2005 SAAB 9-7X clock

To replace one of these bulbs, do the following:
1. Open the hood. SeeHood Release on page 5-9
for more information.
2. Lift the two headlamp retaining clips to release the
headlamp assembly from the vehicle.
3. Pull the headlamp assembly away from the vehicle.
4. Remove the circular bulb cover for the high and
low-beam bulbs.5. Turn the bulb socket counterclockwise to remove it
from the headlamp assembly.
6. Pull the old bulb straight out of the bulb socket.
7. Install a new bulb and turn it clockwise to secure.
8. Reinstall the circular bulb covers, if necessary.
9. Reinstall the headlamp assembly by lining up the
headlamp assembly with the slots in the headlamp
retaining clips
10. Press down on the headlamp retaining clips to
secure the headlamp assembly.
HID Low-Beam Bulb Replacement
If your vehicle has HID low-beam headlamps and a bulb
needs to be replaced, see your dealer for replacement.
5-49
2005 - Saab 97X Owner Manual
ProCarManuals.com

Taillamps, Turn Signal, Sidemarker,
Stoplamps and Back-up Lamps
A. Back-up
B. Turn SignalC. Stoplamp/Taillamp
D. SidemarkerTo replace one of these bulbs, do the following:
1. Open the liftgate. SeeLiftgate/Liftglass on
page 2-13for more information.
2. Remove the screws
from the taillamp
assembly.
3. Pull the taillamp assembly away from the vehicle.
4. Turn the bulb socket counterclockwise to remove it
from the taillamp assembly.
5. Pull the old bulb straight out from the bulb socket.
5-50
2005 - Saab 97X Owner Manual
ProCarManuals.com

6. Press a new bulb into the bulb socket.
7. Insert the bulb socket into the taillamp assembly
and turn it clockwise to secure.
8. Reinstall the taillamp assembly into the vehicle and
tighten the two screws.
Replacement Bulbs
Exterior Lamp Bulb Number
Back-Up Lamp 921
Front Parking, Turn Signal Lamp 5702 NAK
Front/Rear Sidemarker 194
Halogen Headlamps
High-Beam 9005
Low-Beam (Halogen Only) H11
Rear Turn Signal 3757 AK
Stoplamp and Taillamp 3157
For replacement bulbs not listed here, contact your
dealer.
Windshield Replacement
Your vehicle is equipped with an acoustic windshield.
If you ever have to have your windshield replaced
be sure to get an acoustic windshield so you will
continue to have the benets an acoustic windshield
can provide.
Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected for wear
or cracking. SeeScheduled Maintenance on page 6-4.
Allowing the wiper blade arm to touch the windshield
when no wiper blade is installed could damage the
windshield. Any damage that occurs would not be
covered by your warranty. Do not allow the wiper blade
arm to touch the windshield.
5-51
2005 - Saab 97X Owner Manual
ProCarManuals.com

To use the accessory inator, do the following:
1. Attach the appropriate nozzle adapter to the end of
the hose if required.
2. Attach that end of the hose to the object you wish
to inate.
3. Attach the other end of the hose to the outlet.
4. Press and release the switch to turn the air inator
on. The indicator light will remain on when the
inator is running.
The system has an internal clock to prevent
overheating. The system will allow about
ve minutes of running time, then the compressor
will stop. The indicator light will then begin to
ash. When the indicator is off, the inator can be
started again by pressing the switch. If the
compressor is still hot, it may only run for a short
time before shutting off again.
5. Press and release the switch to turn the inator off.Place the inator kit tools in the pouch and store it in its
proper location. Remove the inator hose from the
outlet during loading and unloading. Load leveling will
not function with the inator hose attached to the inator
outlet. SeeElectronically Controlled Air Suspension
System on page 4-34for more information.
To reinstall the cover, line up the tabs at the back of the
cover, put it in place and latch the tabs.
A continuous ashing indicator light may also
indicate a malfunction in the air suspension system.
SeeElectronically Controlled Air Suspension System
on page 4-34for more information.
{CAUTION:
Inating something too much can make it
explode, and you or others could be injured.
Be sure to read the inator instructions, and
inate any object only to its recommended
pressure.
5-69
2005 - Saab 97X Owner Manual
ProCarManuals.com

Removing the Spare Tire and Tools
The jacking equipment you will need is stored under
the rear seat on the passenger’s side of the vehicle.
SeeRear Seat Operation on page 1-5for more
information.
To release the jack from its holder, turn the knob on the
jack counterclockwise to lower the jack head.The tools you will be using include the wheel wrench (A),
wheel blocks (B), extension(s), (socket end) (C),
handle (jack end) (D), and jack (E).
The following instructions explain how to remove the
underbody-mounted spare located underneath your
vehicle.
Notice:If you remove or restow a tire from/to the
storage position under the vehicle when it is
supported by a jack, you could damage the tire
and/or your vehicle. Always remove or restow a tire
when the vehicle is on the ground.
5-72
2005 - Saab 97X Owner Manual
ProCarManuals.com

1. Insert the socket end of the extension on a 45 degree
angle downward into the hoist drive shaft hole. It will
be exposed when the rear gate is open and is just
above the rear bumper. Be sure the socket end of the
extension connects to the hoist shaft.2. Turn the wheel wrench counterclockwise to lower
the spare tire. Keep turning the wheel wrench until
the spare tire can be pulled out from under the
vehicle.
If the spare tire does not lower to the ground,
the secondary latch is engaged causing the tire
not to lower. SeeSecondary Latch System
on page 5-79for more information.
3. Tilt the retainer at the end of the cable when
the tire has been completely lowered, and pull
it through the wheel opening.
4. Pull the tire out from under the vehicle.
Notice:If you drive away before the spare tire or
secondary latch system cable has been reinstalled,
you could damage your vehicle. Always reinstall
this cable before driving your vehicle.
5. Put the spare tire near the at tire.
5-73
2005 - Saab 97X Owner Manual
ProCarManuals.com

Removing the Flat Tire and
Installing the Spare Tire
1. Using the wheel
wrench, loosen all the
wheel nuts. Do not
remove them yet.
2. Turn the jack adjusting knob clockwise by hand to
raise the jack lift head.
3. Place the handle, extension and wheel wrench onto
the jack.A. Front Frame/Rear Axle
B. Jack
C. HandleD. Extension(s)
E. Wheel Wrench
4. Place the jack in the appropriate position nearest
the at tire.
FrontRear
5-74
2005 - Saab 97X Owner Manual
ProCarManuals.com

{CAUTION:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.
{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to t the
jack lift head into the proper location before
raising the vehicle.5. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off the
ground so there is enough room for the spare tire
to t.
6. Remove all the wheel nuts and take off the at tire.
5-75
2005 - Saab 97X Owner Manual
ProCarManuals.com