2005 JAGUAR S TYPE fuses
[x] Cancel search: fusesPage 66 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.4
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CONDITIONING COMPRESSOR CLUTCH PI49 2-WAY / BLACK LOWER LH SIDE OF ENGINE
AIR CONDITIONING COMPRESSOR CLUTCH RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R8
AIR CONDITIONING PRESSURE SENSOR FH110 4-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, HIGH PRESSURE REFRIGERANT LINE, BETWEEN COMPRESSOR AND CONDENSER
BRAKE CANCEL SWITCH CA36 2-WAY / GREY TOP OF BRAKE PEDAL
COOLING FAN MODULE FH108 2-WAY / BLACK ENGINE COMPARTMENT, RH FRONT, REARWARD OF RADIATOR
FH109 2-WAY / BLACK
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FUEL INJECTOR 1 PI32 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 2 PI36 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 3 PI33 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 4 PI37 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 5 P34 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 6 PI38 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 7 PI35 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 8 PI39 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL PUMP 1 FP2 8-WAY / BLACK FUEL TANK, RH SIDE
FP4 (ROW) 4-WAY / BLACK
FP8 (NAS) 6-WAY / BLACK
FUEL PUMP RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R15
IGNITION CAPACITOR PI54 2-WAY / BLACK LH CYLINDER HEAD, REAR
IGNITION MODULE AND COIL 1 PI2 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 2 PI6 4-WAY / BLACK LH CYLINDER HEAD
IGNITION MODULE AND COIL 3 PI3 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 4 PI7 4-WAY / BLACK LH CYLINDER HEAD
IGNITION MODULE AND COIL 5 PI4 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 6 PI8 4-WAY / BLACK LH CYLINDER HEAD
IGNITION MODULE AND COIL 7 PI5 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 8 PI9 4-WAY / BLACK LH CYLINDER HEAD
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR
CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
STEERING WHEEL SPEED CONTROL SWITCHES SQ2 6-WAY / BLACK STEERING WHEELHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA156 LUGGAGE COMPARTMENT, RH SIDE
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH95 ENGINE COMPARTMENT, BEHIND LH HEADLAMP (RADIATOR FAN GROUND)
PI51 ENGINE COMPARTMENT, ENGINE BLOCK
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and CharacteristicI PI1–9 BRAKE CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SG PI1–19 SENSOR GROUND 1: GROUND
O PI1–27 FUEL PUMP DRIVE SIGNAL (TO REM): PWM, 150 Hz, NORMAL POSITIVE DUTY CYCLE RANGE = 4% – 51%
O PI1–34 AIR CONDITIONING COMPRESSOR CLUTCH RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SS PI1–47 SPEED CONTROL SWITCH REQUEST: STEPPED RESISTANCE
I PI1–48 SPEED CONTROL SWITCHES SIGNAL GROUND: GROUND
O PI1–51 COOLING FAN MODULE CONTROL: PWM, 140 Hz, POSITIVE DUTY CYCLE RANGE 7% – 95%
O PI1–61 IGNITION COIL ACTIVATE – CYLINDER 2: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–62 IGNITION COIL ACTIVATE – CYLINDER 4: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–63 IGNITION COIL ACTIVATE – CYLINDER 6: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–64 IGNITION COIL ACTIVATE – CYLINDER 8: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–87 IGNITION COIL ACTIVATE – CYLINDER 1: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–88 IGNITION COIL ACTIVATE – CYLINDER 3: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–89 IGNITION COIL ACTIVATE – CYLINDER 5: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–90 IGNITION COIL ACTIVATE – CYLINDER 7: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–112 FUEL INJECTOR DRIVE – CYLINDER 8: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–113 FUEL INJECTOR DRIVE – CYLINDER 5: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–114 FUEL INJECTOR DRIVE – CYLINDER 3: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–115 