2005 MERCEDES-BENZ CLK500 CABRIOLET display

236 Controls in detailAudio systemTerminating a call
Press t button.
The current call is terminated and the
muted audio source becomes active
again.
Accepting a second incoming call
If you receive another call during an al-
ready active call, you can accept the sec-
ond call and switch between the two.


Accepting a second call
Place new call by entering tele-
phone number manually.
You are connected to the second
caller; the first caller is kept on hold.


Switching between calls
Press s button.
This switches between the calls.
The non-active call is kept on hold.


Terminating a call
Press t button.
The current call is terminated. The
connection to the caller previously
kept on hold is also interrupted;
however, reconnection is indicated
by an acoustic signal.
Placing a second call
If you wish to place another call during an
already active call, you can place the sec-
ond call and switch between the callers or
combine them into one call. Note that this
feature is depending on availability from
your mobile phone service provider.


Placing a second call
Place a new call by entering tele-
phone number manually.

Press s button.
You are connected to the second
caller; the first caller is kept on
hold.


Terminating a call
Press t button.
The current call is terminated. The
connection to the caller previously
kept on hold is also interrupted;
however, reconnection is indicated
by an acoustic signal.


Combining two calls
Press s button.
The calls are combined into one
call.


Terminating a combined call
Press t button.
The connection to both callers is
terminated.
iYou will be notified of the second call
acoustically, but you will not see this in
the display.

237 Controls in detail
Audio system
Emergency calls “911”
The following describes how to dial a “911”
emergency call using the audio system
head unit when a Mercedes-Benz specified
mobile phone* is inserted in the phone
cradle*. Unless otherwise specified, the
descriptions refer to the audio system
head unit.
Consult the separate telephone operating
instructions that came with your mobile
phone* for information on how to place a
“911” emergency call on the mobile
phone*. The following conditions must be met for a
“911” emergency call:


Telephone must be switched on.


The corresponding mobile communica-
tions network must be available.
If you cannot make an emergency call, you
will have to initiate rescue measures your-
self. GSM network phones
Placing a “911” emergency call using
audio head unit with the phone locked

Press hbutton to switch to tele-
phone operation. PIN?
appears in the audio display.

Enter 911 using the number keypad on
the audio head unit.

Press
OK soft key or sbutton for
dialing to begin.
DIALING
appears in the audio display
while the telephone establishes the
connection.

Wait until the emergency call center
answers, then describe the emergency.
Warning!
G
The “911” emergency call system is a public
service. Using it without due cause is a crim-
inal offense.
iEmergency calls may not be possible
with all telephone networks or if certain
network services and/or telephone
functions are active. Check with your
local service providers.

238 Controls in detailAudio systemPlacing a “911” emergency call using
audio head unit with the phone un-
locked
Press hbutton to switch to tele-
phone operation.

Enter 911 using the number keypad on
the audio head unit.

Press sbutton for dialing to begin. DIALING
appears in the audio display
while the telephone establishes the
connection.

Wait until the emergency call center
answers, then describe the emergency. TDMA/CDMA network phones
Placing a “911” emergency call using
audio head unit with the phone locked

Press hbutton to switch to tele-
phone operation. CODE?
appears in the audio display.

Enter 911 using the number keypad on
the audio head unit.

Press
OK soft key or sbutton for di-
aling to begin.
DIALING
appears in the audio display
while the telephone establishes the
connection.

Wait until the emergency call center
answers, then describe the emergency. Placing a “911” emergency call using
audio head unit with the phone un-
locked

Press hbutton to switch to tele-
phone operation.

Enter 911 using the number keypad on
the audio head unit.

Press sbutton for dialing to begin.DIALING
appears in the audio display
while the telephone establishes the
connection.

Wait until the emergency call center
answers, then describe the emergency.
iIf no SIM card is in the mobile phone, NO SERVICE
appears in the audio dis-
play. In that case, you only can make an
emergency call on the mobile phone it-
self, without the use of the head unit.

247 Controls in detail
Soft top
Opening the soft top
1Soft top opening
Before pulling on the soft top switch, you
must make sure:

the parking brake is engaged
(page 49)


the luggage cover is latched, see
“Latch luggage cover” (
page 245)


the ski sack roller blind is closed, see
“Closing ski sack roller blind”
(page 246)


the trunk lid is closed


the ignition is switched on (
page 36)

Pull up on the soft top switch as indi-
cated by the arrow1 until the soft top
is completely lowered into its trunk
storage compartment.
During the opening procedure the mul-
tifunction display shows the message Top in operation
.
If the opening procedure is finished,
the multifunction display will briefly
show the message Top open
.
If you continuously pull on the soft top
switch, the windows will close.
However, the windows can also be
closed/opened later on, for more informa-
tion see “Opening and closing the windows
with the soft top switch” (
page 241), or
see “Opening and closing the windows”
(
page 239).
iThe soft top cannot be opened using
the soft top switch when the roll bars
have been released. The roll bars need
to be lowered before the soft top can
be operated again using the soft top
switch. If the roll bars have released
and the soft top is closed, contact an
authorized Mercedes-Benz Center to
have the roll bars lowered. Do not at-
tempt to lower the roll bars manually
with the soft top closed. Lowering the
roll bars manually with the soft top
closed may impair the function of the
roll bars (
page 401).
If the roll bars have released and the
soft top is open, you can lower the roll
bars manually (
page 402) or contact
an authorized Mercedes-Benz Center
to have the roll bars lowered.

