2005 MERCEDES-BENZ C CLASS COUPE clock

388 Practical hintsReplacing bulbsFront turn signal lamp bulb
Turn bulb socket3 counterclockwise
and remove it.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket 3.

Press the new bulb gently into bulb
socket 3 and turn clockwise until it
engages.

Place bulb socket 3 back into the
lamp and turn it clockwise. Parking and standing lamp bulb

Turn housing cover
2 counterclock-
wise and remove it.

Pull out bulb socket 6 with the bulb.

Pull the bulb out of bulb socket 6.

Press the new bulb into bulb socket 6.

Press bulb socket 6 back into the
lamp.

Align housing cover 2 and turn it
clockwise. Bi-Xenon* headlamps
Warning!
G
Do not remove the cover
1
for the
Bi-Xenon headlamp. Because of high voltage
in Bi-Xenon lamps, it is dangerous to replace
the bulb or repair the lamp and its compo-
nents. We recommend that you have such
work done by a qualified technician.

389
Practical hints
Replacing bulbs
Left headlamp, mirror-image of right
headlamp1
Housing cover for Bi-Xenon headlamp
2 Housing cover for high beam flasher,
parking and standing lamp 3
Bulb socket for turn signal lamp
4 Bulb holder for high beam flasher
5 Bulb socket for parking and standing
lamp bulb
High beam bulb for high beam flasher

Turn housing cover 2 counterclock-
wise and remove it.

Turn bulb holder 4 with the bulb coun-
terclockwise and remove it.

Pull the bulb at its socket out of bulb
holder 4.

Insert the new bulb so that its socket
locates in the recess of bulb holder 4
and is level to it.

Reinsert bulb holder 4 w i t h t h e b u l b i n
the lamp and turn clockwise.

Align housing cover 2 and turn it
clockwise.
Front turn signal lamp bulb

Turn bulb socket 3 with the bulb
counterclockwise and remove it.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket 3.

Press the new bulb gently into bulb
socket 3 and turn clockwise until it
engages.

Place bulb socket 3 back into the
lamp and turn it clockwise.

390 Practical hintsReplacing bulbsParking and standing lamp bulb
Turn housing cover2 counterclock-
wise and remove it.

Pull out bulb socket 5 with the bulb.

Pull the bulb out of bulb socket 5.

Press the new bulb into bulb socket 5.

Press bulb socket 5 back into the
lamp.

Align housing cover 2 and turn it
clockwise. Side marker lamp bulb

Carefully slide the lamp towards the
rear in direction of arrows.

Remove the front end first.

Turn the bulb socket with the bulb
counterclockwise and remove it.

Pull the bulb out of the bulb socket.

Insert the new bulb into the bulb sock-
et.

Place the bulb socket back into the
lamp and turn it clockwise.

To reinstall the lamp, set the rear end in
the bumper and let the front end en-
gage.
Replacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
position
M (
page 110).
Tail lamp unit
1 Trim panel
2 Latch

Open the trunk lid.

Turn latches 1 on respective trim
panel 2 clockwise.

Fold trim panel 2 to the side.

391
Practical hints
Replacing bulbs
3
Tab
4 Bulb socket for side marker lamp bulb
Press tabs 3 together.

Remove the bulb carrier.

Press gently onto the respective bulb
and turn counterclockwise out of its
bulb socket.

Press the new bulb gently into its bulb
socket and turn clockwise until it en-
gages. 5
Brake lamp bulb
6 Backup lamp bulb
7 Turn signal lamp bulb
8 Rear fog lamp bulb (only driver’s side),
tail, parking and standing lamp

Reinstall the bulb carrier.
Let tabs 3 engage.

Reinstall trim panel 2.

Turn latches 1 counterclockwise. Side marker lamp
The bulb socket for the side marker lamp
bulb is located between the bulb carrier
and the vehicle’s body.

Open the trunk lid.

Turn latches
1 on respective trim
panel 2 clockwise.

Fold trim panel 2 to the side.

