2005 LEXUS LS430 change time

GAUGES, METERS AND SERVICE REMINDER INDICATORS
90
MULTIINFORMATION DISPLAY
13L146
The multiinformation display provides various
information, including your vehicle’s driving condition,
outside temperature, and warning messages if your
vehicle is in trouble.
During ordinary driving, cruise information and graphic
information are displayed. However, if any problem
occurs in your vehicle, a warning message appears above
the cruise information.
(a) Cruise information
13L197
 1 “DISP1” button 2“DISP2” button
3“RESET” button
The following information is shown with the ignition
switch turned on. Each time you push the “DISP1” button,
the displayed information is changed.
 Available driving distance
 Average fuel consumption
 Current fuel consumption
 Average fuel consumption after being refueled
 Driving distance after being refueled
 Elapsed time
 Average vehicle speed
 Blank

GAUGES, METERS AND SERVICE REMINDER INDICATORS
93
(b) Graphic information
13L147
The following graphic information is shown on the
display.
Any door open
 Compass display (if equipped)
 Outside temperature display
 Lexus park assist system display (if equipped)
 Dynamic radar/laser cruise control display (if equipped)
 Blank
If any door is opened, the warning message also reminds you
to close the door. When the ignition is turned on, the previously selected display
appears. Each time you push the “DISP2” button for about 1
to 2 seconds, the display changes from compass (if the
compass is
initially displayed) to outside temperature to blank
screen, then back to compass.
For the compass, see “Compass” on page 105. For the outside
temperature display, see “Outside temperature display” on
page 117.
If you push the main switch of the Lexus park assist system or
turn the ignition on with the main switch of the Lexus park assist
system on, the Lexus park assist system screen appears for
2 seconds and then the multi −information display returns to the
previous screen.
When you push the main switch of the dynamic radar/laser
cruise control, the dynamic radar/laser cruise control screen
appears. Each time you push the “DISP2” switch for 1 to 2
seconds, the screen changes to compass, outside
temperature display, blank screen, and then back to the
dynamic radar/laser cruise control screen. When the display
shows a screen other than dynamic radar/laser cruise control,
the multi −information display returns to the dynamic
radar/laser cruise control screen after 6 seconds. For details,
see “Dynamic radar/laser cruise control” on page 329.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
103
w280
If the system cannot easily measure the
vehicletovehicle distance because of the following
conditions while the dynamic radar/laser cruise control is
on, the master warning light comes on, the “CRUISE”
indicator light flashes, and a warning tone sounds. At this
time the above message appears.
Dynamic radar cruise control—
 The driving pattern selector switch is set to the “SNOW”
mode.
 It is determined that it is difficult to make a measurement
because of bad weather (such as extremely hot weather)
 The wipers are operated at high speed with the wiper lever
in the “AUTO” position
Dynamic laser cruise control—
 The driving pattern selector switch is set to the “SNOW”
mode.
 It is determined that it is difficult to make a measurement
because of bad weather (such as rainy, foggy, or snowy
weather)
 The wipers are operated at high or low speeds with the
wiper lever in the “AUTO” position.
 Direct sunlight from the front In the following
cases, the dynamic radar/laser cruise
control switches to the “RADAR READY” mode:
Dynamic radar cruise control—
 The driving pattern selector switch is changed to the
“normal” or “power” position.
 The wipers are stopped or are switched to low speed or
intermittent operation. (Including intermittent and stopped
wipers in the “AUTO” position)
In the above conditions, press the control lever upward in the
“RES/ACC” direction and release it. The dynamic radar cruise
control will be restored, however, even after the weather
clears, if the setting operation cannot be performed or if the
warning message still appears, the system might have
malfunctioned. Although it is no problem to continue driving,
contact your Lexus dealer.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
104Dynamic laser cruise control—