FUEL INJECTOR DRIVE – CYLINDER 2: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–117 FUEL INJECTOR DRIVE – CYLINDER 7: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–118 FUEL INJECTOR DRIVE – CYLINDER 6: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–119 FUEL INJECTOR DRIVE – CYLINDER 4: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–120 FUEL INJECTOR DRIVE – CYLINDER 1: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–121 AIR CONDITIONING PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: TRANSDUCER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–131 IGNITION MONITOR BANK 1: PULSED SIGNAL, 3 PULSES PER ENGINE CYCLE
I PI1–132 IGNITION MONITOR BANK 2: PULSED SIGNAL, 3 PULSES PER ENGINE CYCLERear Electronic Module
Pin Description and CharacteristicB+ CA100–8 IGNITION SWITCHED POWER SUPPLY (II): B+
B+ CA101–1 FUEL PUMP POWER SUPPLY: B+ WHEN FUEL PUMP RELAY IS ACTIVATED
SG CA101–2 LOGIC GROUND / FUEL PUMP DRIVE SHIELD: GROUND
B+ CA101–3 BATTERY POWER SUPPLY: B+
O CA101–11 FUEL PUMP SUPPLY VOLTAGE: B+
O CA101–12 FUEL PUMP ACTIVATE: GROUND (PWM)
S CA102–1 SCP +
S CA102–2 SCP –
I CA103–19 FUEL PUMP DRIVE SIGNAL: PWM, 150 Hz, NORMAL POSITIVE DUTY CYCLE RANGE = 4% – 51%
Page 68 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.5
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAPP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CKP SENSOR PI21 2-WAY / BLACK ENGINE UNDER SIDE, FORWARD OF BELL HOUSING
CMP SENSOR 1 PI23 2-WAY / BLACK BANK 1 (RH) CAMSHAFT COVER, FRONT
CMP SENSOR 2 PI22 2-WAY / BLACK BANK 2 (LH) CAMSHAFT COVER, FRONT
ECT SENSOR PI25 2-WAY / BLACK ENGINE VEE, COOLANT OUTLET CASTING
EFT SENSOR PI27 2-WAY / BLACK FUEL RAIL, RH REAR
EGR VALVE PI15 6-WAY / BLACK INTAKE MANIFOLD, REAR
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
EOT SENSOR PI24 2-WAY / BLACK ADJACENT TO OIL FILTER
EVAP CANISTER CLOSE VALVE CA270 2-WAY / BLACK ABOVE REAR AXLE (FUEL TANK COMPONENTS)
EVAP CANISTER PURGE VALVE FH111 2-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, ADJACENT TO SUSPENSION TURRET
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FTP SENSOR FP1 3-WAY / BLACK FUEL TANK PIPING, LH SIDE (UNDER ACCESS PLATE)
HO2 SENSOR DOWNSTREAM 1/2 PI11 4-WAY / BLACK RH EXHAUST, TOP OF CATALYST
HO2 SENSOR DOWNSTREAM 2/2 PI13 4-WAY / BLACK LH EXHAUST, TOP OF CATALYST
HO2 SENSOR UPSTREAM 1/1 PI10 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
HO2 SENSOR UPSTREAM 2/1 PI12 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
IAT SENSOR 2 PI43 2-WAY / BLACK INTAKE MANIFOLD, RH SIDE, REAR
IP SENSOR PI28 3-WAY / BLACK FUEL RAIL, LH REAR
KNOCK SENSOR 1 PI20 2-WAY / BLACK ENGINE VEE, BANK 1
KNOCK SENSOR 2 PI19 2-WAY / BLACK ENGINE VEE, BANK 2
MAF SENSOR PI14 5-WAY / BLACK ENGINE AIR INTAKE, ADJACENT TO AIR CLEANER
MAP SENSOR PI29 4-WAY / BLACK INTAKE MANIFOLD, REAR, BELOW THROTTLE ASSEMBLY
THROTTLE MOTOR PI18 2-WAY / BLACK ENGINE AIR INTAKE, REAR
THROTTLE MOTOR RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R5
TP SENSOR PI26 4-WAY / BLACK THROTTLE BODY, THROTTLE SHAFTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationPI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module
Pin Description and CharacteristicO PI1–1 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–2 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
PG PI1–4 POWER GROUND 1: GROUND
PG PI1–5 POWER GROUND 2: GROUND
I PI1–6 ENGINE CRANK: B+
I PI1–7 IGNITION ON: B+
I PI1–8 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I PI1–10 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SS PI1–13 SENSOR POWER SUPPLY 2: NOMINAL 5 V
SG PI1–17 SMALL SIGNAL GROUND 1: GROUND
SG PI1–18 SMALL SIGNAL GROUND 2: GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
SG PI1–20 SENSOR GROUND 2: GROUND
B+ PI1–22 BATTERY POWER SUPPLY: B+
B+ PI1–23 EMS SWITCHED POWER SUPPLY 1: B+
B+ PI1–24 EMS SWITCHED POWER SUPPLY 2: B+
SG PI1–29 HO2 SENSOR HEATER GROUND – 1/1: GROUND
