2005 JAGUAR S TYPE fuse
[x] Cancel search: fusePage 84 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationDYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
FUEL / TRUNK RELEASE SWITCH PACK FC43 10-WAY / GREY INSTRUMENT PANEL
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
SPEED CONTROL MODULE FC6 30-WAY / YELLOW INSTRUMENT PANEL, DRIVER SIDE
SPEED CONTROL SENSOR CC1 5-WAY / BLACK BELOW LH FRONT BUMPER
STEERING WHEEL — — STEERING WHEEL
TRANSMISSION CONTROL MODULE GB2 16-WAY / BLACK TRANSMISSION CONTROL VALVE ASSEMBLYHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC19 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
FH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH90 6-WAY / GREY / SPEED SENSOR LINK HARNESS TO FRONT HARNESS BELOW LH FRONT HEADLAMP ASSEMBLY
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Speed Control Module Pin Description and CharacteristicO FC6–5 FORWARD ALERT SWITCH / INDICATOR DRIVE: FORWARD ALERT INDICATOR DRIVE
O FC6–6 CHIME MODULE DRIVE: CHIME ACTIVATE
C FC6–8 CAN –
C FC6–9 CAN +
PG FC6–12 POWER GROUND: GROUND
B+ FC6–14 IGNITION SWITCHED POWER SUPPLY: B+
B+ FC6–15 SWITCHED SYSTEM POWER SUPPLY: B+
I FC6–20 FORWARD ALERT SWITCH / INDICATOR DRIVE: MONITOR FORWARD ALERT SWITCH
C FC6–23 CAN –
C FC6–24 CAN +Dynamic Stability Control ModulePin Description and CharacteristicC FH103–11 CAN +
C FH103–12 CAN +
C FH103–14 CAN –
C FH103–15 CAN –Engine Control ModulePin Description and CharacteristicSS PI1–47 SPEED CONTROL SWITCH REQUEST: STEPPED RESISTANCE
I PI1–48 SPEED CONTROL SWITCHES SIGNAL GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +Instrument ClusterPin Description and CharacteristicC FC9–12 CAN +
C FC9–13 CAN –
C FC9–28 CAN +
C FC9–29 CAN –
Page 86 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.4
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationADAPTIVE DAMPING CONTROL MODULE CA11 16-WAY / BLUE LUGGAGE COMPARTMENT, REAR
CA12 16-WAY / GREY
DAMPER SOLENOID – LH FRONT FH117 2-WAY BLACK TOP OF LH FRONT DAMPER
DAMPER SOLENOID – LH REAR CA140 2-WAY BLACK TOP OF LH REAR DAMPER
DAMPER SOLENOID – RH FRONT FH118 2-WAY BLACK TOP OF RH FRONT DAMPER
DAMPER SOLENOID – RH REAR CA111 2-WAY BLACK TOP OF RH REAR DAMPER
DYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
LATERAL ACCELEROMETER FH70 3-WAY / BLACK REARWARD OF FRONT BUMPER, LH SIDE
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
VERTICAL ACCELEROMETER – FRONT FH63 3-WAY / BLACK REARWARD OF FRONT BUMPER, LH SIDE
VERTICAL ACCELEROMETER – REAR CA17 3-WAY / BLACK LUGGAGE COMPARTMENT, RH REARHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEMGROUNDS
Ground LocationCA158 LUGGAGE COMPARTMENT, LH SIDE REAR CORNER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Adaptive Damping Control Module Pin Description and CharacteristicO CA11–1 RH REAR DAMPER SOLENOID DRIVE: PWM +
O CA11–2 RH REAR DAMPER SOLENOID DRIVE: PWM –
O CA11–3 LH REAR DAMPER SOLENOID DRIVE: PWM +
O CA11–4 LH REAR DAMPER SOLENOID DRIVE: PWM –
O CA11–5 LH FRONT DAMPER SOLENOID DRIVE: PWM –
O CA11–6 LH FRONT DAMPER SOLENOID DRIVE: PWM +
O CA11–7 RH FRONT DAMPER SOLENOID DRIVE: PWM –
O CA11–8 RH FRONT DAMPER SOLENOID DRIVE: PWM +
SG CA11–9 SIGNAL GROUND (INTERNALLY CONNECTED TO PIN 10): GROUND
PG CA11–10 POWER GROUND: GROUND
B+ CA11–12 IGNITION SWITCHED POWER SUPPLY (II): B+
S CA11–13 SCP –
S CA11–14 SCP +
B+ CA11–16 BATTERY POWER SUPPLY: B+
