2005 SUBARU BAJA turn signal

19
–
CONTINUED –
„Light control and wiper control levers/switches
1
2
3
4
5
7 6
8
9
10
11
UBF023DB
1) Parking light switch (page 3-22)
2) Windshield wiper (page 3-23)
3) Mist (page 3-25)
4) Windshield washer (page 3-25)
5) Wiper control lever (page 3-25)
6) Illumination brightness control
(page 3-21)
7) Light control lever (page 3-18)
8) Headlight ON/OFF (page 3-18)
9) Headlight flasher High/Low beam change (page 3-18)
10) Turn signal (for lane change) (page 3-20)
11) Turn signal (page 3-20)

22
TWarning and indicator light
Mark Name Page
Seatbelt warning light 3-9
SRS airbag system warning light 3-10
CHECK ENGINE warning
light/Malfunction indicator lamp 3-10
Charge warning light 3-11
Oil pressure warning light 3-12
AT OIL temperature warning light (if equipped) 3-12
or ABS warning light 3-12
or Brake system warning light 3-13
Door ajar warning light 3-14
Low fuel warning light 3-14
All-Wheel Drive warning
light (if equipped) 3-14
Switchback door indicator 3-14 Security system indicator
light (if equipped) 3-15
Cargo lamp indicator 3-16
Turn signal indicator lights 3-16
High beam indicator light 3-16
Cruise control set indicator light 7-38
Mark Name Page

2-8
Keys and doors
A: “LOCK/ARM” button (Orange)
Press to lock all doors.
Press and Hold to activate panic alarm.
Press three times in a five second period to use vehi-
cle finder function.
B: “UNLOCK/DISARM” button (Blue) 1) Press once to Unlock driver’s door.
2) Press a second time to Unlock all other doors.
C: LED
„ Locking the doors
Briefly press the “LOCK/ARM” button (for less than
two seconds) to lock all doors. An electronic chirp will
sound once and the turn signal lights will flash once. If any of the doors is not fully closed, an electronic
chirp will sound five times and the turn signal lights will
flash five times to alert you that the doors are not prop-
erly closed. When you close the door, it will automati-
cally lock.
NOTE
If the “LOCK/ALARM” button is pressed for two
seconds or longer, the panic alarm will sound.
When locking the doors in normal circumstances,
press the “LOCK/ALARM” button for less than two
seconds. For details on the panic alarm, refer to
“Sounding a panic alarm”. „
Unlocking the doors
Briefly press the “UNLOCK/DISARM” button (for less
than two seconds) to unlock the driver’s door. An elec-
tronic chirp will sound twice and the turn signal lights
will flash twice. To unlock all doors, briefly press the
“UNLOCK/DISARM” button a second time within 5
seconds.
NOTE
If the interval between the first and second press-
es of the “UNLOCK/DISARM” button (for unlock-
ing of all of the doors) is extremely short, the sys-
tem may not respond.
C
A B1
B2
HS2016BB

2-9
Keys and doors
– CONTINUED –
„Illuminated entry
The interior (dome) light will illuminate when the “UN-
LOCK/DISARM” button is pressed. These lights stay
illuminated for approximately 30 seconds if any of the
doors is not opened.
If the “LOCK/ARM” button is pressed before 30 sec-
onds have elapsed, these lights will go out. Also, these
lights will go out if the key is inserted in the ignition
switch. The interior light switch must be set to the mid-
dle position in order for this function to operate.
„ Vehicle finder function
Use this function to find your vehicle parked among
many vehicles in a large parking lot. Provided you are
within 30 feet (10 meters) of the vehicle, pressing the
“LOCK/ARM” button three times in a five-second peri-
od will cause your vehicle’s horn to sound once and its
turn signal lights to flash three times. „ Sounding a panic alarm
To activate the alarm, keep the “LOCK/ARM” button
pressed for more than two seconds .
The horn will sound and the turn signal lights will flash.
To deactivate it, press the “LOCK/ARM” button or
“UNLOCK/DISARM” button. Unless a button on the re-
mote is pressed, the alarm will be deactivated after ap- proximately 30 seconds.
„ Selecting audible signal operation
Using an electronic chirp, the system will give you an
audible signal when the doors lock and unlock. If de-
sired, you may turn the audible signal off.
To turn the audible signal off, unlock the doors by
pushing “UNLOCK/DISARM” button and then simulta-
neously depress “LOCK/ARM” and “UNLOCK/DIS-
ARM” buttons for more than two seconds. An electron-
ic chirp will sound twice and the turn signal lights will
flash twice to inform you that the audible signal has
been turned off.
To turn the audible signal on, unlock the doors by
pushing “UNLOCK/DISARM” button and then simulta-
neously depress “LOCK/ARM” and “UNLOCK/DIS-
ARM” buttons for more than two seconds. An electron-
ic chirp will sound once and the turn signal lights will
flash once to inform you that the audible signal has
been turned on.

