the MP3 files and may not display
folder titles and file titles. !Supported file systems
The audio system supports the following file systems: " ISO 9660 Level 1/Level 2
" Apple Extension to ISO 9660
" Joliet
" Romeo
NOTE
The audio system does not support the following
file systems: "Apple HFS
" UDF 1.50
" Mix CD (CD Extra)
! Compression format
" MPEG 1 audio layer 3 (MP3)
Bit rate: 32 kbps – 320 kbps
Sampling frequency: 32, 44.1, 48 kHz" MPEG 2 audio layer 3 (MP3)
Bit rate: 8 kbps – 160 kbps
Sampling frequency: 16, 22.05, 24 kHz !
Numbers of folders and files
" Maximum number of folders: 255 (including root
folder)" Maximum number of files: 999 (maximum number in
one folder: 255) " Maximum number of layers: 8
NOTE "Not all of the discs stored in MP3 files may be
able to be played back. " Even if a folder contains no MP3 files, it is count-
ed as a folder. " Writing software can rearrange folders and files
such that the playback order is different from the
desired one." The playback order for a given disc can be dif-
ferent with different players. ! Copyright issues
Except with respect to copies made for personal use,
duplication, distribution, and transmission of music
and other copyrighted material on a disc without per-
mission from the copyright holder is illegal.

6-15
Interior equipment
– CONTINUED –
accessory power outlet. "Do not place any foreign objects, especially
metal ones such as coins or aluminum foil, into
the accessory power outlet. That could cause a
short circuit. Always put the cap on the acces-
sory power outlet when it is not in use. " Use only electrical appliances which are de-
signed for 12V DC and which consume less
than 120W. Overloading the accessory power
outlet can cause a short circuit. Do not use dou-
ble adapters or more than one electrical appli-
ance. " If the plug on your electric appliance is either
too loose or too tight for the accessory power
outlet, this can result in a poor contact or cause
the plug to get stuck. Only use plugs that fit
properly." Use of an electric appliance in the accessory
power outlet for a long period of time while the
engine is not running can cause battery dis-
charge. " Before driving your vehicle, make sure that
the plug and the cord on your electrical appli- ance will not interfere with your shifting gears
and operating the accelerator and brake pedals.
If they do, do not use the electrical appliancewhile driving.
NOTE
When the lid of the center console is closed, a gap
remains between the center console and the lid to
allow the power outlet in the center console to be
used. Pass the electrical appliance’s cord through
this gap.
UB6216BA

6-16
Interior equipment
Cigarette lighter socket
A cigarette lighter socket can be found behind the ash-
tray lid under the climate controls. Push gently on the
lid to open it. A cigarette lighter plug is an optional ac-
cessory. It is available from your SUBARU dealer.
The cigarette lighter socket may also be used as a
power source for an in-car use electrical appliance.
"
The electrical power socket located on the
lower part of the instrument panel is originally
designed to use a genuine SUBARU cigarette lighter plug. Do not use non-genuine cigarette
lighter plugs in the socket. Doing so may cause
a short-circuit and overheating, resulting in a fire. "
If the socket is ever used for a plug-in acces-
sory such as a mobile phone, that may damage
the portion of the socket’s internal mechanism
that causes a cigarette lighter plug to “pop out”
after its lighter element is heated. Therefore, do
not place a cigarette lighter plug in a socket
that has been used, even once, to power a plug-
in accessory. Doing so may cause the plug to
stick and overheat, creating a potential fire haz-
ard." Do not place any foreign objects, especially
metal ones such as coins or aluminum foil, into
the socket. That could cause a short circuit.
UB6218BA