SS CA12–9 SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I CA12–10 REAR VERTICAL ACCELEROMETER SIGNAL: SENSOR SIGNAL
I CA12–11 LATERAL ACCELEROMETER SIGNAL: SENSOR SIGNAL
I CA12–12 FRONT VERTICAL ACCELEROMETER SIGNAL: SENSOR SIGNALDynamic Stability Control ModulePin Description and CharacteristicC FH103–11 CAN +
C FH103–12 CAN +
C FH103–14 CAN –
C FH103–15 CAN –Instrument ClusterPin Description and CharacteristicC FC9–12 CAN +
C FC9–13 CAN –
S FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –Rear Electronic ModulePin Description and CharacteristicS CA102–1 SCP +
S CA102–2 SCP –
Page 88 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.5
NOTE: FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationFRONT LH TIRE PRESSURE SENSOR FRONT LH WHEEL
FRONT LH TPMS INITIATOR FH5 2-WAY / GREY FRONT LH WHEEL ARCH
FRONT RH TIRE PRESSURE SENSOR FRONT RH WHEEL
FRONT RH TPMS INITIATOR FH26 2-WAY / GREY FRONT RH WHEEL ARCH
REAR LH TIRE PRESSURE SENSOR REAR LH WHEEL
REAR LH TPMS INITIATOR RL4 2-WAY / GREY REAR LH WHEEL ARCH
REAR RH TIRE PRESSURE SENSOR REAR RH WHEEL
REAR RH TPMS INITIATOR RR4 2-WAY / GREY REAR RH WHEEL ARCH
SPARE TIRE PRESSURE SENSOR SPARE WHEEL
TIRE PRESSURE MONITORING SYSTEM MODULE CA146 16-WAY / BLUE LUGGAGE COMPARTMENT, RH REAR CA147 16-WAY / GREY
TIRE PRESSURE RECEIVER MODULE RF15 3-WAY / BLACK BELOW CENTER CONSOLEHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS ADJACENT TO FRONT RH WHEEL ARCH
FH3 2-WAY GREY / LINK HARNESS ADJACENT TO FRONT LH WHEEL ARCH
RF34 16-WAY GREEN / ROOF HARNESS HEADLINER, CLOSE TO ROOF CONSOLE
RL2 8-WAY BLACK / LINK HARNESS ADJACENT TO REAR LH WHEEL ARCH
RR2 6-WAY GREY / LINK HARNESS ADJACENT TO REAR RH WHEEL ARCHGROUNDS
Ground LocationCA116 BEHIND REAR SEAT BACK, RH SIDE
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Tire Pressure Monitoring System Module
Pin Description and CharacteristicO CA146–5 REAR LH TPMS INITIATOR: RF 125kHz +
O CA146–6 REAR LH TPMS INITIATOR: RF 125kHz –
O CA146–7 REAR RH TPMS INITIATOR: RF 125kHz +
O CA146–8 REAR RH TPMS INITIATOR: RF 125kHz –
O CA146–13 FRONT LH TPMS INITIATOR: RF 125kHz +
O CA146–14 FRONT LH TPMS INITIATOR: RF 125kHz –
O CA146–15 FRONT RH TPMS INITIATOR: RF 125kHz +
O CA146–16 FRONT RH TPMS INITIATOR: RF 125kHz –
I CA147–4 TIRE PR ESSURE DATA:
B+ CA147–8 IGNITION SWITCHED POWER SUPPLY (II): B+
C CA147–10 CAN –
C CA147–11 CAN +
PG CA147–12 POWER GROUND: GROUND
B+ CA147–16 BATTERY POWER SUPPLY: B+Tire Pressure Receiver Module
Pin Description and CharacteristicO RF15–1 OUTPUT SIGNAL TO TPMS MODULE
PG RF15–2 POWER GROUND: GROUND
B+ RF15–3 BATTERY POWER SUPPLY: B+
Page 90 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 06.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CONDITIONING CONTROL MODULE – PANEL FC27 26-WAY / GREY CENTER CONSOLE
FC28 22-WAY / GREY
AIR CONDITIONING CONTROL MODULE – REMOTE FC40 26-WAY / GREY BEHIND INSTRUMENT PANEL, RH SIDE (LHD), LH SIDE (RHD) FC41 22-WAY / GREY
AMBIENT TEMPERATURE SENSOR FH30 2-WAY / BLACK UNDER FRONT BUMPER, CENTER, FORWARD OF RADIATOR
AUXILIARY COOLANT PUMP (DIESEL) CP6 2-WAY / BLACK ENGINE COMPARTMENT, BEHIND RADIATOR, LH SIDE
AUXILIARY COOLANT PUMP (GASOLINE) CP4 2-WAY / BLACK ENGINE COMPARTMENT, BEHIND RADIATOR, LH SIDE
AUXILIARY COOLANT PUMP RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R7
BLOWER MOTOR AC2 6-WAY / BLACK UNDER INSTRUMENT PANEL, RH SIDE (LHD), LH SIDE (RHD)
