2005 KIA Rio light

4-33 Door Ajar Warning
This warning light comes on when a door is not closed
securely with the ignition switch in any position.Anti-Lock Brake System (ABS)
Warning Light (if equipped)This light illuminates when you start the engine. The
light will go off if the ABS system is operating nor-
mally. Also, this light comes on if the key is turned to
ON, and then goes off in 2-3 seconds if the system is
operating normally.
If this warning light illuminates while the vehicle is
being driven, have the vehicle checked by an autho-
rized Kia Dealer as soon as possible.Rear Window Defroster Indicator This light comes on when the rear defroster is ON.Rear Hatch Warning Light
(5 door-if equipped)This warning light comes on when a rear hatch is not
closed securely with the ignition switch in any posi-
tion.
AS2B04020
LightingLighting ControlTo turn the lights on, twist the knob on the end of the
control lever which is located on the steering column
to the left of the steering wheel.
First position
Tail, parking, license and sidemarker lights and instru-
ment panel lights ON.
Second position
Head, tail, parking, license and sidemarker lights and
instrument panel lights ON.
ABS
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 33

Driving Your Vehicle4-34 High-Beam OperationFor high beam headlights, push the lever away from
you. Pull it back for low beams.
The high-beam indicator will illuminate when the
headlight high beams are switched ON.
To prevent the battery from being discharged, do not
leave the lights ON for a prolonged time while the
engine is not running.
Flashing HeadlightsTo flash the headlights, pull the lever toward you. It
will return to the normal position when released. The
headlight switch does not need to be ON to use this
flashing feature.
AS2B04021
AS2B04022
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 34

4-35 Turn Signals
The same lever that controls the headlights also con-
trols the turn signals.
The ignition switch must be ON for the turn signals
to function. Move the lever up or down to activate the
turn signals. The turn signals will self-cancel after a
turn is completed. If the indicator continues to flash
after a turn, manually return the lever to the OFF (mid-
dle) position.
Lane Change Signals
To signal a lane change, move the turn signal lever
slightly and hold it in position. The lever will return to
the OFF (middle) position when released.
Green arrow indicators on the instrument panel indi-
cate which turn signal is operating. If an indicator
stays ON and does not flash or if it flashes abnormally,
one or more of the turn signal bulbs may be burned out
and will require replacement.Daytime Running Lights (DRL)Daytime Running Lights (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving condi-
tions, but they can be especially helpful in the short
periods after dawn and before sunset. The DRL system
will make your low-beam headlights turn OFF when:
 The headlight switch is ON.
 The parking brake is engaged.
 The engine stops.
AS2B04023
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 35

Hazard Warning Flasher
The hazard warning flasher causes the rear tail
lights and front turn signal lights to flash on and
off, which serves as a warning to other drivers to
exercise caution when approaching or passing
your vehicle.
To activate the flasher, depress the hazard warning
flasher switch. This switch operates in any igni-
tion switch position.
To turn the flashers off, depress the switch again.
4-39 Type B
The defroster heats the window to remove frost, fog
and thin ice from the interior and exterior of the rear
window. The ignition switch must be ON for the
defroster to operate.
To activate the rear window defroster, press the rear
window defroster button located in the center console
switch panel. The instrument panel rear window
defroster indicator illuminates when the defroster is ON.
The rear window defroster automatically turns OFF
after 20 minutes or when the ignition switch is turned
OFF. To turn off the defroster, press the rear window
defroster button again. If there is heavy accumulation
of snow on the rear window, brush it off before operat-
ing the rear defroster.
✽
NOTICE
To prevent damage to the conductors bonded to
the inside surface of the rear window, never use
sharp instruments or window cleaners containing
abrasives to clean the window.✽
NOTICE
To prevent the battery from being discharged,
operate the defroster only while the engine is run-
ning.
1B3104014B
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 39

4-41 Cigarette Lighter
To operate the cigarette lighter, press it in and release
it. When it is heated, it automatically pops out ready
for use. If the engine is not running, the ignition switch
must be in the ACC position for the lighter to operate.
1S2107021
✽
NOTICE
 Do not hold the lighter in because it will over-
heat.
 Only a genuine Kia lighter should be used in
the cigarette lighter socket. The use of plug-in
accessories (shavers, hand-held vacuums and
coffee pots, for example) may damage the
socket or cause electrical failure.
 If the lighter does not pop out within
30 seconds, remove it to prevent overheating.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 41

Outside (fresh) air position
If you press the air intake control button again, the air
position will be changed to outside (fresh) air and air
will enter the ventilation system from outside the vehi-
cle. Use this position for normal ventilation and heat-
ing.
The air flow control will be set at outside (fresh) air
position automatically if any of following occur.
- The ignition key is OFF.
- The fan speed control knob is OFF (0).
- When you select the floor-defrost or defrost mode
position.
If you want the recirculated air position, press the cor-
responding button.
To cancel the forced outside (fresh) air position, refer
to the canceling procedure in “Windshield Defrosting
and Defogging” section.
Air Conditioning Switch (If Equipped)
Depress the switch to turn the air conditioning system
on. An indicator light in the switch will illuminate
when the fan switch is ON indicating air conditioning
system operation. Depress the switch again to turn the
air conditioning system OFF.
4-47
1B3104017C
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 47

4-49
Air Conditioning (If Equipped)
All Kia Air Conditioning Systems are filled with envi-
ronmentally friendly R134a refrigerant which is not
damaging to the ozone layer.
1. Start the engine. Depress the air conditioning
switch.
2. Set the mode selection knob to the face posi-
tion.
3. Set the air intake control switch to the outside air or
the recirculated air position (switch indicator ON).
4. Set the temperature control knob to the desired
position.
5. Set the fan speed control knob to the desired speed.
6. Adjust the fan speed control knob and temperature
control knob to maintain maximum comfort.
If warmer air is desired at floor level for bi-level
operation, set the mode selection knob to the
position and adjust the temperature control knob to
maintain maximum comfort.
When maximum cooling is desired, set the tempera-
ture control knob to the extreme left position and set
the air intake control switch to the recirculated air
position, then set the fan speed control knob to the
highest speed.
Air Conditioning System Operating Tips:
 If the vehicle has been parked in direct sunlight dur-
ing hot weather, open the windows for a short time
to let hot air inside the vehicle escape.
 To help reduce moisture on the inside of windows
on rainy, humid days, decrease the humidity inside
the vehicle by operating the air conditioning system.
 During air conditioning system operation, you may
occasionally notice a slight change in engine speed
at idle as the A/C compressor cycles ON. This is a
normal system operating characteristic.
 Use the air conditioning system every month if only
for a few minutes.
✽
NOTICE
When using the air conditioning system, monitor
the temperature gauge closely while driving up
long hills or in heavy traffic when outside temper-
atures are high. Air conditioning system operation
may cause engine overheating. Continue to use
the blower fan but turn the air conditioning sys-
tem off if the temperature gauge indicates engine
overheating.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 49

If you don’t want the outside (fresh) air position when
operating in either of these modes, you can turn off the
system operation by performing the following:
1. Make sure the engine is running or the ignition
switch is in the ON position.
2. Turn the fan speed control knob to the “0” position.
3. Turn the mode selection knob to the defrost ( )
position.
4. Push the air intake control button ( ) at least 5
times within 3 seconds.
5. Then the indicator light on the air intake control but-
ton ( ) will blink 3 times with 0.5 second intervals
between blinks.
If you want to return to the automatic outside (fresh)
air position, repeat the procedure above.
4-53
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 53