2005 MERCEDES-BENZ CLK320 COUPE remote start

32 Getting startedThe “Getting started” section provides an
overview of the vehicle’s most basic func-
tions. First-time Mercedes-Benz owners
should pay special attention to the infor-
mation given here.
If you are already familiar with the basic
functions described here, the “Controls in
detail” section will provide you with further
information. The corresponding page
references are located at the end of each
segment.Unlocking
Unlocking with the SmartKeySmartKey with remote control 1‹Lock button
2ŠOpening button for trunk lid
3ŒUnlock button
4ÂPanic button (
page 83)

Press unlock button Πon the
SmartKey.
All turn signal lamps flash once. The
locking knobs in the doors move up.

Enter the vehicle and insert the
SmartKey in the starter switch.For more information, see “SmartKey”
(
page 94).Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle.
Unsupervised use of vehicle equipment may
cause an accident and/or serious personal
injury.iOpening a door causes the windows on
that side of the car to open slightly.
They will return to the up position when
the door is closed.

94 Controls in detailIn the “Controls in detail” section you will
find detailed information on how to oper-
ate the equipment installed on your vehi-
cle. If you are already familiar with the
basic functions of your vehicle, this section
will be of particular interest to you.
To quickly familiarize yourself with the ba-
sic functions of the, refer to the “Getting
started” section of this manual. The corre-
sponding page numbers are given at the
beginning of each segment.Locking and unlocking
For more information on locking and
unlocking, see “Getting started”
(page 32) and (
page 55).
SmartKey
Your vehicle comes supplied with two
SmartKeys, each with remote control and
a removable mechanical key.
The locking tabs for the mechanical key
portion of the two SmartKeys are a
different color to help distinguish each
SmartKey unit.
The SmartKey provides an extended oper-
ating range. To prevent theft, however, it is
advisable to only unlock the vehicle when
you are in close proximity to it.
The SmartKey centrally locks and unlocks:

the doors


the trunk


the fuel filler flap
SmartKey with remote control1‹ Lock button
2Š Opening button for trunk lid
3Mechanical key locking tab
4ΠUnlock button
5Battery check lamp
6Â Panic button (
page 83)

289 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on ignition (
page 36).
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.

291 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner. If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:

Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.

292 Controls in detailUseful featuresOperation of integrated remote control
Switch on ignition (
page 36).

Select and press the appropriate
integrated signal transmitter button
(2, 3 or4) to activate the remote
controlled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.Erasing the integrated remote control
memory

Switch on ignition (
page 36).

Simultaneously hold down the signal
transmitter buttons2 and 4, for
approximately 20 seconds, until the
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

The indicator lamp will begin to flash
after 20 seconds. Without releasing
the integrated signal transmitter
button, proceed with programming
starting with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

469 Index
E
Easy-entry/exit feature 112
Activating 159
Electrical fuses 429
Electrical outlet in
rear passenger compartment 278
Electrical system
Technical data 444
Electronic Stability Program see ESP
Emergency call
911 245
Emergency call system* 280
Emergency calls
Initiating an emergency call 282
With Tele Aid 281
Emergency operation
(Limp Home Mode) 177
Emergency operations
Closing
power tilt/sliding sunroof* 401
Locking the vehicle 398
Opening
power tilt/sliding sunroof* 401
Remote door unlock 286
Unlocking the vehicle 397Emergency tensioning device see ETD
Emission control 304
Emission control information label 436
Ending
A call (telephone) 163
Engine
Compartment 308
Message in display 356
Starting 47
Starting with KEYLESS-GO* 47
Starting with the SmartKey 47
Technical data 438
Turning off 56
Engine cleaning 349
Engine compartment 308
Fuse box in 431
Hood 308
Engine malfunction
indicator lamp 25, 356
Engine number 436, 456Engine oil 309, 449
Adding 312
Additives 449
Checking level 310
Consumption 309
Filler cap 312
Filler neck 312
Message in display 379
Messages in display 311
Viscosity 456
Engine oil level see Oil level
ESP 25, 86, 456
Messages in display 367
Switching off 87
Switching on 88
Warning lamp 358
ETD 69, 456
Safety guidelines 64
Exterior lamp switch 124
Exterior rear view mirrors
Adjusting 41
Parking position for 160