BLOWER MOTOR RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R7
DEFROST MODE ACTUATOR FC29 6-WAY / BLACK AIR DISTRIBUTION BOX
DISCHARGE TEMPERATURE SENSOR – EVAPORATOR AC5 2-WAY / GREY AIR DISTRIBUTION BOX
DISCHARGE TEMPERATURE SENSOR – LH FC20 2-WAY BLACK AIR DISTRIBUTION BOX
DISCHARGE TEMPERATURE SENSOR – RH FC30 2-WAY BLACK AIR DISTRIBUTION BOX
DUAL COOLANT CONTROL VALVE (DIESEL) FH34 3-WAY / BLACK ENGINE COMPARTMENT, RH SIDE, REARWARD OF RADIATOR
DUAL COOLANT CONTROL VALVE (GASOLINE) CP5 3-WAY / BLACK ENGINE COMPARTMENT, RH SIDE, REARWARD OF RADIATOR
DUAL SOLAR SENSOR SL1 6-WAY / BLACK INSTRUMENT PANEL GLARE SHIELD, FRONT CENTER
FLOOR MODE ACTUATOR FC21 6-WAY / BLACK AIR DISTRIBUTION BOX
FRESH / RECIRCULATION ACTUATOR AC3 6-WAY / BLACK BLOWER INTAKE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
HUMIDITY SENSOR FC24 4-WAY / BLACK INSTRUMENT PANEL, ADJACENT TO STEERING COLUMN
IN-CAR TEMPERATURE SENSOR FC24 4-WAY / BLACK INSTRUMENT PANEL, ADJACENT TO STEERING COLUMN
LH WINDSHIELD HEATER CA122 1-WAY / BLACK CONNECTORS LOCATED IN LH UPPER ‘A’ POST
CA279 1-WAY / BLACK
LH WINDSHIELD HEATER RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R17
PANEL MODE ACTUATOR FC22 6-WAY / BLACK AIR DISTRIBUTION BOX
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
WIPER PARK HEATER / RH WINDSHIELD HEATER RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R21
WIPER PARK HEATER OR RH WINDSHIELD HEATER CA65 1-WAY / BLACK CONNECTORS LOCATED IN RH UPPER ‘A’ POST CA71 1-WAY / BLACKHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationAC7 2-WAY / GREY / CABIN HARNESS TO CLIMATE CONTROL HARNESS BEHIND PASSENGER AIRBAG
CP1 10-WAY / BLACK / INTERCOOLER PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
CP7 4-WAY / BLACK / COOLANT PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
FC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC33 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC34 16-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR ADJACENT TO BLOWER MOTOR
FH82 2-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST
FH114 2-WAY / GREY / FRONT HARNESS TO CABIN HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDEGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE GENERAL ELECTRONIC CONTROL MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Air Conditioning Control Module – Panel Pin Description and CharacteristicI FC27–1 DEFROST MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC27–3 PANEL MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC27–4 HUMIDITY SENSOR SIGNAL: VARIABLE VOLTAGE
O FC27–5 DRIVER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
O FC27–6 PASSENGER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
SS FC27–7 HUMIDITY SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
O FC27–9 FRESH / RECIRCULATION ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC27–10 FRESH / RECIRCULATION ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC27–13 DEFROST MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
SG FC27–14 IN-CAR TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC27–15 FRESH / RECIRCULATION ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC27–16 FLOOR MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
SG FC27–17 ACTUATOR SIGNAL GROUND: GROUND
