2005 SUBARU FORESTER headlights

3-1
3
Instruments and controls
Ignition switch .............................................. 3-3 LOCK .................................................................. 3-3
ACC .................................................................... 3-4
ON ....................................................................... 3-4
START ................................................................ 3-4
Key reminder chime .......................................... 3-5
Ignition switch light (if equipped) .................... 3-5
Key interlock release (AT vehicles only) ........ 3-6
Hazard warning flasher ................................ 3-7
Meters and gauges ....................................... 3-7 Speedometer ..................................................... 3-7
Odometer/Trip meter ........................................ 3-7
Tachometer ........................................................ 3-8
Fuel gauge ......................................................... 3-9
Temperature gauge ........................................... 3-10
Outside temperature indicator ......................... 3-11
Warning and indicator lights ....................... 3-12 Seatbelt warning light and chime .................... 3-13
SRS airbag system warning light .................... 3-13
CHECK ENGINE warning light/Malfunction indicator lamp ................................................. 3-13
Charge warning light ........................................ 3-14
Oil pressure warning light ................................ 3-15
AT OIL TEMPerature warning light
(AT vehicles) ................................................... 3-15
ABS warning light ............................................. 3-15
Vehicle Dynamics Control warning light (if equipped)/Vehicle Dynamics Control
OFF indicator light (if equipped) ................... 3-16
Brake system warning light ............................. 3-18
Door open warning lights ................................. 3-19 Low fuel warning light ...................................... 3-19
All-Wheel Drive warning light (AT vehicles) ... 3-19
Vehicle Dynamics Control operation
indicator light (if equipped) ........................... 3-20
Shift position indicator (AT vehicles) ............. 3-20
Turn signal indicator lights .............................. 3-21
High beam indicator light ................................. 3-21
Cruise control indicator light (if equipped) .... 3-21
Cruise control set indicator light (if equipped) .................................................... 3-21
Clock .............................................................. 3-22
Light control switch ...................................... 3-23 Headlights ......................................................... 3-23
High/low beam change (dimmer) .................... 3-24
Headlight flasher ............................................... 3-24
Daytime running light system ......................... 3-25
Turn signal lever ........................................... 3-25
Illumination brightness control ................... 3-26
Parking light switch ...................................... 3-27
Fog light button (if equipped) ...................... 3-27
Wiper and washer ......................................... 3-28 Windshield wiper and washer switches ......... 3-29
Rear window wiper and washer switch .......... 3-31
Windshield wiper deicer (if equipped) ........ 3-32
Rear window defogger button ..................... 3-33
Mirrors ............................................................ 3-35 Inside mirror ...................................................... 3-35
Outside mirrors ................................................. 3-37
Tilt steering wheel ......................................... 3-39

3-21
Instruments and controls
– CONTINUED –
„Turn signal indicator lights
These lights show the operation of the turn signal or
lane change signal.
If the indicator lights do not blink or blink rapidly, the
turn signal bulb may be burned out. Replace the bulb
as soon as possible. Refer to the “Replacing bulbs”
section in chapter 11. „ High beam indicator light
This light shows that the headlights are in the high
beam mode.
This indicator light also comes on when the headlight
flasher is operated. „ Cruise control indicator light (if
equipped)
The cruise control indicator light comes on when the
ignition switch is turned to the “ON” position and goes
out after about three seconds.
This light comes on when the “CRUISE” main switch
is pressed.
NOTE y If you move the cruise control lever while turn-
ing the ignition switch “ON”, the cruise control
function is deactivated and the cruise control indi- cator light flashes. To reactivate the cruise control
function, turn the ignition switch back to the
“ACC” or “LOCK” position, and then turn it again
to the “ON” position. y
If this indicator light and the “ ” indicator
light flash simultaneously during driving, have the
vehicle checked by your nearest SUBARU dealer. „ Cruise control set indicator light (if
equipped)
The cruise control set indicator light comes on when
the ignition switch is turned to the “ON” position and
goes out after about three seconds.
This light comes on when vehicle speed has been set.