2-15
Keys and doors
– CONTINUED –
Security system (if equipped)
The security system helps to protect your vehicle and
valuables from theft. The horn sounds and the turn
signal lights flash if someone attempts to break into
your vehicle. The starter motor is also interrupted to
prevent starting the vehicle without a key.
The system can be armed and disarmed with the re-
mote transmitter.
The system does not operate when the key is inserted
into the ignition switch. „System operation
The security system will give the following alarm indi-
cations when triggered: y The turn signal lights will flash and the horn will
sound intermittently. In addition, the starter motor will
not operate. y The alarm automatically resets after 30 seconds;
however, the alarm will reactivate if the vehicle is tam-
pered with again. The alarm will continue for six times
if any sensor continues to be activated.
The alarm is triggered by: y Opening a door.
y Application of physical shock to the vehicle (e.g. breaking glass or forced entry). Note that there are two
alarm levels for shock: warning and alarm. In warning
mode, the alarm detects lower level vibrations and
triggers 2 warning chirps on the horn and two flashes
on the lights as a deterrent to would be vandals. In
alarm mode, higher levels of shock are detected and
the system will go into full alarm. y
Ignition switch being turned on while in armed state.
NOTE yThe alarm will not be triggered by opening the
switchback door. y The alarm may not be triggered when the win-
dow is broken with a sharp-edged tool. y With the valet mode selected, the security sys-
tem does not operate and the turn signal lights do
not flash when the remote transmitter is used for
locking and unlocking.
The security system indicator light in the combi-
nation meter flashes twice per second to show
that the valet mode is selected.
For details, refer to “Valet mode” in this section. „ Arming the system
T To arm the system using remote transmitter
1. Close all windows and moonroof.

2-16
Keys and doors
2. Remove the key from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Make sure that the engine hood and switchback
door are locked.
5. Close all doors.
1) Press to Arm the system.
2) Press to Disarm the system. 1) Security system indicator light
6. Briefly press the “LOCK/ARM” button (for less than
two seconds). All doors will lock, an electronic chirp
will sound once, the turn signal lights will flash once
and the indicator light starts flashing slowly (approxi-
mately once every two seconds).
If any of the doors (except the switchback door) is not
fully closed, an electronic chirp sounds five times, the
turn signal lights flash five times to alert you that the
doors are not properly closed. When you close the
door, the system will automatically arm and doors will
automatically lock.
1 2
HS2016EB
1
UB2033BB

2-17
Keys and doors
– CONTINUED –
TTo arm the system using power door locking
switches
1. Close all windows and moonroof.
2. Remove the key from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Make sure that the engine hood and switchback
door are locked.
5. Close the doors but leave only the driver’s door or
the front passenger’s door open.
6. Push the power door locking switch forward
(“LOCK” side) to set the door locks.
7. Close the door. An electronic chirp will sound once,
the turn signal lights will flash once and the indicator
light will start flashing slowly (approximately once ev- ery two seconds) to inform you that the system hasarmed.
NOTE
The system can be armed even if the engine hood,
the windows, the switchback door and/or moon-
roof are open. Always make sure that they are fully
closed before arming the system. „
Disarming the system
Briefly press the “UNLOCK/DISARM” button (for less
than two seconds) on the remote transmitter. The driv-
er’s door will unlock, an electronic chirp will sound
twice, the turn signal lights will flash twice and the in-
dicator light will go off.
To unlock all other doors, briefly press the “UNLOCK/
DISARM” button a second time. T Emergency disarming
If you cannot disarm the system using the transmitter
(i.e. the transmitter is lost, broken or the transmitter
battery is too weak), you can disarm the system with-
out using the transmitter. To disarm the system:
1. Unlock the door with the key and then open the
door.
6
7
UB2024CC

2-18
Keys and doors
2. The alarm will sound.
3. Insert the key into the ignition switch and cycle it
from “LOCK” to “ON” three (3) times
within 5 sec-
onds .
„ Sounding a panic alarm
To activate the alarm, keep the “LOCK/ARM” button
pressed for more than two seconds .
The horn will sound and the turn signal lights will flash.
To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button.
Unless a button on the remote is pressed, the alarm
will be deactivated after approximately 30 seconds. „ Valet mode
When you choose the valet mode, the security system
does not operate. In valet mode, the remote transmit-
ter is used only for locking and unlocking the doors
and panic activation.
To enter the valet mode, open the driver’s door and
keep the “UNLOCK/DISARM” button depressed for
more than two seconds . The security system indica-
tor light will continue to flash 2 times per second indi-
cating that the system is in the valet mode.
To exit valet mode, open the driver’s door and keep the “UNLOCK/DISARM” button pressed
for more
than two seconds . The indicator will stop flashing.
„ Passive arming
When passive arming mode has been programmed by
the dealer, arming of the system is automatically ac-
complished without using the remote transmitter. Note
that in this mode, DOORS MUST BE MANUALLYLOCKED. T To enter the passive mode
Since programming the passive arming mode is a
complicated procedure, have it done by your nearestSUBARU dealer. T Arming the system
In passive mode, the system will automatically activate the alarm but WILL NOT automatically
lock the doors. In order to lock the doors you
must either lock them as indicated in step 4 be-
low or with the key once they have been closed.
Failure to lock the doors manually will result in
a higher security risk.