O FC27–18 AUXILIARY COOLANT PUMP RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC27–19 BLOWER MOTOR RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC27–20 HEATED WIPER PARK OR HEATED WINDSHIELD RELAY(S) ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC27–21 BLOWER MOTOR CONTROL: B+ (PWM)
O FC27–22 FLOOR MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC27–23 FLOOR MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC27–24 PANEL MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC27–25 PANEL MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC27–26 DEFROST MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
C FC28–1 CAN –
PG FC28–2 POWER GROUND: GROUND
B+ FC28–3 IGNITION SWITCHED POWER SUPPLY (II): B+
I FC28–5 BLOWER MOTOR CONTROL FEEDBACK: VARIABLE FREQUENCY
I FC28–6 PASSENGER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC28–7 DUAL SOLAR SENSOR SIGNAL – LH: VOLTAGE DECREASES AS LIGHT INCREASES
SG FC28–8 AMBIENT TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC28–9 IN-CAR TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC28–10 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
SG FC28–11 ACTUATORS SIGNAL GROUND: GROUND
C FC28–12 CAN
B+ FC28–14 BATTERY POWER SUPPLY: B+
I FC28–15 PANEL ILLUMINATION (DIMMER-CONTROLLED): B+ (PWM)
SG FC28–16 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC28–17 AMBIENT TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECR EASES AS TEMPERATURE INCREASES
I FC28–18 DRIVER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREA SES AS TEMPERATURE INCREASES
SG FC28–19 LH / RH DISCHARGE TEMPERATURE SENSORS SIGNAL GROUND: GROUND
I FC28–20 DUAL SOLAR SENSOR SIGNAL – RH: VOLTAGE DECREASES AS LIGHT INCREASES
SS FC28–22 ACTUATORS SIGNAL SUPPLY VOLTAGE: NOMINAL 5 VAir Conditioning Control Module – Remote
Pin Description and CharacteristicI FC40–1 DEFROST MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC40–3 PANEL MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC40–4 HUMIDITY SENSOR SIGNAL: VARIABLE VOLTAGE
O FC40–5 DRIVER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
O FC40–6 PASSENGER SIDE DUAL COOLANT CONTROL VALVE CONTROL DRIVE: ACTIVATE = GROUND (PWM)
SS FC40–7 HUMIDITY SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
O FC40–9 FRESH / RECIRCULATION ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC40–10 FRESH / RECIRCULATION ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC40–13 DEFROST MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
SG FC40–14 IN-CAR TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC40–15 FRESH / RECIRCULATION ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
I FC40–16 FLOOR MODE ACTUATOR POSITION FEEDBACK: VARIABLE VOLTAGE
SG FC40–17 ACTUATOR SIGNAL GROUND: GROUND
O FC40–18 AUXILIARY COOLANT PUMP RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC40–19 BLOWER MOTOR RELAY ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC40–20 HEATED WIPER PARK OR HEATED WINDSHIELD RELAY(S) ACTIVATE: TO ACTIVATE, A/CCM SWITCHES CIRCUIT TO GROUND
O FC40–21 BLOWER MOTOR CONTROL: B+ (PWM)
O FC40–22 FLOOR MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC40–23 FLOOR MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC40–24 PANEL MODE ACTUATOR DRIVE – OPEN: ACTIVATE = B+
O FC40–25 PANEL MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
O FC40–26 DEFROST MODE ACTUATOR DRIVE – CLOSE: ACTIVATE = B+
C FC41–1 CAN –
PG FC41–2 POWER GROUND: GROUND
B+ FC41–3 IGNITION SWITCHED POWER SUPPLY (II): B+
I FC41–5 BLOWER MOTOR CONTROL FEEDBACK: VARIABLE FREQUENCY
