2005 MERCEDES-BENZ ML350 rear view mirror

106 Controls in detailMemory function*Storing positions into memory
Adjust the seat (
page 38) and exteri-
or rear view mirrors (page 41) to the
desired position.

Push memory button2 (
page 105).

Release memory button and press one
of the position buttons1 within three
seconds.
All the settings are stored at the select-
ed position.
Recalling positions from memory

Press and hold one of the position
buttons1 until seat and rear view mir-
rors have fully moved to the stored po-
sitions.
Storing exterior rear view mirror
parking position
For easier parking, you can adjust the pas-
senger-side exterior rear view mirror so
that you can see the right rear wheel as
soon as you engage reverse gearR.
For information on activating the parking
position feature, see “Activating exterior
rear view mirror parking position”
(page 129).Storing parking position

Stop the vehicle.

Switch on ignition (
page 33).

Press button2.
The passenger-side exterior rear view
mirror is selected.

Adjust the exterior rear view mirror
with button3 so that you see the rear
wheel and the road curb.

Press memory button2 (
page 105).

Within three seconds, press bottom of
adjustment button3.
The parking position is stored if the
mirror does not move.
!Do not operate the power seats using
the memory button if the seat backrest
is in an excessively reclined position.
Doing so could cause damage to front
or rear seats.
iReleasing the button immediately
stops movement to the stored posi-
tions.
iIf the mirror does move, repeat the
above steps. After the setting is stored
you can move the mirror again.
The selected position will be stored rel-
ative to the position button1
(page 105) pressed.

111 Controls in detail
Lighting
Locator lighting
With the locator lighting feature activated,
the following lamps will switch on when the
vehicle is unlocked by remote control dur-
ing darkness:

Tail and parking lamps


License plate lamps


Side marker lamps


Front fog lamps


Additional lamps in the exterior rear
view mirrors.
The locator lighting switches off when the
driver’s door is opened.
If you do not open a door after unlocking
by remote control the lamps will switch off
automatically after of approximately
40 seconds.

Turn the combination switch to
positionU when exiting the vehicle
(page 107).
The locator lighting is activated.High beam

Turn the combination switch to
positionõ or U (
page 107).

Push the combination switch in direc-
tion of arrow1 to switch on the high
beam (
page 107).
The high beam headlamp indicator
lampA in the instrument cluster
comes on.

Pull the combination switch in direction
of arrow2 to its original position to
switch off the high beam.
The high beam indicator lampA in
the instrument cluster goes out.
High beam flasher

Pull the combination switch briefly in
direction of arrow2 (
page 107).
Fog lampsWarning!
G
In low ambient lighting or foggy conditions,
only switch from positionU toõ with
the vehicle at a standstill. Switching
fromU toõ will briefly switch off the
headlamps. Doing so while driving in low
ambient lighting conditions may result in an
accident. iFog lamps will operate with the parking
lamps and / or low beam headlamps
on. Fog lamps should only be used in
conjunction with low beam headlamps.
Consult your State or Province Motor
Vehicle Regulations regarding permis-
sible lamp operation.

128 Controls in detailGood visibilityFor more information, see “Windshield
wipers” (
page 51) and “Mirrors”
(
page 41).
Rear view mirrors
Interior rear view mirror, antiglare
position
1Lever

Tilt the mirror to the antiglare night po-
sition by moving lever1 towards the
windshield.
The interior rear view mirror is dimmed.
Automatic antiglare rear view mirrors*
The reflection brightness of the exterior
rear view mirror on the driver’s side and
the interior rear view mirror will respond
automatically to glare when:


the automatic antiglare function is acti-
vated (
page 129)


the ignition is switched on


incoming light from headlamps falls on
the sensor in the interior rear view
mirror
The rear view mirror will not react if


reverse gear is engaged


the interior light is turned on
Warning!
G
The automatic antiglare function does not
react if incoming light is not aimed directly
at sensors in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver’s side do not
react, for example, if the cargo compart-
ment is fully loaded.
Glare can endanger you and others.Warning!
G
In the case of an accident, liquid electrolyte
may escape from the mirror housing if the
mirror glass breaks.
Electrolyte has an irritating effect. Do not al-
low the liquid to come into contact with
eyes, skin, clothing, or respiratory system.
In case it does, immediately flush affected
area with water, and seek medical help if
necessary.

129 Controls in detail
Good visibility
Activating
1Button
2Indicator lamp
Press button1.
Indicator lamp2 comes on.
Deactivating

Press button1 again.
Indicator lamp2 goes out.Activating exterior rear view mirror
parking position
The buttons are located on the lower part
of the center console.
1Deactivating parking position
2Activating parking position
3Adjustment button

Make sure you have stored a parking
position for the passenger-side exterior
rear view mirror (
page 106).

