2005 SSANGYONG RODIUS fuse

0-11
POWER DISTRIBUTION
RODIUS 2005.07
8410-04
8410-04
I.P FUSE BOX
(1) F1 ~ F5
(2) F6 ~ F12

0-10
RODIUS 2005.07
4892-01
ABS SYSTEM
3. ON-VEHICLE SERVICE
(1) Electronic system service precautions
Take care to avoid electronic brake control module (HECU) circuit overloading. In testing for
opens or shorts, do not ground or apply voltage to any circuit unless instructed to do so by the
diagnostic procedure. Test circuits only with a high-impedance multi-meter. Never remove o
r
apply power to any control module with the ignition switch in the ON position. Always turn the
ignition to the OFF position before removing or connecting battery cables, fuses or connectors.
(2) General service precautions
Disconnect the HECU connector before performing any vehicle welding work using an electric
arc welder. Do not attempt to disassemble any component designated as nonserviceable. The
hydraulic modulator and the HECU can be seperated. (There is however no access to repai
r
the each components.)
(3) Bleeding system
Replacement modulators are shipped already filled and bled. In normal procedures requiring
removal of the modulator, such as to replace the HECU, air will not enter the modulator, and
normal bleeding will be all that is needed.
If air enters the hydraulic modulator, or if an unfilled modulator is installed, use the brake
bleeding program in the scan tool to bleed the modulator. Manual bleeding of the hydraulic
modulator is not possible.
1) Service Precautions
Brake Fluid may irritate eyes and skin. In case of contact, take the following actions:
Eye contact - rinse thoroughly with water.
Skin contact - wash with soap and water.
Ingestion - consult a physician immediately. -
-
-
To help avoid personal injury due to poor braking. DO NOT Tap into the vehicle’s
brake system to operate a trailer brake system.
When fasteners are removed, always reinstall them at the same location from which they
were removed. If a fastener needs to be replaced, use the correct part number fastener
for is not available, a fastener of equal size and strength (or stronger) may be used.
Fasteners that are not reused, and those requiring thread-locking compound will be
called out. The correct torque values must be used when installing fasteners that require
them. If the above procedures are not followed, parts or system damage could result.

0-13
ABS SYSTEM
RODIUS 2005.07
4892-01
1) System Fuse
2) Indicators
The ABS/TCS system fuse and SB2 is
located at the fuse box in engine
compartment.
The ABS and TCS indicators are in
instrument cluster.

01-3
FUSE AND RELAY
RODIUS 2005.07
8410-05
8410-05FUSES AND RELAYS
1. ENGINE COMPARTMENT FUSE AND RELAY
BOX
Fuse and relay box is located in the engine compartment, and the interior fuse box is located
under the driver side instrument panel. Especially, ICM box, an integrated circuit of relays, is
mounted along with STICS behind the driver side instrument panel.
Connector arrangement
Back of the fuse and relay box
(after removal)
Fuses and relays

01-4
RODIUS 2005.07
8410-05
FUSE AND RELAY
1) Arrangement of Fuses and Relays
2) Descriptions of Fuses and Relays

01-5
FUSE AND RELAY
RODIUS 2005.07
8410-05
2. INTERIOR FUSE COMPARTMENT
The interior fuse box is located in the lower area of driver side instrument panel.
To check the fuses, open the driver side door and remove the fuse box cover. ·
·

01-6
RODIUS 2005.07
8410-05
FUSE AND RELAY
3. ICM(INTEGRATED CONTROL MODULE) BOX
COMPARTMENT
The ICM box is installed along with RK STICS on the bracket behind the Instrument panel
undercover.
It contains an integrated module with around 14 relays according to the vehicle model. Relays
in the module are installed on the integrated circuit with a safety circuit. This system operates
with small current (by using transistor) and minimizes the sparks that occur during operations
(connection/disconnection) of relays; therefore its durability and wear resistance has been
greatly increased compared to the conventional relays.
Relays in the ICM box cannot be replaced respectively; so when the internal components
(including relay) are defective, ICM box should be replaced as an assembly.
RK STICS
ICM box

01-7
FUSE AND RELAY
RODIUS 2005.07
8410-05
1) Printed Circuit Board Arrangement of ICM Box
The figure shows the internal arrangement of ICM box when the cover is removed and then
disassembled.
The relays cannot be disassembled and replaced respectively; so the ICM box should be
replaced as an assembly when any internal components are defective.
(1) Front view