I FC41–6 PASSENGER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC41–7 DUAL SOLAR SENSOR SIGNAL – LH: VOLTAGE DECREASES AS LIGHT INCREASES
SG FC41–8 AMBIENT TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC41–9 IN-CAR TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FC41–10 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREASES AS TEMPERATURE INCREASES
SG FC41–11 ACTUATORS SIGNAL GROUND: GROUND
C FC41–12 CAN +
B+ FC41–14 BATTERY POWER SUPPLY: B+
SG FC41–16 EVAPORATOR DISCHARGE TEMPERATURE SENSOR SIGNAL GROUND: GROUND
I FC41–17 AMBIENT TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECR EASES AS TEMPERATURE INCREASES
I FC41–18 DRIVER SIDE DISCHARGE TEMPERATURE SENSOR SIGNAL: NTC SENSOR / VOLTAGE DECREA SES AS TEMPERATURE INCREASES
SG FC41–19 LH / RH DISCHARGE TEMPERATURE SENSORS SIGNAL GROUND: GROUND
I FC41–20 DUAL SOLAR SENSOR SIGNAL – RH: VOLTAGE DECREASES AS LIGHT INCREASES
SS FC41–22 ACTUATORS SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
Page 91 of 200
Climate Control System; Windshield Heaters
Jaguar S-TYPE 2005
Climate Control System; Windshield Heaters
Fig. 06.1
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f06_1_200045
RW
B NG NW
NW
FC40 / 27-01FC40 / 27-03FC40 / 27-05
FC41/28-12FC41/28-14FC41/28-01FC41/28-03
FC40 / 27-06FC40 / 27-09FC40 / 27-10FC40 / 27-17FC40 / 27-18FC40 / 27-19FC40 / 27-22FC40 / 27-23FC40 / 27-20FC40 / 27-24FC40 / 27-26FC41 / 28-02FC40 / 27-25FC41 / 28-05FC41 / 28-07FC41 / 28-09FC41 / 28-06FC41 / 28-10
WU
NWWRWB (LHD)NGB YBY WYU WUNRBGNGNRWUWRNRWBWR YRNG NWWWB
FC40 / 27-13FC40 / 27-15FC40 / 27-16FC40 / 27-14
G Y
NR
NR
88
FC41 / 28-11
FC28-15
FC41 / 28-17FC41 / 28-16FC41 / 28-19
WU NR
UY
NWR
FC41 / 28-22FC41 / 28-08FC41 / 28-20
YGWNG
FC41 / 28-18
WG (LHD)
FC41 / 28-06
WG (RHD)
FC41 / 28-18
WB (RHD)
40II
FC40 / 27-04
WG
FC40 / 27-07
NG
FC40 / 27-21
WU
NG
NG WG WR
GW
NW WB
FC24
-1 FC24
-3WU NR
AC5-2 AC5
-1WR NR
FH30 -1 FH30
-2WU NW
AC3
-1
AC3-6
AC3
-3
AC3 -4 AC3
-5
YR
WR WR YR NR
FC29
-1
FC29-6
FC29-3
FC29-4 FC29
-5
YB
WB
WB
YB NW
FC22
-1
FC22-6
FC22-3
FC22 -4 FC22
-5
Y
W
W
YN
FC21
-6
FC21-1
FC21 -3
FC21-5 FC21
-4
YU
WU WU
YU NW
LH RH
FC24
-2 FC24
-4NG WG
WU
NGWU
FC34
-3 FC34
-7
FC4-1 FC4
-8
FC34 -6 FC34
-15 FC34
-14
FC34 -4NR
FC34-11YRFCS23
FCS32
CAN
FC4 -9
FC4
-10
70
†CP34-3
*CP5-3*CP1 -2
*CP1 -3 *CP1
-1†CP34-2
*CP5-2 †CP34-1
*CP5-1
NW
NW Y NG
NG
6364677268
N
N
Y
Y
NR
NR
RU
3
1
5
2
R21
4
3
1
5
2
R7
4
NG RW
NG
NG
1213
BG
R
3
1
5
2
R7
4
R
B
AC2
-3 AC2
-6
WU
FC34 -5 FC34
-12 FC33
-5
CA50
(CA30)
CA279-1
CA122-1
RW
B
CA30
CA65-1
CA71-1
RU
BCA50
3
1
5
2
R17
4
FC10
-5
B*CP4-2†CP6-2
*CP4-1†CP6-1
RW
*CP1-4
†CP7-2
FH42B
FC10 -9
FC38
LH DISCHARGE
TEMPERATURE SENSOR RH DISCHARGE
TEMPERATURE SENSOR DUAL
SOLAR
SENSOR HUMIDITY
SENSOR
IN-CAR
TEMPERATURE SENSOR AMBIENT
TEMPERATURE SENSOR FRESH / RECIRCULATION
ACTUATOR DEFROST MODE
ACTUATOR PANEL MODE
ACTUATOR FLOOR MODE
ACTUATOR
EVAPORATOR
DISCHARGE
TEMPERATURE SENSORFC20
-1 FC20
-2 FC30
-1 FC30
-2 SL1
-1 SL1
-5 SL1
-6
SL1
-2
AIR CONDITIONING CONTROL MODULE
DUAL COOLANT CONTROL VALVE BLOWER MOTOR BLOWER MOTOR
RELAY AUXILIARY
COOLANT PUMP*
AUXILIARY COOLANT PUMPRELAY*
INSTRUMENT CLUSTER:
AUTO HEADLAMPS
INSTRUMENT CLUSTER: GROUND
REFER TO APPENDIX
CAN / A/CCM MESSAGES
DIMMER CONTROLLED LIGHTING:
PANEL ILLUMINATION -
CONTROL PANEL ONLY.
NOTE: Mirror Heaters and Heated Rear
Window controlled via A/CCM / CAN / SCP /
FEM / DDM. Refer to Fig. 10.2.