SG PI1–30 HO2 SENSOR HEATER GROUND – 1/1: GROUND
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–36 CRANKSHAFT SENSOR SIGNAL: PULSED SIGNAL, 70 PULSES PER ENGINE CYCLE
SG PI1–37 CRANKSHAFT SENSOR SIGNAL GROUND: GROUND
O PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–43 TP AND APP SIGNALS SHIELD: GROUND
I PI1–44 MASS AIR FLOW SENSOR SIGNAL: NOMINAL 0 – 5 V BY ENGINE OPERATING CONDITION
SG PI1–45 MASS AIR FLOW SENSOR GROUND: GROUND
SG PI1–46 MASS AIR FLOW SENSOR GROUND: GROUND
I PI1–50 ENGINE FUEL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
O PI1–52 THROTTLE MOTOR RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–54 THROTTLE MOTOR GROUND: GROUND
O PI1–55 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–56 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–57 EGR DRIVE 1: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–58 EGR DRIVE 2: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–59 EGR DRIVE 3: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–60 EGR DRIVE 4: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–66 EVAP CANISTER PURGE VALVE DRIVE: PWM, 10 Hz, POSITIVE DUTY CYCLE RANGE 7% – 100%
O PI1–67 EVAP CANISTER CLOSE VALVE DRIVE: TO CLOSE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–68 BANK 2 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–69 BANK 2 CAMSHAFT SENSOR GROUND: GROUND
I PI1–70 ENGINE COOLANT TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–71 INTAKE AIR TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–72 INTAKE AIR TEMPERATURE SENSOR 2 SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–73 INJECTION PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: POTENTIOMETER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–75 THROTTLE POSITION SENSOR 1 SIGNAL: IDLE = 0.60 V; FULL THROTTLE = 4.30 V
I PI1–76 THROTTLE POSITION SENSOR 2 SIGNAL: IDLE = 1.48 V; FULL THROTTLE = 4.40 V
I PI1–78 ENGINE OIL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–79 GENERATOR FAULT; CHARGE WARNING
O PI1–80 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
SG PI1–81 HO2 SENSOR HEATER GROUND – 2/1: GROUND
SG PI1–82 HO2 SENSOR HEATER GROUND – 2/1: GROUND
I PI1–83 HO2 SENSOR 1/1 SIGNAL: VARIABLE CURRENT
I PI1–84 HO2 SENSOR 1/1 SIGNAL: CONSTANT CURRENT
SG PI1–91 HO2 SENSOR HEATERS 1/2, 2/2 GROUND: GROUND
O PI1–92 HO2 SENSOR HEATER CONTROL – 1/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
O PI1–93 HO2 SENSOR HEATER CONTROL – 2/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
I PI1–94 BANK 1 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–95 BANK 1 CAMSHAFT SENSOR GROUND: GROUND
I PI1–98 BANK 1 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
I PI1–99 BANK 2 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
SG PI1–100 SENSOR SHIELD: GROUND
I PI1–102 ACCELERATOR PEDAL POSITION SENSOR 1 SIGNAL: FOOT OFF = 0.75 V; FULLY DEPRESSED = 3.40 V (AUTO) 3.20 V (MAN)
I PI1–103 ACCELERATOR PEDAL POSITION SENSOR 2 SIGNAL: FOOT OFF = 3.38 V; FULLY DEPRESSED = 2.05 V (AUTO) 2.14 V (MAN)
I PI1–104 FUEL TANK PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
D PI1–105 SERIAL DATA LINK: SERIAL COMMUNICATION
O PI1–106 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
I PI1–107 HO2 SENSOR 2/1 SIGNAL: VARIABLE CURRENT
I PI1–108 HO2 SENSOR 2/1 SIGNAL: CONSTANT CURRENT
SG PI1–111 FUEL INJECTORS 2, 3, 5, 8 GROUND: GROUND
SG PI1–116 FUEL INJECTORS 1, 4, 6, 7 GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +
I PI1–127 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I PI1–128 HO2 SENSOR 1/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
I PI1–129 HO2 SENSOR 2/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
SG PI1–130 HO2 SENSORS SHIELD: GROUND
B+ PI1–134 THROTTLE MOTOR POWER SUPPLY: B+ WHEN RELAY ACTIVATED
Page 70 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.6
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CLEANER SOLENOID VALVE FH10 2-WAY / BLACK AIR CLEANER HOUSING
