2005 MAZDA MODEL 3 5-DOOR length

Black plate (25,1)
qEmergency Locking Mode
In the emergency locking mode, the belt remains comfortable on the occupant and the
retractor will lock in position during a collision. When the seat belt is retracted, it will
always be in the emergency locking mode until it is switched to automatic locking mode by
pulling it all the way out to its full length. If the belt feels tight and hinders comfortable
movement while the vehicle is stopped or in motion, it may be in the automatic locking
mode because the belt has been pulled too far out. To return to the belt more comfortable
emergency locking mode, wait until the vehicle has stopped in a safe, level area, retract the
belt fully to convert it back to emergency locking mode and then extend it around you
again.
qAutomatic Locking Mode
Always use the automatic locking mode to keep the child-restraint system from shifting to
an unsafe position in the event of an accident. To enable seat belt automatic locking mode,
pull it all the way out and connect it as instructed on the child-restraint system. It will
retract down to the child-restraint system and stay locked on it. See the section on child
restraint (page 2-21).
Essential Safety Equipment
Seat Belt Systems
2-11
Mazda3_8T96-EA-04J_Edition3 Page25
Wednesday, May 11 2005 3:36 PM
Form No.8T96-EA-04J

Black plate (32,1)
NOTE
To encourage rear seat passengers to
wear their seat belts, we suggest leaving
the center-rear lap position of the belt
fastened at all times except when
folding the rear seat forward.
qFastening the Lap Portion of the
Seat Belt
Grasp tongue (A) and insert it into the
anchor buckle (B) until you hear a click. It
is now secure for passenger use.
NOTE
After returning the left-rear seatback to
its upright position, fasten the lap
portion of the belt.
Seat Belt Extender
If your seat belt is not long enough, even
when fully extended, a seat belt extender
may be available to you at no charge from
your Authorized Mazda Dealer.
This extender will be only for you and for
the particular vehicle and seat. Even if it
plugs into other seat belts, it may not hold
in the critical moment of a crash.
When ordering an extender, only order
one that provides the necessary additional
length to fasten the seat belt properly.
Please contact your Authorized Mazda
Dealer for more information.
WARNING
Unnecessary Use of an Extender:
Using a seat belt extender when not
necessary is dangerous. The seat belt
will be too long and not fit properly. In
an accident, the seat belt will not
provide adequate protection and you
could be seriously injured. Only use
the extender when it is required to
fasten the seat belt properly.
Using an Improper Extender:
Using a seat belt extender that is for
another person or a different vehicle
or seat is dangerous. The seat belt will
not provide adequate protection and
the user could be seriously injured in
an accident. Only use the extender
provided for you and for the particular
vehicle and seat. NEVER use the
extender in a different vehicle or seat.
2-18
Essential Safety Equipment
Seat Belt Systems
Mazda3_8T96-EA-04J_Edition3 Page32
Wednesday, May 11 2005 3:36 PM
Form No.8T96-EA-04J

Black plate (33,1)
WARNING
Using an Extender That is Too Long:
Using an extender that is too long is
dangerous. The seat belt will not fit
properly. In an accident, the seat belt
will not provide adequate protection
and you could be seriously injured.
Don't use the extender or choose one
shorter in length if the distance
between the extender's buckle and the
center of the user's body is less than
15cm (6 in).
NOTE
When not in use, remove the seat belt
extender and store it in the vehicle. If
the seat belt extender is left connected,
the seat belt extender might get
damaged as it will not retract with the
rest of the seat belt and can easily fall
out of the door when not in use and be
damaged the seat belt warning light will
not illuminate and function properly.
Seat Belt Warning Light/
Beep
The seat belt warning light illuminates
and a beep sound will be heard if the
driver's seat belt is not fastened when the
ignition switch is turned to the ON
position.
Conditions of operation
ConditionResult
The driver's seat belt is not
fastened when the ignition
switch is turned to the ON
position. The warning light
illuminates for about 1
minute and a beep
sound will be heard
for about 6 seconds.
The driver's seat belt is
fastened while the warning
light and the beep sound are
activated. The warning light
turns off and the beep
sound stops.
The driver's seat belt is
fastened before the ignition
switch is turned to the ON
position. The warning light will
not illuminate and the
beep sound will not be
heard.
Essential Safety Equipment
Seat Belt Systems
2-19
Mazda3_8T96-EA-04J_Edition3 Page33
Wednesday, May 11 2005 3:36 PM
Form No.8T96-EA-04J

