2005 MERCEDES-BENZ CLK500 CABRIOLET remote start

32 Getting startedThe “Getting started” section provides an
overview of the vehicle’s most basic func-
tions. First-time Mercedes-Benz owners
should pay special attention to the infor-
mation given here.
If you are already familiar with the basic
functions described here, the “Controls in
detail” section will provide you with further
information. The corresponding page
references are located at the end of each
segment.Unlocking
Unlocking with the SmartKeySmartKey with remote control 1‹Lock button
2ŠOpening button for trunk lid
3ŒUnlock button
4ÂPanic button (
page 83)

Press unlock button Πon the
SmartKey.
All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system is
disarmed.

Enter the vehicle and insert the
SmartKey in the starter switch.For more information, see “SmartKey”
(
page 94).Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle.
Unsupervised use of vehicle equipment may
cause an accident and/or serious personal
injury.iOpening a door causes the windows on
that side of the car to open slightly.
They will return to the up position when
the door is closed.

94 Controls in detailIn the “Controls in detail” section you will
find detailed information on how to oper-
ate the equipment installed on your vehi-
cle. If you are already familiar with the
basic functions of your vehicle, this section
will be of particular interest to you.
To quickly familiarize yourself with the ba-
sic functions of the vehicle, refer to the
“Getting started” section of this manual.
The corresponding page numbers are giv-
en at the beginning of each segment.Locking and unlocking
For more information on locking and
unlocking, see “Getting started”
(page 32) and (
page 55).
SmartKey
Your vehicle comes supplied with two
SmartKeys, each with remote control and
a removable mechanical key.
The locking tabs for the mechanical key
portion of the two SmartKeys are a
different color to help distinguish each
SmartKey unit.
The SmartKey provides an extended oper-
ating range. To prevent theft, however, it is
advisable to only unlock the vehicle when
you are in close proximity to it.
The SmartKey centrally locks and unlocks:

the doors


the glove box


the trunk lid


the fuel filler flap
SmartKey with remote control1‹ Lock button
2Š Opening button for trunk lid
3Mechanical key locking tab
4ΠUnlock button
5Battery check lamp
6Â Panic button (
page 83)

286 Controls in detailUseful featuresProgramming or reprogramming the in-
tegrated remote control
Step 1:
Switch on the ignition (
page 36).
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp 1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.

288 Controls in detailUseful featuresGate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.
Operation of integrated remote control

Switch on the ignition (
page 36).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the integrated remote control
memory

Switch on the ignition (
page 36).

Simultaneously hold down the signal
transmitter buttons2 and 4, for ap-
proximately 20 seconds, until the indicator lamp1 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.
Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (2, 3 or4). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.iIf you sell your vehicle, erase the codes
of all three channels.

475 Index
E
Easy-entry/exit feature 112
Activating 156
Electrical fuses 436
Electrical outlet in
rear passenger compartment 275
Electrical system
Technical data 450
Electronic Stability Program see ESP
Emergency call
911 237
Emergency call system* 277
Emergency calls
Initiating an emergency call 279
With Tele Aid 278
Emergency operation
(Limp Home Mode) 175
Emergency operations
Closing soft top 403
Locking the vehicle 398
Remote door unlock 283
Unlocking the vehicle 397
Emergency tensioning device see ETD
Emission control 300
Emission control information label 442Ending
A call (telephone*) 161
Engine
Compartment 305
Message in display 356
Starting 47
Starting with KEYLESS-GO* 47
Starting with the SmartKey 47
Technical data 444
Turning off 56
Engine cleaning 347
Engine compartment 305
Fuse box in 437
Hood 305
Engine malfunction
indicator lamp 25, 356
Engine number 442, 462Engine oil 306, 455
Adding 309
Additives 455
Checking level 307
Consumption 306
Filler cap 309
Filler neck 309
Message in display 380
Messages in display 308
Viscosity 462
Engine oil level see Oil level
ESP 25, 86, 462
Messages in display 368
Switching off 87
Switching on 88
Warning lamp 358
ETD 462
Safety guidelines 64
ETD (Emergency tensioning device) 70
Exterior lamp switch 122
Exterior rear view mirrors
Adjusting 41
Parking position for 157

479 Index
Instrument cluster 24, 130, 463
Cleaning 351
Coolant temperature indicator 131
Illumination 130
Lamps in 354–360
Multifunction display 133
Outside temperature indicator 132
Selecting language 146
Instruments and controls see Cockpit
Interior lighting 128
Activating automatic control 128
Deactivating automatic control 129
Delayed switch-off 154
Manual operation 129
Interior rear view mirror
Adjusting 41
Intermittent wipe 53J
Jack 391, 393
Jump starting 430
K
Key 209
Key, mechanical 397
Key, SmartKey with KEYLESS-GO*
Replacing the batteries 413
Key-dependency memory
Settings 157
KEYLESS-GO* 463
Activating ignition with 36
Closing side windows with 243
Closing windows with 243
Factory setting 101
Global locking 102
Global unlocking 101
Important notes 100
Messages in display 382
Remote control 98Starting the engine 47
Turning off the engine 57
Unlocking with 33
Unlocking, trunk lid 104
Kickdown 170, 463
Kilometers/miles in speedometer 145
Kilopascal 336
Km/h or mph in speedometer 145
L
Labels, identification 442
Lamp bulbs, exterior 414
Lamp sensor
Messages in display 384
Lamps, exterior
Front 414
Light sensor 384
Messages in display 383–386
Rear 415

489 Index
Side windows
Automatic opening 240
Cleaning 350
Closing 239, 240, 241, 242
Closing with KEYLESS-GO* 243
Closing with SmartKey 242
Closing with soft top switch 241
Opening 239, 240, 241, 242
Opening fully 240
Opening with SmartKey 242
Opening with soft top switch 241
Stopping 241
Synchronizing power windows 243
Sidewall 337
Simultaneous wiping and washing
Windshield wipers 53
Single CD mode selector 203
Single wipe 53
Ski sack roller blind* 246
Closing 246, 267
Opening 246, 264
Ski sack* 264
Removing 267
Unfolding and loading 264
Unloading and folding 266SmartKey 94
Battery check lamp 96, 102
Checking the batteries 97, 103
Closing soft top 252
Factory setting 96
Global locking 96
Global unlocking 96
Locking and unlocking 94
Loss of 98
Message in display 382
Opening and closing
windows with 242
Opening soft top 251
Positions in starter switch 34
Remote control 94, 99
Replacing the batteries 412
Restoring to factory setting 97, 103
Selective setting 96, 102
Starting the engine 47
Turning off the engine 56
Unlocking with 32SmartKey with KEYLESS-GO*
Checking the batteries 97, 103
Global locking
and unlocking 101, 102
Loss of 105
Message in display 382
Messages in display 382
Remote control 98
Restoring to factory setting 97, 103
Turning off the engine 57
Unlocking with 33
Snow chains 341
Soft keys
Audio system 204