NOTE: Remote A/CCM (navigation): FC40 / FC41;
A/CCM with control panel: FC27 / FC28.
Connector numbers are shown as FC40 / 27 and FC41 / 28.
NOTE: For Air Conditioning Compressor and Refrigerent Pressure Sensor circuits;
refer to Figures 03.2, 03.4, 03.6 or 03.8 . NOTE:
* V8 only; † Diesel only
08.3 08.2 08.1
08.3 08.2
09.2
20.1
20.1 08.1
REAR POWER DISTRIBUTION FUSE BOX
FRONT POWER DISTRIBUTION FUSE BOX
LH WINDSHIELD HEATER
LH WINDSHIELD HEATERRELAY
WIPER PARK HEATER OR
RH WINDSHIELD HEATER WIPERPARKHEATER/
RH WINDSHIELD HEATER RELAY
IIIOOOOOI
ICC
IIIIIIIIIIIIOOOOOOOOOP
B
+B+
AC7-1
DRIVER PASSENGER AC2-1
AC7-2
*CP1-5
†CP7-1 FH114-1
FH82-1
SL3
-8 SL3
-3 SL3
-6 SL3
-2
FCS31
NOTE:
* Gasoline only;
† Diesel only
VARIANT: All Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004
Page 92 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 07.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
ENGINE COOLANT LEVEL SENSOR CP3 2-WAY / BLACK ENGINE COMPARTMENT, COOLANT EXPANSION TANK
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FUEL LEVEL SENSOR – LH SIDE (DIESEL) FP14 2-WAY / BLACK FUEL TANK, LH SIDE
FUEL LEVEL SENSOR – LH SIDE (GASOLINE) FP3 4-WAY / BLACK FUEL TANK, LH SIDE
FUEL LEVEL SENSOR – RH SIDE (DIESEL) FP13 6-WAY / GREY FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (GASOLINE) FP4 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (NAS N/A ONLY) FP8 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (NAS SC ONLY) FP9 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LOW LEVEL SWITCH (DIESEL) FP13 6-WAY / GREY FUEL TANK, RH SIDE
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
OIL PRESSURE SWITCH (DIESEL) C29 1-WAY / BLACK ADJACENT TO OIL FILTER
OIL PRESSURE SWITCH (GASOLINE) PI46 1-WAY / BLACK ADJACENT TO OIL FILTER
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
WASHER FLUID LEVEL SWITCH FH37 2-WAY / BLACK WASHER FLUID CONTAINERHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationCP1 10-WAY / BLACK / INTERCOOLER PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
CP7 4-WAY / BLACK / FRONT END HARNESS ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
FC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
FP6 2-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA156 LUGGAGE COMPARTMENT, RH SIDE
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Front Electronic Module Pin Description and CharacteristicI FH9–15 WASHER FLUID LEVEL SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
I FH59–9 ENGINE OIL PRESSURE SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
PG FH59–12 POWER GROUND: GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUNDInstrument ClusterPin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
I FC8–3 SEAT BELT AUDIBLE WARNING REQUEST: AUDIBLE WARNING REQUEST ACTIVE = GROUND
B+ FC8–4 IGNITION SWITCHED POWER SUPPLY (I): B+
I FC8–5 KEY-IN AUDIBLE WARNING: B+ WHEN KEY IN
I FC8–6 KEY-IN AUDIBLE WARNING (J-GATE): GROUND WHEN NOT-IN-PARK
B+ FC8–14 IGNITION SWITCHED POWER SUPPLY (II): B+
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
I FC8–19 LOW ENGINE COOLANT LEVEL WARNING: GROUND WHEN COOLANT LEVEL LOW
I FC8–23 AIR BAG WARNING: HARD-WIRED TO AIR BAG INDICATOR
B+ FC8–24 IGNITION SWITCHED POWER SUPPLY (II) (AIRBAG WARNING): B+
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–1 TRIP COMPUTER – MESSAGE CENTER SIGNALS: VARIABLE RESISTANCE
