2005 SATURN VUE clock

{CAUTION:
If you spill fuel and then something ignites it,
you could be badly burned. Fuel can spray out
on you if you open the fuel cap too quickly.
This spray can happen if your tank is nearly
full, and is more likely in hot weather. Open
the fuel cap slowly and wait for any hiss noise
to stop. Then unscrew the cap all the way.
Be careful not to spill fuel. Do not top off or overll the
tank and wait a few seconds after you have nished
pumping before removing the nozzle. Clean fuel
from painted surfaces as soon as possible. See
Washing Your Vehicle on page 5-87.
When replacing the fuel cap, turn it clockwise until it
clicks. Make sure the cap is fully installed. The
diagnostic system can determine if the fuel cap has
been left off or improperly installed. This would allow fuel
to evaporate into the atmosphere. SeeMalfunction
Indicator Lamp on page 3-32.
{CAUTION:
If a re starts while you are refueling, do not
remove the nozzle. Shut off the ow of fuel by
shutting off the pump or by notifying the
station attendant. Leave the area immediately.
Notice:If you need a new fuel cap, be sure to get
the right type. Your dealer can get one for you.
If you get the wrong type, it may not t properly.
This may cause your malfunction indicator lamp to
light and may damage your fuel tank and emissions
system. SeeMalfunction Indicator Lamp on
page 3-32.
5-9
ProCarManuals.com

Notice:In cold weather, water can freeze and crack
the engine, radiator, heater core and other parts.
Use the recommended coolant and the proper
coolant mixture.
{CAUTION:
You can be burned if you spill coolant on hot
engine parts. Coolant contains ethylene glycol
and it will burn if the engine parts are hot
enough. Do not spill coolant on a hot engine.1. You can remove the coolant surge tank pressure cap
when the cooling system, including the coolant surge
tank pressure cap and upper radiator hose, is no
longer hot. Turn the pressure cap slowly
counterclockwise (left) about one-quarter of a turn.
If you hear a hiss, wait for that to stop. This will
allow any pressure still left to be vented out
the discharge hose.
2. Then keep turning the pressure cap slowly, and
remove it.
3. Fill the coolant surge tank with the proper
DEX-COOL
®coolant mixture, to the COLD line.
5-33
ProCarManuals.com

Headlamps and Sidemarker Lamps
To replace a headlamp or sidemarker bulb, do the
following:
1. Open the hood. SeeHood Release on page 5-11
for more information.
2. Remove the sidemarker fasteners.
3. Remove the sidemarker lamp from the body of the
vehicle.4. Rotate the sidemarker bulb socket counterclockwise
and remove it from the housing.
5. Replace with a new bulb.
If you need to change a headlamp bulb, continue to
follow these directions. If not, reinstall the lamp
assembly by reversing the Steps 1 through 3.
6. Remove the sidemarker housing to access the
headlamp assembly.
5-48
ProCarManuals.com

9. Push the locking tab toward the rear of the vehicle
with the tool to lift the headlamp bracket lower arm.
10. Lift up the assembly.
11. Disconnect the electrical connector from the bulb
assembly.
12. Rotate the bulb assembly counterclockwise to
remove it from the housing.
13. Replace the old bulb with a new one.
14. Reverse the steps to reinstall the headlamp and
sidemarker assembly.
Front Turn Signal and Parking
Lamps
To replace a front turn signal or parking lamp bulb, do
the following:
1. Follow Steps 1 through 9 underHeadlamps and
Sidemarker Lamps on page 5-48to access the
front turn signal or parking lamp.
2. Rotate the bulb to be replaced counterclockwise to
remove it from the headlamp housing.
3. Pull the bulb out of the bulb socket assembly.
5-50
ProCarManuals.com

4. Push the new bulb into the bulb socket assembly.
5. Insert the bulb assembly into the headlamp housing.
6. Rotate the bulb assembly clockwise until seated.
7. Reverse the steps to reinstall the lamp assemblies.
Fog Lamps
To replace a fog lamp bulb, do the following:
1. Reach through opening in lower front fascia to gain
access to the fog lamp bulb electrical connector.
2. Disconnect bulb electrical connector by lifting the
locking tab and pull it rearward to remove the
connector.
3. Rotate the bulb socket counterclockwise to
remove it.
4. Remove the bulb and replace it with the
appropriate bulb.
5-51
ProCarManuals.com

3. Disconnect the taillamp housing electrical connector
and remove the taillamp housing.
4. Turn the bulb socket being replaced
counterclockwise to disconnect it from the taillamp
housing.
5. Pull the bulb out of the bulb socket.
6. Push the new bulb into the bulb socket.
7. Reverse Steps 1 through 3 to reinstall the taillamp
assembly.Replacement Bulbs
Exterior Lamp Bulb Number
Back-up Lamps 315609442003
CHMSL W5W12092811
Fog Lamps 880C12450143
Front Sidemarker Lamps 16809425542
Front Turn Signal/Parking Lamps 3457A1999370
Headlamps
High-Beam9005
H6309441732
Low-Beam9006
HB409441733
Rear Turn Signal Lamps 305709441839
Stoplamps and Taillamps 305709441839
For replacement bulbs not listed here, contact your
retailer.
5-53
ProCarManuals.com

Removing the Flat Tire and
Installing the Spare Tire
You will need to remove the wheel cover or hubcap to
reach the wheel bolts.
For steel wheels with full plastic covers and aluminum
wheels with large circular center caps, do the following:
1. Loosen all plastic caps
by turning the wheel
wrench
counterclockwise. Do
not try to remove
plastic caps from the
cover or center cap.
2. Pull the cover or center cap away from the wheel
and place it in the trunk.When reinstalling full plastic covers or center caps,
tighten all plastic caps hand snug with the aid of
the wheel wrench and tighten them with the wheel
wrench an additional one-quarter of a turn.
1. Use the wheel wrench to loosen all the wheel nuts.
Do not remove them yet.
2. Attach the wheel
wrench to the jack bolt
head and rotate the
wheel wrench
clockwise. That will
raise the lift head
a little.
5-75
ProCarManuals.com

{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous without
the appropriate safety equipment and training.
The jack provided with your vehicle is
designed only for changing a at tire. If it is
used for anything else, you or others could be
badly injured or killed if the vehicle slips off
the jack. Use the jack provided with your
vehicle only for changing a at tire.
Notice:Make sure that the jack lift head is in the
correct position or you may damage your vehicle.
The repairs would not be covered by your warranty.5. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off the
ground so there is enough room for the road tire to
be removed.
5-77
ProCarManuals.com