3-23
Instruments and controls
– CONTINUED –
Light control switch
The light switch operates only when the ignition switch
is in the “ON” position.
To prevent battery discharge resulting from ac-
cidentally leaving your lights on when your ve-
hicle is parked, the light switch operates only
when the ignition switch is in the “ON” posi-
tion. In any other position, the vehicle’s lights
will be out.
If you park your vehicle on a roadside at night,
use the hazard warning flasher to alert the other
drivers. „
Headlights
To turn on the headlights, turn the knob on the end of
the turn signal lever. first position:
Parking lights, instrument panel illumination, tail lights
and license plate light are on.
second position:
Headlights, parking lights, instrument panel illumina-
tion, tail lights, and license plate light are on.
HS3026BA

3-24
Instruments and controls
„
High/low beam change (dimmer)
To change from low beam to high beam, push the turn
signal lever forward. When the headlights are on high
beam, the high beam indicator light “ ” on the in-
strument panel is also on.
To switch back to low beam, pull the lever back to the
detent position. „
Headlight flasher
To flash the headlights, pull the lever toward you and
then release it. The high beam will stay on for as long
as you hold the lever. The headlight flasher works
even though the lighting switch is in the “OFF” posi-tion.
When the headlights are on high beam, the high beam
indicator light “ ” on the instrument panel also
comes on.
Do not hold the lever in the flashing position for
US3059BAHS3026DA

3-25
Instruments and controls
– CONTINUED –
more than just a few seconds.
„ Daytime running light system
The tail lights, parking lights, and side marker
lights are not turned on by the daytime running
light system. The light switch must always be
turned to the “ ” position when it is dark
outside.
The low beam headlights will automatically come on at
reduced brightness when the engine has started, un-
der the following conditions: y The parking brake is fully released.
y The light switch is in the “OFF” or “ ” position.
y The automatic transmission selector lever is set at
other than the “P” position.
Turn signal lever
A) Right turn
B) Left turn
C) Lane change for right
D) Lane change for left
To activate the right turn signal, push the turn signal le-
ver up. To activate the left turn signal, push the turn
signal lever down. When the turn is finished, the lever
will return automatically. If the lever does not return af-
ter cornering, return the lever to the neutral position by
hand.
To signal a lane change, push the turn signal lever up
A B C
D
HS3027BD

3-27
Instruments and controls
– CONTINUED –
Parking light switch
The parking light switch operates regardless of the ig-
nition switch position.
By pushing the front end of this switch, following lights
will come on.
– Parking lights
– Tail lights
– License plate lights
To turn off, push the rear end of the parking light switch.
Avoid leaving these lights on for a long time because
that will run down the battery.Fog light button (if equipped)
The fog lights operate only when the headlights are on
low beam. Push the fog light button to turn the fog
lights on.
Press the button again to turn them off.
The indicator light located on the button will illuminate
when the fog lights are on.
P
UG3043BAHS3030AA

3-35
Instruments and controls
– CONTINUED –
Mirrors
Always check that the inside and outside mirrors are
properly adjusted before you start driving. „Inside mirror
A) Tab
The inside mirror has a day and night position. Pull the
tab at the bottom of the mirror toward you for the night
position. Push it away for the day position. The night
position reduces glare from headlights. T
Auto-dimming mirror/compass (if equipped)
A) Left button
B) Auto dimming indicator
C) Photosensor
D) Right button
The inside electronic compass mirror has an anti-glare
feature which automatically reduces glare coming
from headlights of vehicles behind you. It also con-
tains a built-in compass. y By pressing and releasing the left button, the auto-
matic dimming function is toggled on or off. When the
automatic dimming function is on, the auto dimming in-
dicator light (green) located to the right of the button
AHS3036BC
A
BC D
HS3037BC

3-36
Instruments and controls
will illuminate. y
By pressing and releasing the right button, the com-
pass display is toggled on or off. When the compass is
on, an illuminated compass reading will appear in the
lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror sur-
face turns bright if the transmission is shifted into re-
verse. This is to ensure good rearward visibility duringreversing. V Photosensors
The mirror has a photosensor attached on both the
front and back sides. If the glare from the headlights of
vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror
dimmer to help prevent you from being blinded. For
this reason, use care not to cover the sensors with
stickers, or other similar items. Periodically wipe the
sensors clean using a piece of dry soft cotton cloth or
an applicator. V
Compass calibration
1. For optimum calibration, switch off all nonessential
electrical accessories (rear window defogger, heater/
air conditioning system, spotlight, etc.) and ensure all
doors are shut.
2. Drive to an open, level area away from large metal-
lic objects or structures and make certain the ignition
switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then re-
lease, and the compass will enter the calibration
mode. “CAL” and direction will be displayed.
4. Drive slowly in a circle until “CAL” disappears from
the display (about two or three circles).
5. The compass is now calibrated. Further calibration
is not required. The compass will automatically cali-
brate from this point forward.
HS3038BA