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
C FC9–12 CAN +
C FC9–13 CAN –
I FC9–17 TRIP CYCLE SWITCH – MESSAGE CENTER SIGNAL: VARIABLE RESISTANCE
S FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –Rear Electronic ModulePin Description and CharacteristicB+ CA101–3 BATTERY POWER SUPPLY: B+
I CA101–15 GASOLINE, RH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
I CA101–16 GASOLINE, LH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–17 LOW LEVEL SWITCH
I CA102–20 LOW LEVEL SWITCH
PG CA103–11 POWER GROUND: GROUND
PG CA103–12 POWER GROUND: GROUND
I CA103–17 DIESEL, RH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
I CA103–18 DIESEL, LH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
SG CA103–23 FUEL LEVEL SENSORS SIGNAL GROUND: GROUND
PG CA103–25 POWER GROUND: GROUND
PG CA103–26 POWER GROUND: GROUND
Page 94 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 08.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DUAL SOLAR SENSOR (AUTO HEADLAMP) SL1 6-WAY / BLACK INSTRUMENT PANEL GLARE SHIELD, FRONT CENTER
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FRONT FOG LAMP – LH BF4 2-WAY / BLACK FRONT BUMPER, LH SIDE
FRONT FOG LAMP – RH BF5 2-WAY / BLACK FRONT BUMPER, RH SIDE
FRONT FOG LAMP RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R11
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
HEADLAMP UNIT – LH HL2 2-WAY / BLACK ENGINE COMPARTMENT, LH FRONT
HL3 2-WAY / BLACK
HL4 2-WAY / BLACK
HL7 3-WAY / GREY
HL8 2-WAY / BLACK
HEADLAMP UNIT – RH HR2 2-WAY / BLACK ENGINE COMPARTMENT, RH FRONT HR3 2-WAY / BLACK
HR4 2-WAY / BLACK
HR7 3-WAY / GREY
HR8 2-WAY / BLACK
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
SIDE MARKER – LH BF2 2-WAY / BLACK FRONT BUMPER, LH SIDE
SIDE MARKER – RH BF3 2-WAY / BLACK FRONT BUMPER, RH SIDE
TURN REPEATER – LH FH62 2-WAY / BLACK LH FRONT FENDER
TURN REPEATER – RH FH76 2-WAY / BLACK RH FRONT FENDERHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationBF1 6-WAY / GREY / FRONT HARNESS TO FRONT BUMPER HARNESS BEHIND FRONT BUMPER, LH SIDE
FH39 12-WAY / GREY / FRONT HARNESS TO RH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, RH SIDE
FH40 12-WAY / GREY / FRONT HARNESS TO LH FRONT HEADLAMP LINK BEHIND FRONT BUMPER, LH SIDE
SL3 10-WAY / GREY / FASCIA HARNESS TO SOLAR SENSOR LINK BEHIND INSTRUMENT PANEL, RH SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Front Electronic Module Pin Description and CharacteristicO FH9–7 LH TURN SIGNAL REPEATER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH9–11 RH SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH9–19 RH TURN SIGNAL REPEATER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH9–22 LH SIDE MARKER LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUNDÅ
S FH59–1 SCP –
O FH59–2 LH FRONT SIDE LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH59–5 FRONT FOG LAMP RELAY ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
O FH59–10 RH FRONT SIDE LAMP ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
PG FH59–12 POWER GROUND: GROUND
O FH60–4 RH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH60–5 LH FRONT TURN SIGNAL ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PULSED)
O FH60–7 RH DIP BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH60–8 LH DIP BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
