2005 MERCEDES-BENZ E320 Level

387 Practical hints
What to do if …
Display symbol
Display messages
Possible cause
Possible solution
:
USA only:Add 1 Qt. engine oil
at next refuelingCanada only:Add 1 Liter engine oil
at next refueling
The engine oil level is too low.

Add engine oil (
page 306) and
check the engine oil level
(
page 305).
Engine oil level
Stop, engine off
There is no oil in the engine. There is a
danger of engine damage.

Carefully bring the vehicle to a halt as
soon as possible.

Turn off the engine.

Add engine oil (
page 306) and
check the engine oil level
(
page 305).
Engine oil level
Reduce oil level
You have added too much engine oil.
There is a risk of damaging:

the engine


the catalytic converter (Gasoline en-
gine)


the oxidation catalyst (Diesel engine)

Have oil siphoned or drained off. Ob-
serve all legal requirements with re-
spect to its disposal.

388 Practical hintsWhat to do if …When the
Engine oil - Visit workshop

message appears while the engine is run-
ning and at operating temperature, the en-
gine oil level has dropped to approximately
the minimum level.
When this occurs, the warning will first
come on intermittently and then stay on if
the oil level drops further.If no oil leaks are noted, continue to drive
to the nearest service station where the
engine oil should be topped to the required
level with an approved oil specified in the
Factory Approved Service Products pam-
phlet.
Display symbol
Display messages
Possible cause
Possible solution
:
Engine oil
Visit workshop
The engine oil has dropped to a critical
level.

Check the engine oil level
(page 305) and add oil as required
(page 306).

If you must add engine oil frequently,
have the engine checked for possible
leaks.
It may be that there is water in the engine
oil.

Have the engine oil checked.
Engine oil level
Visit workshop
The measuring system is malfunctioning.

Have the measuring system checked
by an authorized Mercedes-Benz
Center.!The engine oil level warnings should
not be ignored. Extended driving with
the symbol displayed could result in
serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.

389 Practical hints
What to do if …
Display symbol
Display messages
Possible cause
Possible solution
A
Reserve fuel
The fuel level has dropped below the re-
serve mark.

Refuel at the next gas station
(page 299).
Check gas cap
See Operator’s Manual
A loss of pressure has been detected in
the fuel system. The fuel cap may not be
closed properly or the fuel system may be
leaky.

Check the fuel cap (
page 299).
If it is not closed properly:

Close the fuel cap.
If it is closed properly:

Have the fuel system checked by an
authorized Mercedes-Benz Center.
Y
Hood open
You are driving with the hood open.

Close the hood (
page 303).

405 Practical hints
What to do if …
Display symbol
Display messages
Possible cause
Possible solution
t
Function
unavailable
This display appears if button t or
s on the multifunction steering wheel
is pressed and the vehicle is not equipped
with a telephone.
Ê
Trunk open
This message will appear whenever the
trunk lid is open.

Close the trunk lid.
W
Washer fluid,
please refill
The fluid level has dropped to about
1/3
of total reservoir capacity.
Add washer fluid (
page 310).

406 Practical hintsWhat to do if …Display symbol
Display messages
Possible cause
Possible solution
@
Vehicle rising
Your vehicle is adjusting to your level se-
lection.
Leveling cancelled
The “Raised” level setting is canceled at
vehicle speeds of over 75 mph
(120 km / h).

Reactivate the “Raised” level setting.
Stop, car too low
The vehicle level control is malfunction-
ing.
Avoid excessive steering input. The fend-
er or tires could otherwise be damaged.
Listen for scraping noises. Do not drive
faster than 50 mph (80 km / h).
Drive to the side of the road and se-
lect a higher vehicle level. Depending
on the type of malfunction, this may
raise the vehicle’s level.
There is otherwise danger of an accident.
Visit workshop
The system is functional only to a limited
extent.
The system display or the system is mal-
functioning.

Do not drive faster than 50 mph
(80 km / h).

Have the vehicle checked at an autho-
rized Mercedes-Benz Center.

421 Practical hints
Replacing bulbs
Low beam bulb (halogen headlamps
only)
Turn housing cover3 counterclock-
wise and remove it.

Pull electrical connector7 off.

Unclip the retainer spring on the bulb
socket and take out the bulb.

Insert the new bulb so that its base lo-
cates in the recess on the lower left
and is level to it.

Clip on the retainer spring.

Plug electrical connector7 onto the
bulb.

Align housing cover3 and turn it
clockwise.
High beam bulb/high beam flasher
bulb (halogen headlamps)/high beam
flasher bulb (Bi-Xenon* headlamps)

Turn bulb socket1 with the bulb
counterclockwise and remove it.

Pull electrical connector5 off.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket1.

Press the new bulb gently into bulb
socket1 and turn clockwise until it
engages.

Plug electrical connector5 onto the
bulb.

Place bulb socket1 back into the
lamp and turn it clockwise.
Front turn signal lamp bulb

Turn bulb socket4 with the bulb
counterclockwise and remove it.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket4.

Press the new bulb gently into bulb
socket4 and turn clockwise until it
engages.

Place bulb socket4 back into the
lamp and turn it clockwise.Parking and standing lamp bulb

Pull out bulb socket6 with the bulb.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket6.

Press the new bulb gently into bulb
socket6 and turn clockwise until it
engages.

Press bulb socket6 back into the
lamp.

425 Practical hints
Flat tire
Flat tire
In the case of a flat tire, you may tempo-
rarily use the spare wheel when observing
the following restrictions:

Do not exceed a vehicle speed of
50 mph (80 km / h).


Drive to the nearest tire repair facility
to have the flat tire repaired or re-
placed as appropriate.


Do not operate vehicle with more than
one spare wheel mounted.
Preparing the vehicle
Park the vehicle as far as possible from
moving traffic on a hard surface.

Turn on the hazard warning flashers.

Engage the steering wheel lock in the
straight-ahead position and set the
parking brake.

Move the selector lever toP.

Have any passenger exit the vehicle at
a safe distance from the roadway.
Mounting the spare wheel
Preparing the vehicle
Prepare the vehicle as described under
“Preparing the vehicle” on this page.
Take the spare wheel out of the trunk
(page 407).

Take the wheel wrench and the jack
out of the trunk (
page 407).
Lifting the vehicle

Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizable objects.
When changing wheel on a level surface:

Place one chock in front of and one be-
hind the wheel that is diagonally oppo-
site to the wheel being changed.
Warning!
G
The dimensions of the Minispare wheel and
the collapsible tire are different from those
of the road wheels. As a result, the vehicle
handling characteristics change when driv-
ing with a spare wheel mounted.
The spare wheel should only be used tempo-
rarily, and replaced with a regular road
wheel as quickly as possible.

426 Practical hintsFlat tireWhen changing wheel on a hill:
Place chocks on the downhill side
blocking both wheels of the other axle.

On wheel to be changed, loosen but do
not yet remove the wheel bolts (ap-
proximately one full turn with wrench). The jack take-up brackets are located di-
rectly behind the front wheel housing and
in front of the rear wheel housing.
1Jack take-up bracket
2Jack
3Crank

Position jack2 on firm ground under
the respective jack take-up bracket1.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into either side of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Be sure that the jack arm is
fully seated in the jack take-up bracket. Al-
ways lower the vehicle onto sufficient ca-
pacity jackstands before working under the
vehicle.