Switch on ignition (
page 33).

Press button2 for the passenger-side
exterior rear view mirror.
Warning!
G
Exercise care when using the passen-
ger-side exterior rear view mirror. The mirror
surface is convex (outwardly curved surface
for a wider field of view). Objects in mirror
are closer than they appear. Check your in-
terior rear view mirror or glance over your
shoulder before changing lanes.!Electrolyte drops coming into contact
with the vehicle paint finish can be
completely removed only while in the
liquid state and by applying plenty of
water.


130 Controls in detailGood visibility
Place the gear selector lever in reverse
gearR.
The passenger-side exterior rear view
mirror will be turned downward to the
stored position.
The exterior rear view mirror returns to its
previously stored driving position:


ten seconds after you put the gear
selector lever in positionD


immediately once you exceed a vehicle
speed of approx. 6 mph (10 km / h)


immediately when you press the
button1 for driver’s side mirrorElectrically folding exterior rear view
mirrors
Folding exterior mirrors in and out
manually*
The exterior rear view mirrors can vibrate if
they are not completely folded out.The buttons are located on the lower part
of the center console.
1Folds the exterior mirrors in
2Folds the exterior mirrors out

Switch on ignition (
page 33).
iIf the button1 is pressed, the auto-
matic passenger-side exterior rear view
parking position is deactivated.
!Before driving the vehicle through an
automatic car wash, fold the exterior
mirrors in. Otherwise they may get
damaged.
iWith the front doors closed, the exteri-
or mirrors can still be folded in and out
approximately 30 minutes after the ig-
nition has been turned off.


131 Controls in detail
Good visibility
Folding in
Briefly press button1 (
page 130).
The mirrors fold in.Folding out

Briefly press button2.
The mirrors fold out.
Windshield wipers
For more information on the windshield
wipers, see the “Getting started” section
(page 51).
!Before you drive the vehicle through an
automatic car wash, fold the exterior
mirrors in, otherwise they may get
damaged.iIf you are driving at more than approxi-
mately 9 mph (15 km / h), you will not
able to fold the exterior mirrors in.
!If an exterior rear view mirror housing
is forcibly pushed forward (hit from the
rear), reposition it manually by applying
firm pressure until it snaps back into
place.
If an exterior rear view mirror is forcibly
pushed rearward (hit from the front)
press button1 to fold mirrors in, then
press button2 to fold mirrors out. Do
not force mirrors by hand as this may
damage the adjustment mechanism.
The mirror housing is now properly po-
sitioned and you can adjust the mirror
normally.
!If leaves, snow, etc. block the wind-
shield wipers, the wiper motor turns
off.

For safety reasons, withdraw key
from steering lock. Remove block-
age.


Turn the windshield wipers on
again.
If windshield wipers fail to function at
all in switch position1,


set the wiper switch to the next
highest wiper speed.


have the windshield wipers
checked at the nearest authorized
Mercedes-Benz Light Truck Center.

176 Controls in detailUseful features
Emergency calls
An emergency call is initiated
automatically:

following an accident in which the
emergency tensioning detractors
(ETDs) or airbags deploy.
An emergency call can also be initiated
manually by opening the cover next to the
inside rear view mirror labeled SOS, then
briefly pressing the button located under
the cover. See (
page 178) for
instructions on initiating an emergency call
manually.
Warning!
G
The Tele Aid control unit is located under
the front passenger seat. If there is accumu-
lation of water or other liquid in this com-
partment, the Tele Aid control unit could
suffer an electrical short circuit making the
system inoperative. In this case the indica-
tor lamp in the SOS button will not illumi-
nate during or will remain illuminated after
the system self-check. Have the system
checked at the nearest Mercedes-Benz
Light Truck Center as soon as possible.
If the indicator lamps in the SOS button, in
the Roadside Assistance button and / or in
the Information button do not come on dur-
ing the system self-check or if any of these
indicators remain illuminated constantly in
red and / or the message
TELE AID -
VISIT WORKSHOP
is displayed in the MCS
display after the system self-check, a mal-
function in the system has been detected.
If a malfunction is indicated as outlined
above, the system may not operate as ex-
pected. Have the system checked at the
nearest Mercedes-Benz Light Truck Center
as soon as possible.

185 Controls in detail
Useful features
Programming or reprogramming the
integrated remote control
Step 1:
Switch on ignition.
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons3 and5 and release
them only when the indicator lamp6
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and / or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter1 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp6 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button2 and the desired integrated
signal transmitter button (3, 4
or5). Do not release the buttons until
completing step 5.
The indicator lamp6 on the integrat-
ed remote control will flash, first slowly
and then rapidly.
iFor operation in the USA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.