2005 LEXUS LS430 remote control

KEYS AND DOORS
51
The flashing indicator light will stay on when all the doors, trunk
and hood are closed and locked.
3. After 30 seconds, the indicator starts flashing and the
system is set.
After the system is set, when you close the trunk which is
opened
with an ignition key or wireless remote control or smart
key system, the system is set again. However, this function
operates only when the door is not unlocked during which the
trunk is opened and closed.
In case of the ignition switch with the key inserted:
1. Turn the ignition key to the “LOCK” position and
remove it.
The engine immobilizer system causes the indicator light to
flash.
2. Close and lock all the doors, trunk and hood using an
ignition key or wireless remote control or smart key
system.
If you lock them with wireless remote control or smart key
system, the turn signals flash once.*
NOTE:
* The turn signals can be set not to flash.
Ask your Lexus dealer for details.
The flashing indicator light will stay on when all the doors, trunk
and hood are closed and locked. 3. After 30 seconds, the indicator starts flashing and the
system is set.
After the system is set, when you close the trunk which is
opened
with an ignition key or wireless remote control or smart
key system, the system is set again. However, this function
operates only when the door is not unlocked during which the
trunk is opened and closed.
Cancelling the system
When you unlock any door using an ignition key , wireless
remote control or smart key system, the system is
cancelled.
If you unlock any door with the wireless remote control or smart
key system, the turn signals flash twice.*
NOTE:
* The turn signals can be set not to flash.
Ask your Lexus dealer for details.

KEYS AND DOORS
52
Activating the system
The alarm sounds for 60 seconds if any of the following are
operated:
Unlocking any door or trunk without using an ignition key,
wireless remote control or smart key system.
 Opening the hood forcibly.
 Reconnecting the battery.
 Hot− wiring the ignition.
If any door is unlocked and the ignition key is not in the ignition
switch during the alarm sounding, its door is automatically
locked.
To stop the alarm: Use either of the following methods.
 Unlock the door or trunk using an ignition key or wireless
remote control or smart key system.
 Turn the ignition switch on.
Testing the system
1. Open all the windows.
2. Set the system as described above.
The doors should be locked with an ignition key, wireless
remote control or smart key system. Be sure to wait until the
indicator light starts flashing.
3. Unlock one of the doors from the inside through one of
the opened windows.
The system should activate the alarm.
4. Unlock any of the doors with an ignition key, wireless
remote control or smart key system to cancel the system.
5. Repeat this operation for the other doors, trunk and
hood.
When testing the hood, also check that the system is activated
when the battery terminal is disconnected and then
reconnected.
If the system does not work properly, have it checked by your
Lexus dealer.
NOTICE
When disconnecting the battery, be sure to cancel the
theft deterrent system. Otherwise, the system could
activate an alarm and lock the unlocked door(s)
automatically.

SWITCHES
55
12L054b
The automatic light control sensor is on the top center of the
instrument panel.
Do not place anything on the instrument panel, and/or do not
affix anything on the windshield to block this sensor.
When you turn on the headlights, the lights automatically turn
off about 30 seconds after any of the doors is opened and
closed with the ignition switch turned to the “ACC” or “LOCK”\
position.* To turn them on again, turn the ignition switch to the
“ON” position, or turn the headlight switch off and then twist the
knob until the first or second clickstop. If you are going to park
for over one week, make sure the headlight switch is off.
When the headlight switch is on with all the doors locked and
the trunk closed, pushing the “LOCK” button on the wireless
remote control key turns off the headlights.
NOTE:
* The time before turning off the lights can be changed.
Ask your Lexus dealer for details. Daytime Running Light System
The headlights turn on at reduced intensity when the parking
brake is released with the engine started, even with the light
switch in the “OFF” position. They will not go off until the
ignition switch is turned off.
To turn on the other exterior lights and instrument panel lights,
twist the knob to the first clickstop.
Twist
the knob to the second clickstop to turn on the headlights
to full intensity for driving at night.
When setting the knob to the third clickstop (“AUTO”), the
headlights will automatic ally adjust to full intensity and/or turn
on the other lights depending on the darkness of the
surroundings. Likewise, as the surroundings become brighter,
the headlights will turn to reduced intensity, ultimately turning
off the other lights.
NOTICE
To prevent the battery from being discharged, do not
leave the lights on longer than necessary when the
engine is not running.