AIR CONDITIONING COMPRESSOR CLUTCH PI49 2-WAY / BLACK LOWER LH SIDE OF ENGINE
AIR CONDITIONING COMPRESSOR CLUTCH RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R8
AIR CONDITIONING PRESSURE SENSOR FH110 4-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, HIGH PRESSURE REFRIGERANT LINE, BETWEEN COMPRESSOR AND CONDENSER
BRAKE CANCEL SWITCH CA36 2-WAY / GREY TOP OF BRAKE PEDAL
COOLING FAN MODULE FH108 2-WAY / BLACK ENGINE COMPARTMENT, RH FRONT, REARWARD OF RADIATOR
FH109 2-WAY / BLACK
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FUEL INJECTOR 1 (V8 SC) IS1 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 2 (V8 SC) IS7 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 3 (V8 SC) IS2 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 4 (V8 SC) IS8 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 5 (V8 SC) IS3 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 6 (V8 SC) IS9 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 7 (V8 SC) IS4 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL INJECTOR 8 (V8 SC) IS10 2-WAY / BLACK FUEL RAIL / INTAKE MANIFOLD
FUEL PUMP 1 FP2 8-WAY / BLACK FUEL TANK, RH SIDE
FP4 (ROW) 4-WAY / BLACK
FP8 (NAS) 6-WAY / BLACK
FUEL PUMP 2 FP2 8-WAY / BLACK FUEL TANK, LH SIDE
FP3 (ROW) 4-WAY / BLACK
FP9 (NAS) 6-WAY / BLACK
FUEL PUMP 2 MODULE CA283 10-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR
FUEL PUMP RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R15
IGNITION CAPACITOR PI54 2-WAY / BLACK LH CYLINDER HEAD, REAR
IGNITION MODULE AND COIL 1 PI2 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 2 PI6 4-WAY / BLACK LH CYLINDER HEAD
IGNITION MODULE AND COIL 3 PI3 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 4 PI7 4-WAY / BLACK LH CYLINDER HEAD
IGNITION MODULE AND COIL 5 PI4 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 6 PI8 4-WAY / BLACK LH CYLINDER HEAD
IGNITION MODULE AND COIL 7 PI5 4-WAY / BLACK RH CYLINDER HEAD
IGNITION MODULE AND COIL 8 PI9 4-WAY / BLACK LH CYLINDER HEAD
INTERCOOLER PUMP CP2 2-WAY / BLACK ENGINE COMPARTMENT, RH SIDE, ADJACENT TO RADIATOR
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
STEERING WHEEL SPEED CONTROL SWITCHES SQ2 6-WAY / BLACK STEERING WHEELHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationCP1 10-WAY / BLACK / INTERCOOLER PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
FC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
IS5 6-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK ENGINE, LH REAR
IS6 6-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK ENGINE, RH REAR
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA156 LUGGAGE COMPARTMENT, RH SIDE
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH95 ENGINE COMPARTMENT, BEHIND LH HEADLAMP (RADIATOR FAN GROUND)
PI51 ENGINE COMPARTMENT, ENGINE BLOCK
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and CharacteristicI PI1–9 BRAKE CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATED
I PI1–11 FUEL PUMP 2 MODULE MONITOR: 1 Hz FREQUENCY; 50% DUTY CYCLE = OK, 25% OR 75% DUTY CYCLE = FAULT
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
O PI1–14 AIR CLEANER SOLENOID VALVE DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
O PI1–27 FUEL PUMP DRIVE SIGNAL (TO REM): PWM, 150 Hz, NORMAL POSITIVE DUTY CYCLE RANGE = 4% – 51%
O PI1–34 AIR CONDITIONING COMPRESSOR CLUTCH RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SS PI1–47 SPEED CONTROL SWITCH REQUEST: STEPPED RESISTANCE
I PI1–48 SPEED CONTROL SWITCHES SIGNAL GROUND: GROUND
O PI1–51 COOLING FAN MODULE CONTROL: PWM, 140 Hz, POSITIVE DUTY CYCLE RANGE 7% – 95%
O PI1–53 FUEL PUMP 2 DRIVE (TO FUEL PUMP 2 MODULE): PWM, 150 Hz, NORMAL POSITIVE DUTY CYCLE RANGE = 4% – 51%