Pull bulb socket 4 with the bulb out of
its holder.

Pull the bulb out of bulb socket 4.

Press the new bulb into bulb socket 4.

Press bulb socket 4 back into its
holder.

Reinstall trim panel 2.

Turn latches 1 counterclockwise.

400 Practical hintsFlat tireLowering the vehicle
Lower vehicle by turning crank coun-
terclockwise until vehicle is resting ful-
ly on its own weight.

Remove the jack.1
-5 Wheel bolts

Tighten the five wheel bolts evenly, fol-
lowing the diagonal sequence
illustrated ( 1 to 5 ), until all bolts are
tight. Observe a tightening torque of
80 lb-ft (110 Nm). Before storing the jack, it should be fully
collapsed, with handle folded in (storage
position) (
page 374).

Store the jack, the damaged wheel and
the other vehicle tools in the wheel well
below the trunk floor (
page 375).
Warning!
G
Inflate spare wheel with collapsible tire only
after the wheel is properly mounted.
Inflate the spare wheel tire using the electric
air pump before lowering the vehicle.
Warning!
G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
80 lb-ft (110 Nm).

403
Practical hints
Battery
Reconnecting the battery
Turn off all electrical consumers.

Remove SmartKey from the starter
switch.

Connect the positive lead and fasten its
cover
2 (
page 402).

Connect the negative lead.

Reinstall the filter box (
page 401).
Batteries contain materials that can harm
the environment if disposed of improperly.
Large 12-volt storage batteries contain
lead. Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
Warning!
G
Never charge a battery while still installed in
the vehicle unless the accessory battery
charge unit approved by Mercedes-Benz is
being used. Gases may escape during charg-
ing and cause explosions that may result in
paint damage, corrosion or personal injury.
An accessory battery charge unit specially
adapted for Mercedes-Benz vehicles and
tested and approved by Mercedes-Benz is
available, permitting the charging of the bat-
tery in its installed position. Contact an au-
thorized Mercedes-Benz Center for
information and availability. Charge battery
in accordance with the instructions for the
accessory battery charger.
!NEVER invert the terminal connections!!The battery, its filler caps and the vent
tube must always be securely installed
when the vehicle is in operation.
iThe following procedures must be car-
ried out following any interruption of
battery power (e.g. due to reconnec-
tion):

Set the clock (
page 139) (vehi-
cles with COMAND*: see COMAND
operator’s manual).


Resynchronize side windows
(page 240).


Resynchronize panorama roof with
power tilt/sliding panel*
(page 246).

411
Practical hintsFuses
Main fuse box in passenger compartment
1 Main fuse box cover
Opening fuse box
Open the driver’s door

Pull cover 1 open with a screw driver
or similar tool (see arrow).

Remove cover 1 rearward.
Closing fuse box

Attach cover 1 in the front.

Fold cover 1 in until it engages.
Fuse box in engine compartment
The fuse box is located in the engine
compartment on the driver’s side.
1 Cover
2 Screws
3 Retainer
Removing cover
Twist screws 2 90° counterclock-
wise.

Lift the rear of cover 1.

Slide out retainer 3 and remove
cover 1 by pulling towards front. Opening fuse box
4 Fuse box cover
5 Clamps

With a dry cloth, remove any moisture
from the fuse box.

Release clamps 5.

Remove fuse box cover 4.
Closing fuse box

Make sure the sealing rubber is proper-
ly positioned.

Press fuse box cover 4 down and
secure with clamps 5.

412 Practical hintsFusesInstalling cover
Insert cover1 sideways into
retainer 3.

Twist screws 2 90° clockwise.
Fuse box in trunk
The fuse box is located in the trunk behind
the left hand trim panel.
1 Handles
2 Trim panel
Opening
Turn handles 1 clockwise.

Remove trim panel 2. 3
Fuse extractor
4 Fuse box cover
5 Fuse box

Remove fuse box cover 4.
Closing

Insert fuse box cover 4.

Insert trim panel 2.

Turn handles 1 counterclockwise.