Black plate (40,1)
3. To get the retractor into the automaticlocking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
4. Push the child-restraint system firmlyinto the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in the
automatic locking mode. If the belt
does not lock the seat down tight,
repeat this step.
NOTE
Inspect this function before each use of
the child-restraint system. You should
not be able to pull the shoulder belt out
of the retractor while the system is in
the automatic locking mode. When you
remove the child-restraint system, be
sure the belt fully retracts to return the
system to emergency locking mode
before occupants use the seat belts.
5. If your child-restraint system requires the use of a tether strap, hook and
tighten the tether strap after raising the
head restraint (except center position)
by following the manufacturer's
instructions.
Anchor bracket location (4 Door)
Anchor bracket
2-26
Essential Safety Equipment
Child Restraint
Mazda3_8T96-EA-04J_Edition3 Page40
Wednesday, May 11 2005 3:36 PM
Form No.8T96-EA-04J

Black plate (44,1)
WARNING
Children and Seating Position with
Side and Curtain Air Bags:
Allowing anyone to lean over or
against the side window, the area of
the front passenger seat, front and
rear window pillars and the roof edge
along both sides from which the side
and curtain air bags deploy, even if a
child-restraint system is used, is
dangerous. If the vehicle is equipped
with side and curtain air bags, the
impact of inflation could cause serious
injury or death to the child.
Furthermore, leaning over or against
the front door could block the side and
curtain air bags and eliminate the
advantages of supplemental
protection. With the front air bag and
the additional side air bag that comes
out of the front seat, the rear seat is
always a better location for children.
Do not allow a child to lean over or
against the side window, even if the
child is seated in a child-restraint
system.
qFront Passenger's Seat Child-
Restraint System Installation
1. Slide the seat as far back as possible.
2. Secure the child-restraint system with
the lap portion of the lap/shoulder belt.
See the manufacturer's instructions on
the child-restraint system for belt
routing instructions.
3. To get the retractor into the automatic locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
4. Push the child-restraint system firmly into the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in automatic
locking mode. If the belt does not lock
the seat down tight, repeat the previous
step and also this one.
2-30
Essential Safety Equipment
Child Restraint
Mazda3_8T96-EA-04J_Edition3 Page44
Wednesday, May 11 2005 3:36 PM
Form No.8T96-EA-04J

Black plate (99,1)
Steering Wheel
WARNING
Adjusting the Steering Wheel:
Adjusting the steering wheel while the
vehicle is moving is dangerous.
Moving it can very easily cause the
driver to abruptly turn to the left or
right. This can lead to loss of control
or an accident. Never adjust the
steering wheel while the vehicle is
moving.
qSteering Wheel Adjustment
To change the angle or length of the
steering wheel:
1. Stop the vehicle, pull down the lock
release lever under the steering
column.
Lock release lever
2. Tilt the steering wheel and/or adjust thesteering column length to the desired
positions, push the lever up to lock the
column.
3. Push the wheel up and down to be certain it's locked before driving.
Mirrors
qOutside Mirrors
Check the mirror angles before driving.
WARNING
Convex Mirror (Passenger Side):
Changing lanes without taking into
account the actual distance of the
vehicle in the convex mirror is
dangerous. You could have a serious
accident. What you see in the convex
mirror is closer than it appears. Be
sure to look over your shoulder before
changing lanes.
Manual control mirror
To adjust, move the mirror's control lever,
just inside the door.
Control lever
Power control mirror
The ignition switch must be in the ACC
or ON position.
Knowing Your Mazda
Steering Wheel and Mirrors
3-29
Mazda3_8T96-EA-04J_Edition3 Page99
Wednesday, May 11 2005 3:37 PM
Form No.8T96-EA-04J