O PI1–61 IGNITION COIL ACTIVATE – CYLINDER 2: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–62 IGNITION COIL ACTIVATE – CYLINDER 4: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–63 IGNITION COIL ACTIVATE – CYLINDER 6: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–64 IGNITION COIL ACTIVATE – CYLINDER 8: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–87 IGNITION COIL ACTIVATE – CYLINDER 1: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–88 IGNITION COIL ACTIVATE – CYLINDER 3: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–89 IGNITION COIL ACTIVATE – CYLINDER 5: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–90 IGNITION COIL ACTIVATE – CYLINDER 7: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–112 FUEL INJECTOR DRIVE – CYLINDER 8: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–113 FUEL INJECTOR DRIVE – CYLINDER 5: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–114 FUEL INJECTOR DRIVE – CYLINDER 3: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–115 FUEL INJECTOR DRIVE – CYLINDER 2: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–117 FUEL INJECTOR DRIVE – CYLINDER 7: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–118 FUEL INJECTOR DRIVE – CYLINDER 6: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–119 FUEL INJECTOR DRIVE – CYLINDER 4: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–120 FUEL INJECTOR DRIVE – CYLINDER 1: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–121 AIR CONDITIONING PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: TRANSDUCER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–131 IGNITION MONITOR BANK 1: PULSED SIGNAL, 3 PULSES PER ENGINE CYCLE
I PI1–132 IGNITION MONITOR BANK 2: PULSED SIGNAL, 3 PULSES PER ENGINE CYCLERear Electronic Module
Pin Description and CharacteristicB+ CA100–8 IGNITION SWITCHED POWER SUPPLY (II): B+
B+ CA101–1 FUEL PUMP POWER SUPPLY: B+ WHEN FUEL PUMP RELAY IS ACTIVATED
SG CA101–2 LOGIC GROUND / FUEL PUMP DRIVE SHIELD: GROUND
B+ CA101–3 BATTERY POWER SUPPLY: B+
O CA101–11 FUEL PUMP SUPPLY VOLTAGE: B+
O CA101–12 FUEL PUMP ACTIVATE: GROUND (PWM)
S CA102–1 SCP +
S CA102–2 SCP –
I CA103–19 FUEL PUMP DRIVE SIGNAL: PWM, 150 Hz, NORMAL POSITIVE DUTY CYCLE RANGE = 4% – 51%
Page 72 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.7
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationACT SENSOR C69 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
APP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / BLACK TOP OF BRAKE PEDAL
CKP SENSOR C77 3-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
CMP SENSOR C25 3-WAY / GREY REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
ECT SENSOR C34 2-WAY / GREY REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
EFT SENSOR C35 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
EGR VALVE 1 C70 6-WAY / GREY REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
EGR VALVE 2 C71 6-WAY / GREY REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
EOT SENSOR C28 3-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
FRP SENSOR C30 3-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
INLET PORT DEACTIVATION SOLENOID C36 4-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
KNOCK SENSOR 1 C87 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
KNOCK SENSOR 2 C88 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
MAF SENSOR 1 FH14 4-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
MAF SENSOR 2 FH15 4-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
MAP SENSOR C31 3-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
POWERTRAIN CONTROL MODULE C98 48-WAY / BROWN FRONT BULKHEAD, PASSENGER SIDE C99 48-WAY / GREY
FH13 48-WAY / BLACK
ROTARY ELECTRONIC ACTUATOR 1 C40 5-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
ROTARY ELECTRONIC ACTUATOR 2 C41 5-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
EGR THROTTLE BODY C39 6-WAY / GREY REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationFH4 ENGINE COMPARTMENT, REARWARD OF RH WHEEL ARCH
NOTE: SG* indicates shared-signal grounds, (sharing sensors shown in parentheses).