249 Controls in detail
Soft top

Press the soft top switch as indicated
by the arrow1 until the soft top is
completely closed and locked.
During the closing procedure the multi-
function display shows the message Top in operation
.
If the soft top is closed and locked, the
multifunction display will briefly show
the message
Top closed
.
If you continuously press on the soft
top switch the windows will close.
However, the windows can also be
closed/opened later on, for more informa-
tion see “Opening and closing the windows
with the soft top switch” (
page 241) or
see “Opening and closing the windows”
(
page 239).iFor safety reasons, the soft top cannot
be opened while driving.
iThe soft top cannot be closed using the
soft top switch when the roll bars have
been released. The roll bars need to be
lowered before the soft top can be op-
erated again using the soft top switch.
If the roll bars have released and the
soft top is open, you can lower the roll
bars manually (
page 402) or contact
an authorized Mercedes-Benz Center
to have the roll bars lowered.
Warning!
G
To prevent possible accidents, drive the ve-
hicle only with the soft top either completely
closed and locked, or fully lowered into its
storage compartment.
If the soft top does not completely open or
close, a warning sounds. In the multifunc-
tion display you will see K, and the mes-
sage
Top being lowered!
appears. After
about 15 seconds the roof hydraulics lose
pressure.
Properly lock the soft top (page 250) be-
fore continuing to drive.

250 Controls in detailSoft topLocking the soft top after raising/low-
ering
If the soft top is not properly locked, lock it
as described below.Unlocked status noticed when stopped

Switch on the ignition (
page 36).

To lock the soft top in its fully closed
position, press soft top switch.
The message
Top closed
will be shown
in the multifunction display.
or:

To lock the soft top in its fully opened
position, pull up on the soft top switch.
The message
Top open
will be shown in
the multifunction display.Unlocked status noticed while driving

Stop the vehicle.

Leave the ignition switched on.

To lock the soft top in its fully closed
position, press soft top switch.
The message
Top closed
will be shown
in the multifunction display.
or:

To lock the soft top in its fully opened
position, pull up on the soft top switch.
The message
Top open
will be shown in
the multifunction display.
Warning!
G
The soft top is not fully closed and locked or
not fully opened if:

the message
Top in operation!
is
shown in the multifunction display


a warning sounds for 10 seconds and
the message
Lock top
is shown in the
multifunction display when starting to
drive
To prevent possible accidents, drive the ve-
hicle only with the soft top either completely
closed and locked, or fully lowered into its
storage compartment.
Warning!
G
Stop the vehicle and lock the soft top before
continuing to drive. You could otherwise en-
danger yourself and others.

252 Controls in detailSoft topOpening (Summer opening feature)
Press and hold button Πuntil the
soft top is completely open.
The windows and soft top begin to
open after approximately one second.
During the opening procedure the mul-
tifunction display shows the message Top in operation
.
If the opening procedure is finished,
the multifunction display will briefly
show the message Top open
.

Release transmit button Πto inter-
rupt procedure.Closing (Convenience feature)

Press and hold button ‹ until the
soft top is completely closed.
The windows and soft top begin to
close after approximately one second.
During the closing procedure the multi-
function display shows the message Top in operation
.
If the soft top is closed and locked, the
multifunction display will briefly show
the message
Top closed
.

Release transmit button ‹ to inter-
rupt procedure.
Make sure all side windows and the
soft top are properly closed before leaving
the vehicle.
Warning!
G
If the soft top does not completely open or
close, a warning sounds and the soft top
switch flashes. In the multifunction display
you will see K, and the message
Top
being lowered!
appears. After about
15 seconds the roof hydraulics lose pres-
sure.
Properly lock the soft top (
page 250) be-
fore continuing to drive.

256 Controls in detailDriving systems1Set current or higher speed
2Set current or lower speed
3Cancel cruise control
4Resume to last set speedSetting current speed

Accelerate or decelerate to the desired
speed.

Briefly lift1 or depress2 the cruise
control lever (
page 256).
The current speed is set.

Remove your foot from the accelerator
pedal.
Cruise control is activated.
The selected speed appears in the multi-
function display for approximately five sec-
onds, and the corresponding speedometer
segments from the selected speed to the
vehicle maximum speed are illuminated.
Warning!
G
CLK 500:
Cruise control brakes automatically so that
the set speed is not exceeded. The brake
pedal is depressed automatically to do this.
Keep in mind that cruise control is a conve-
nience system designed to assist the driver
during vehicle operation. The driver is and
must always remain responsible for the ve-
hicle’s speed and for safe brake operation.
Keep driver’s foot area clear at all times, in-
cluding the area under the brake pedal. Ob-
jects stored in this area may impair pedal
movement which could interfere with the
braking ability of the cruise control system.
Do not place your foot under the brake pedal
- your foot could become caught.