SWITCHES
65
12L249
Operating the switches
To lower the window, push the switch halfway down. Pull
it up to raise the window. The window glass moves as long
as the switch is operated.
Automatic operation: To fully raise or lower the window
automatically, pull the switch fully up or push it fully down.
To stop the window partway, lightly push or pull the switch in
the opposite direction and then release it.
Operating the window lock switch
12L250
 Indicator light
With the window lock switch pressed in, only the driver’s
window can be raised or lowered.
The indicator lights on the swit ches tell you which of the
switches can be operated.
Even with the window lock switch pressed in, the windows will
be opened from outside the vehicle using an ignition key or
wireless remote control.

SWITCHES
66
Operating the windows from outside the
vehicle
The windows can be operated using the key.*NOTE:
* This feature can be deactivated.
Ask your Lexus dealer for details.
12L180
Type A
12L177
Type B
Insert the key into the keyhole on the driver’s door.
To close the windows: Turn the key in the locking direction
and hold it.
After the door is locked, the windows begin to close. To stop
in the middle, return the key.
To open the windows: Turn the key in the unlocking direction
and hold it.
After the door is unlocked, the windows begin to open. To stop
in the middle, return the key.
This function will work even with the window lock switch
pressed in.
The windows also can be opened using the wireless remote
control. For details, see page 40.

EXTERIOR EQUIPMENT
143
TRUNK LID
15L096a
 1Type A 2Type B
To unlock the trunk lid, insert the master key and turn it
clockwise.
To close the trunk lid, lower it and press down on it. After
closing the trunk lid, try pulling it up to make sure it is securely
closed.
The trunk lid can be unlocked by pushing the trunk button or
using the wireless remote control function. For details, see
“Smart key system” on page 20 and “Wireless remote control”
on page 36.
When you open the trunk, the lights illuminate the inside of the
trunk and around your feet.
CAUTION
 Keep the trunk lid closed while driving. This not only
prevents luggage from being thrown out, but also
prevents exhaust gases from entering the vehicle.
 Always lock the trunk lid and all doors, and keep the
vehicle keys out of children’s reach .
 Never leave children unattended in the vehicle.
Unsupervised children may lock themselves in the
vehicle or trunk and suffer serious injuries or death.

OCCUPANT RESTRAINT SYSTEMS
223
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the smart key in which you want to cancel the
registration in possession and push the “SET” button.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with the “SET” button held
down.
When the previous key ID memory is erased, two beeps
sound.MEMORY CALL SYSTEM USING A WIRELESS REMOTE
CONTROL KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized
position when you open the driver’s door after
unlocking it with a wireless remote control key. And when
you insert the key into the ignition switch, the tilt and
telescopic steering is adjusted.
To activate this system, the ID of the wireless remote
control key ne eds to be registered in the memory button.
Registering the wireless remote control key
ID code
Before the registration of the ID of the wireless remote control
key, the driving position must be memorized in the memory
button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the wireless remote control key in possession,
select a button in which you want to record the ID of the
key from buttons “1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with button “1”,
“2” or “3” held down.

OCCUPANT RESTRAINT SYSTEMS
224When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered
in another button, that memory will also be erased.
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the wireless remote control key in which you want
to cancel the registrati on in possession and push the
“SET” button.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with the “SET”
button held down.
When the previous key ID memory is erased, two beeps
sound.
REAR SEAT POSITION MEMORY SYSTEM
A microcomputer will memorize the position of the rear seats
and the height of the rear head restraints.
Recording the rear seat position in the computer’s memory can
only be done when the ignition switch is in the “ON” position.
Setting the rear seat position
16L301a
1. Adjust the rear seat position and the height of the head
restraint of the rear seat to the desired position.
2. Keep pushing the “SET” button until a beep sounds.
The beep sound means that the position has been memorized.
The memory will be erased when the battery is removed for
inspection or service.