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Powertrain Control Module Pin Description and CharacteristicC C98–A3 CAN +
C C98–A4 CAN –
I C98–C4 KNOCK SENSOR 2 SIGNAL: DIFFERENTIAL –ve. VOLTAGE DEPENDENT ON ENGINE VIBRATION
I C98–D1 FRP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCR EASES AS PRESSURE INCREASES
I C98–D3 KNOCK SENSOR 2 SIGNAL: DIFFERENTIAL +ve. VOLTAGE DEPENDENT ON ENGINE VIBRATION
I C98–D4 KNOCK SENSOR 1 SIGNAL: DIFFERENTIAL –ve. VOLTAGE DEPENDENT ON ENGINE VIBRATION
I C98–E1 EGR THROTTLE POSITION SENSOR SIGNAL: NOMINAL 0 – 5 V
I C98–E4 KNOCK SENSOR 1 SIGNAL: DIFFERENTIAL +ve. VOLTAGE DEPENDENT ON ENGINE VIBRATION
I C98–F3 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
O C98–H3 ROTARY ELECTRONIC ACTUATOR 1, VARIABLE VANE TURBO: PWM, 300 Hz
O C98–H4 ROTARY ELECTRONIC ACTUATOR 2, VARIABLE VANE TURBO: PWM, 300 Hz
O C98–K4 INLET PORT DEACTIVATION SOLENOID: PWM, 250 Hz
SG C98–C3 CAN SHIELD: GROUND
SG C98–E2 FRP SENSOR GROUND: GROUND
SG C98–F2 EGR THROTTLE POSITION SENSOR GROUND: GROUND
SS C98–D2 FRP SENSOR POWER SUPPLY: NOMINAL 5 V
SS C98–F1 EGR THROTTLE POSITION SENSOR POWER SUPPLY: NOMINAL 5 V
I C99–A2 EGR VALVE POSITION SENSOR 2: NOMINAL 0 – 5 V
I C99–A3 EGR VALVE POSITION SENSOR 1: NOMINAL 0 – 5 V
I C99–B1 ACT SENSOR SIGNAL: NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECR EASES AS TEMPERATURE INCREASES
I C99–B2 EFT SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECRE ASES AS TEMPERATURE INCREASES
I C99–C1 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCR EASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I C99–C2 ECT SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECR EASES AS TEMPERATURE INCREASES
I C99–E1 EOT SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECRE ASES AS TEMPERATURE INCREASES
I C99–F1 CKP SENSOR SIGNAL: PULSED SIGNAL, 70 PUL SES PER ENGINE CYCLE
I C99–F2 GENERATOR FAULT; CHARGE WARNING
I C99–G4 CMP SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
O C99–H1 EGR VALVE 1: +ve PWM
O C99–H2 EGR VALVE 1: –ve PWM
O C99–J1 EGR VALVE 2: +ve PWM
O C99–J4 EGR THROTTLE MOTOR DRIVE: +ve PWM
O C99–K1 EGR VALVE 2: –ve PWM
O C99–K4 EGR THROTTLE MOTOR DRIVE: –ve PWM
SG C99–G2 CKP SENSOR SIGNAL GROUND: GROUND
SG C99–H3 CMP SENSOR GROUND: GROUND
SG* C99–D2 EGR VALVE POSITION SENSOR 1 GROUND (EOT SENSOR): GROUND
SG* C99–D2 EOT SENSOR GROUND (EGR VALVE POSITION SENSOR 1): GROUND