Black plate (327,1)
qCapacities
(Approximate Quantities)
Item Unit
L US qt Imp qt
Engine oil With oil filter replacement 4.3 4.5 3.8
Without oil filter replacement 3.9 4.1 3.4
Coolant With heater 7.5 7.9 6.6
Without heater 6.9 7.3 6.1
Manual transaxle oil 2.87 3.03 2.53
Automatic transaxle fluid 7.2 7.6 6.3
Fuel tank 5514.5
(US gal) 12.1
(Imp gal)
Check oil and fluid levels with dipsticks or reservoir gauges.
q Dimensions
Item Model
4 Door 5 Door
Overall length (STD) 4,530 mm (178.3 in)
―
(SAP) 4,540 mm (178.7 in) 4,485 mm (176.6 in)
Overall width
*1,755 mm (69.1 in) 1,755 mm (69.1 in)
Overall height 1,465 mm (57.7 in)1,465 mm (57.7 in)
Front tread 1,530 mm (60.2 in)1,530 mm (60.2 in)
Rear tread 1,515 mm (59.6 in)1,515 mm (59.6 in)
Wheelbase 2,640 mm (103.9 in)2,640 mm (103.9 in)
* With side protector
q Weights
4 Door
2.0-liter engine
Item Weight
Manual transaxle Automatic transaxle
GVWR (Gross Vehicle Weight Rating) 1,702 kg (3,752 lb),
1,708 kg (3,765 lb)
*11,721 kg (3,794 lb),
1,727 kg (3,807 lb)*1
GAWR (Gross Axle Weight Rating) Front 904 kg (1,993 lb) 924 kg (2,037 lb)
Rear
798 kg (1,759 lb),
804 kg (1,772 lb)*1797 kg (1,757 lb),
803 kg (1,770 lb)*1
*1 P-ZEV
Specifications
10-5
Mazda3_8T96-EA-04J_Edition3 Page327
Wednesday, May 11 2005 3:40 PM
Form No.8T96-EA-04J

Contents,\bAccessor\fes\a,\band\bLaser\b\b\b\b
Before U\be
Accessor\fes
Please\bcontact\ban\bAutho\ar\fzed\bMazda\bDealer\b\ff\by\aou\bare\bm\fss\fng\bany\bof\bthe\bfol\alow\fng\baccessor\fes.
Map\bD\fsc
Owner's\bManual
CAUT\fON:
TH\fS PRODUCT \fS A CLAS\OS LASER PRODUCT \O.I
HOWEVER TH\fS PRODUCT\O USES A V\fS\fBLE/\fNV\fS\O\fBLE LASER BEAM
WH\fCH COULD CAUSE HAZA\ORDOUS RAD\fAT\fON EXPOSU\ORE \fF D\fRECTED.
BE SURE TO OPERATE T\OH\fS PRODUCT CORRECTLY\O AS \fNSTRUCTED.
USE OF CONTROLS OR AD\OJUSTMENTS OR PERFORM\OANCE OF
PROCEDURES OTHER THA\ON THOSE SPEC\fF\fED HE\ORE\fN MAY RESULT \fN
HAZARDOUS RAD\fAT\fON EX\OPOSURE. DO NOT OPEN \OCOVERS AND DO
NOT REPA\fR YOURSELF.\O REFER SERV\fC\fNG TO QU\OAL\fF\fED PERSONNEL.
2
La\ber product\b:
Wave\blength:\b650\bnm
Laser\bpower:\bNo\bhazardo\aus\brad\fat\fon\b\fs\bem\ftted\a\bw\fth\bsafety\bprotect\fo\an.
Prepa-
ration
\fmme-
diate
use
Advanced
use
\ff
necessary
Marked\bPo\fnt
Direct De
After Rou
Route Ch
\b\b\bProd
Setup
Precaut\fons/S
Troubleshoot
Ma\fntenance
De\btin
Charac
PO\f \fco
Accessor\fes\bLaser\bProduc
Contents\b.\b.\b.\bSafety\bInform
Introduct\fon\bNames\band\bF
Before U