O FH60–10 RH MAIN BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUND
O FH60–17 LH MAIN BEAM ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUNDInstrument Cluster
Pin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
O FC8–22 HAZARD INDICATOR: PULSED B+
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–2 MAIN LIGHTING SWITCH SIGNALS – OFF, SIDE, DIP, AUTOLAMP: VARIABLE RESISTANCE
I FC9–3 MAIN LIGHTING SWITCH SIGNALS – MAIN, FLASH: VARIABLE RESISTANCE
I FC9–5 MAIN LIGHTING SWITCH SIGNALS – EXIT DELAY: VARIABLE RESISTANCE
I FC9–6 MAIN LIGHTING SWITCH SIGNALS – TURN SIGNALS, HAZARD WARNING: TURN = VARIABLE RESISTANCE; HAZARD = GROUND
I FC9–7 AUTOLAMP SENSOR SIGNAL: VARIABLE RESISTANCE
I FC9–8 FOG LAMPS SWITCH SIGNAL: VARIABLE RESISTANCE
SG FC9–9 AUTOLAMP SENSOR GROUND: GROUND
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –
Page 95 of 200
Exterior Lighting: Front
Jaguar S-TYPE 2005
Exterior Lighting: Front
Fig. 08.1
13 4114
46 80
76 77 92
ll
15 45ll ll SS
81 118EE
Fig .01.1
Fig .01 .2 F
ig .01.3
Fig .01 .4
Fig . 01.5 F
ig . 01.6 F
ig .01 .7
Input
OutputI
O
B
P+Battery VoltagePower Ground Sensor/Signal Supply V
Sensor/Signal Ground Serial and Encoded Data
CAN
+
SCPC
S DD
–
D2B Network2
f08_1_200045
FC116-4
B UYU
FC119-3
FC113-8
FC38
FC9-9
NG NG
FH9-7
U Y
O
NGFH60-15
B86
PB
20.220.2
SS
BG
FH60-14
B
P
FH60-13
B
P
FH59-12
B
P
FH60-11
B
P
FH77
SS
FC9-26 FC9-25
U Y
20.220.2
NG
FC8-2
B
FC38
85
P
B
FC8-32
B
SCP
470R
270R
180R470R 270R
180R
56R
220R270R470R220R270R470R
FC116-3
OY
FC116-1
UY
FC116-2
O
FC116-6
UY
UY
FCS5
1.2K1.2K
FC119-4B BO
FC119-7
3K9
GO
FC11-7
NG
WRGWWU
GWWRLH
RH
06.106.1
I
NG
WU
FC9-7FC9-2FC9-5FC9-6FC9-3FC9-10FC8-22FC9-8FC8-18
OIIIII
NW
FH62-2 FH62-1
NW
BO
BF2-1
NW
BW
HL8-1 HL8-2
NW
BG
HL4-1
NW
BW
HL3-1
NR
BR
HL2-2
B
BF5-2
NW
NR
FH76-1 FH76-2
NR
BW
BF3-1 BF3-2
BG
NW
BW
HL7-1 HL7-3
BF1-2
FH9-22
O
BO
FH40-3
FH60-5
O
BW
FH40-3
FH60-5
O
BW
FH40-4
FH59-2
O
BG
FH40-5
FH60-8
O
BR
FH40-6
FH60-17
O
BG
NR
BW
HR8-1 HR8-2
NR
BG
HR4-1 HR4-2
NW
BW
HR3-1 HR3-2
NR
BR
HR2-2 HR2-1
NR
BW
HR7-1 HR7-3
BO
FH9-19
O
BO
BF1-4
FH9-11
O
BW
FH39-3
FH60-4
O
BW
FH39-3
FH60-4
O
BW
FH39-4
FH59-10
O
BR
FH39-5
FH60-7
O
BW
FH39-6
FH60-10
O
BR
S53S52
S51
S58S54S48S47
S46
S49S57
B
BF4-2
NW
B
BFH22
BFS2
NW
BFS1
BG
NW
FHS62
FH59-5
O
BG
BF1-6
3
1 5
2
R11
4
59
60
NWHLS1NRHRS1
CLIMATE CONTROL: SOLAR LOAD
SL1-6SL1-5
SL1-1
SL1-2
DUAL SOLAR SENSOR (AUTO HEADLAMP)
AUTOLAMP
DIP BEAM
SIDE LAMPS
OFF
AUTOLAMP
EXIT DELAY 1
EXIT DELAY 2
EXIT DELAY 3
LH TURNRH TURN
FLASH
MAIN BEAM
MAIN LIGHTING SWITCH
(COLUMN SWITCHGEAR)
CENTER CONSOLE SWITCH PACK
HAZARD SWITCH AND INDICATOR
FOG LAMP SWITCHES
AUXILIARY LIGHTING SWITCH
FRONT
REAR
820R (LHD)
470R (RHD)
470R (LHD)
820R (RHD) FC11-5 (LHD)
FC11-6 (RHD)
GU (LHD)
WB (RHD)
INSTRUMENT CLUSTER
LOGIC
LOGIC
FC8-15
SL3-6
SL3-8 FH59-6
FH59-7 FH59-1
FRONT ELECTRONIC MODULE FRONT POWER DISTRIBUTION FUSE BOXFRONT FOG LAMP RELAY
REFER TO APPENDIX
SCP / FEM LIGHTING MESSAGES
LH TURN REPEATERLH SIDE MARKER*
LH HEADLAMP UNIT
RH TURN REPEATER RH SIDE MARKER*
RH HEADLAMP UNIT
LH FRONT FOG LAMP RH FRONT FOG LAMP
* Side Marker Lamps – NAS only.
** Either single or dual filament turn signals fitted. NOTES:
TURN **
TURN **
SIDEDIP
MAIN
TURN **
TURN ** SIDEDIP
MAIN
BF4-1
BF5-1 BF1-3HL4-2
HL3-2
HL2-1BF2-2
VARIANT: Non HID Headlamp Vehicles
VIN RANGE: All
DATE OF ISSUE: May 2004