473 Index
Instrument cluster 24, 134, 457
Cleaning 351
Coolant temperature indicator 135
Illumination 134
Lamps in 354–359
Multifunction display 137
Outside temperature indicator 136
Selecting language 150
Instruments and controls see Cockpit
Interior lighting 132
Activating automatic control 132
Deactivating automatic control 132
Delayed switch-off 157
Manual operation 133
Interior rear view mirror
Adjusting 41
Auto-dimming 178
Interior storage compartments 272
Intermittent wipe 53
J
Jack 389
Jump starting 423K
Key, mechanical 397
Key, SmartKey with KEYLESS-GO*
Replacing the batteries 403
Key-dependency memory
Settings 160
KEYLESS-GO* 457
Activating ignition with 36
Closing power
tilt/sliding sunroof* with 250, 253
Closing windows with 250, 253
Factory setting 101
Global locking 101
Global unlocking 101
Important notes 100
Locking the vehicle 103
Messages in display 381
Remote controls 99
Starting the engine 47
Turning off the engine 57
Unlocking with 33
Unlocking, trunk lid 104
Kickdown 171, 457
Kilometers/miles in speedometer 149
Kilopascal 339
Km/h or mph in speedometer 149L
Labels, identification 436
Lamp bulbs, exterior 404
Lamp sensor
Messages in display 383
Lamps, exterior
Front 404
Light sensor 383
Messages in display 382–385
Rear 405
Lamps, indicator and warning
ABS 354
Battery (SmartKey) 96, 102
Brakes 355
Center console 360
CHECK ENGINE 356
Coolant 357, 375
Engine diagnostics 356
ESP 358
Front passenger front
air bag off indicator lamp 66, 360
Fuel reserve 359
Instrument cluster 354–359

483 Index
Speedometer display mode 149
Temperature (Interior) 187
Temperature (interior) 197
Temperature indicator 149
To last stored speed
("Resume" function)
in cruise control 259
Units
Speedometer 149
Temperature 149
Setting current speed 256
Setting the temperature 187
Settings
Convenience functions 158
Factory, KEYLESS-GO* 101
Factory, SmartKey 96
Individual (SmartKey) 160
Lighting (control system) 154
Menus and submenus 139
Resetting all (control system) 146
Resetting in the submenu 147
Selective 96, 102
Settings menu
Functions in 146
Individual vehicle settings 146
Submenus 147Shift lock 459
Shifting
Gear selector lever 165
Gear selector lever positions 169
Into optimal gear range
(Automatic transmission) 167
Side impact air bags 66
Side marker lamps
Replacing bulbs 404, 405, 409
Side windows
Automatic opening 248
Cleaning 351
Closing 247, 248, 249
Closing with KEYLESS-GO* 250, 253
Closing with SmartKey 249
Opening 247, 248, 249
Opening fully 248
Opening with SmartKey 249
Stopping 249
Synchronizing power windows 250
Sidewall 339
Simultaneous wiping and washing
Windshield wipers 53
Single wipe 53Ski sack* 264
Removing 267
Unfolding and loading 264
Unloading and folding 266
SmartKey 94
Battery check lamp 96, 102
Checking the batteries 97, 103
Factory setting 96
Global locking 96
Global unlocking 96
Locking and unlocking 94
Loss of 98
Message in display 381
Opening and closing the power
tilt/sliding sunroof* with 253
Opening and closing
windows with 249
Positions in starter switch 34
Remote controls 94
Replacing the batteries 402
Restoring to factory setting 97, 102
Selective setting 96, 102
Starting the engine 47
Turning off the engine 56
Unlocking with 32