The driving pattern selector switch is changed to the
“normal” or “power” position.
 The wipers are stopped or are switched to intermittent
operation. (Including intermittent and stopped wipers in the
“AUTO” position)
 No direct sunlight from the front
In the above conditions, press the control lever upward in the
“RES/ACC” direction and release it. The dynamic laser cruise
control will be restored, however, even after the weather
clears, if the setting operation cannot be performed or if the
warning message still appears, the system might have
malfunctioned. Although it is no problem to continue driving,
contact your Lexus dealer.
w281
If a system malfunction is detected when dynamic
radar/laser cruise control is in the “RADAR READY” mode
or operating, the master warning light comes on, the
“CRUISE” indicator light flashes and a warning tone
sounds. At this time the above message appears.
If this message appears, stop your vehicle in a safe place, turn
the ignition off, and then restart it to reset the system. If the
setting still cannot be made or the same message appears
again, the system might have malfunctioned. Although it is no
problem to continue driving, contact your Lexus dealer.
NOTICE
While you are cruising with the dynamic radar/laser
cruise control on, if the master warning light comes on,
the cruise indicator light flashes, “Check Cruise
System” appears on the multiinformation display and
the warning tone sounds, turn the ignition switch off
and then on again. If the function is cancelled again
after setting or if settings cannot be made, the dynamic
radar/laser cruise control system may be
malfunctioning. Although it is no problem to continue
driving, have your vehicle checked by your Lexus
dealer.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
105
w278
The master warning light comes on, a warning tone
sounds and the above message appears in the following
conditions:
The millimeter wave radar sensor or the grille cover is
dirty.
Clean the grille or sensor with a soft cloth to remove the dirt.
 The precollision seat belts are activated repeatedly for
a short time.
The system turns of f temporarily for overheating protection,
but turns back on after a while.
w277
If there is a problem somewhere in the precollision safety
system, the master warning light comes on, a warning
tone sounds, and the above message appears.
If the above message appears, the pre −collision safety system
may not operate. Contact your Lexus dealer as soon as
possible to service the vehicle.
COMPASS
(Vehicles without Navigation System)
13L149
When the ignition is turned on, the previously selected display
appears. If the compass is not displayed, push the “DISP2”
button several times for 1 to 2 seconds to display the compass.
However if you push the main switch of dynamic radar/laser
cruise control to use dynamic radar/laser cruise control, the
dynamic radar/laser cruise control display appears. To change
to the compass display, push the “DISP2” button for longer
than about 1 second.
The compass indicates the direction in which the vehicle
is heading. The illustration shown above indicates that the
vehicle is heading north.

INTERIOR EQUIPMENT
11 6
FOOT LIGHTS
14L327
 1Front foot light 2Rear foot light
The foot lights come on and go out in the following conditions.
 The lights come on for about 15 seconds when any of the
doors are opened.* However, when all the doors are closed
and locked, the lights go out immediately.
 The lights come on when the ignition switch is turned to
“ON” from “ACC” with the selector lever in the “P” position.
When you move the lever out of “P” position, the intensity
of the lights are reduced.
Turning the instrument panel light control counterclockwise
fully turns off the foot lights. NOTE:
*The illumination time of the foot lights can be changed.
Ask your Lexus dealer for details.
CLOCK
14L225
Vehicles with navigation system
For clock setting, see the separate “Navigation System
Owner’s Manual”.

INTERIOR EQUIPMENT
11 7
14L060
Vehicles without navigation system
The digital clock indicates the time with the ignition switch
at the “ACC” or “ON” position. To reset the hour, press the
“H” button. To reset the minutes, press the “M” button.
To adjust the time to the nearest hour, press the “:00”
button.
For example, if the “:00” button is pressed when the time is
between 9:30 − 9:59 or between 10:01 − 10:29, the time will
change to 10:00.
If the electrical power source has been disconnected from the
clock, the time display will automatically be set to 1:00.
OUTSIDE TEMPERATURE DISPLAY
14L226
 On the instrument panel (Vehicles with navigation
system)

INTERIOR EQUIPMENT
123
The battery side of the hand
−held transmitter must be pointed
away from the HomeLink
\b during the programming process.
For Canadian users, follow the procedure in “Programming an
entrance gate/Programming all devices in the Canadian
market”.
1. Decide which of 3 HomeLink
\b buttons you want to program.
2. Place your hand− held garage transmitter 25 to 75 mm (1 to
3 in.) away from the surface of the HomeLink
\b.
Keep the indicator light on the HomeLink
\b in view while
programming.
3. Simultaneously press and hold the hand −held garage
transmitter button along with the selected HomeLink
\b button.
4. When the indicator light on the HomeLink
\b changes from a
slow to a rapid flash after 20 seconds, you can release both
buttons.
5. Test the operation of the HomeLink
\b by pressing the newly
programmed button. If programming a garage door opener,
check to see if the garage door opens and closes.
If the garage door does not operate, identify if your garage
transmitter is of the “Rolling Code” type. Press and hold the
programmed HomeLink
\b button. The garage door has the
rolling code feature if the indicator light (on the HomeLink\b)
flashes rapidly and then remains lit after 2 seconds. If your
garage transmitter is the “Rolling Code” type, proceed to the
heading “Programming a rolling code system”. 6. Repeat steps 2 through 5 for each remaining HomeLink
\b
button to program another device.
Programming a rolling code system
If your device is “Rolling Code” equipped, it is necessary
to follow steps 1 through 4 under the heading
“Programming the HomeLink
\b” before proceeding with
the steps listed below.
1. Locate the “training” button on the ceiling mounted garage
door opener motor. The exact location and color of the button
may vary by brand of garage door opener. Refer to the owner’s
guide supplied by the garage door opener manufacturer for the
location of this “training” button.
2. Press the “training” button on the ceiling mounted garage
door opener motor.
Following this step, you have 30 seconds in which to initiate
step 3 below.
3. Press and release the vehicle’s programmed HomeLink
\b
button twice. The garage door may open. If the door does
open, the programming process is complete. If the door does
not open, press and release the button a third time. This third
press and release will complete the programming process by
opening the garage door.
The ceiling mounted garage door opener motor should now
recognize the HomeLink
\b unit and be able to activate the
garage door up/down.