SG* C99–E2 ECT SENSOR GROUND (MAP SENSOR): GROUND
SG* C99–E2 MAP SENSOR GROUND (ECT SENSOR): GROUND
SG* C99–G3 ACT SENSOR GROUND (EGR VALVE 2, EFT SENSOR): GROUND
SG* C99–G3 EGR VALVE POSITION SENSOR 2 GROUND (ACT SENSOR, EFT SENSOR): GROUND
SG* C99–G3 EFT SENSOR GROUND (ACT SENSOR, EGR VALVE POSITION SENSOR 2): GROUND
SS C99–C3 EGR VALVE POSITION SENSORS POWER SUPPLY: NOMINAL 5 V
SS C99–C3 EOT SENSOR POWER SUPPLY: NOMINAL 5 V
SS C99–D1 MAP SENSOR POWER SUPPLY: NOMINAL 5 V
SS C99–G1 CKP SENSOR POWER SUPPLY: NOMINAL 5 V
SS C99–H4 CMP SENSOR POWER SUPPLY: NOMINAL 5 V
SG FH13–A2 APP SENSOR SHIELD: GROUND
O FH13–B1 STARTER RELAY DRIVE: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
SG FH13–B2 APP SENSOR 2 GROUND: GROUND
I FH13–B4 SPEED CONTROL SWITCHES SIGNAL GROUND: GROUND
SG FH13–C1 APP SENSOR 1 GROUND: GROUND
I FH13–C2 APP SENSOR 2 SIGNAL: NEGATIVE-GOING VOLTAGE SLOPE, TYPICAL IDLE VOLTAGE = 3. 445V TO 3.305V; TYPICAL FULL PEDAL VOLTAGE = 2.05 V
SS FH13–C4 SPEED CONTROL SWITCH REQUEST: STEPPED RESISTANCE
I FH13–D1 APP SENSOR 1 SIGNAL: POSITIVE-GOING VOLTAGE SLOPE, TYPICAL IDLE VOLTAGE = 0.61V TO 0.89V; TYPICAL FULL PEDAL VOLTAGE = 3 .4 V
SS FH13–D2 APP SENSOR 2 POWER SUPPLY: NOMINAL 5 V
I FH13–D4 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED
SS FH13–E1 APP SENSOR 1 POWER SUPPLY: NOMINAL 5 V
I FH13–E3 BRAKE CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATED
I FH13–F1 IAT SENSOR (INTEGRAL TO MAF SENSOR) SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I FH13–F3 ENGINE CRANK: B+
I FH13–F4 MAF SENSOR 1 SIGNAL: TIME PERIOD (FREQUENCY) SIGNAL, PROPORTIONAL TO AIR FLOW
I FH13–G2 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I FH13–G4 MAF SENSOR 2 SIGNAL: TIME PERIOD (FREQUENCY) SIGNAL, PROPORTIONAL TO AIR FLOW
O FH13–J3 EMS CONTROL RELAY DRIVE: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
O FH13–K2 COOLING FAN MODULE CONTROL: PWM, 140 Hz, POSITIVE DUTY CYCLE RANGE 7% – 95%
B+ FH13–K3 IGNITION SWITCHED POWER (RUN): PJB, F4, 5A
B+ FH13–K4 BATTERY POWER SUPPLY: B+
B+ FH13–L1 EMS SWITCHED POWER SUPPLY 1: FPDB, F20, 30A
B+ FH13–L2 EMS SWITCHED POWER SUPPLY 2: FPDB, F20, 30A
B+ FH13–L3 EMS SWITCHED POWER SUPPLY 3: FPDB, F20, 30A
SG FH13–L4 MAF (INTEGRAL IAT) SENSORS GROUND: GROUND
PG FH13–M1 POWER GROUND: GROUND
PG FH13–M2 POWER GROUND: GROUND
PG FH13–M3 POWER GROUND: GROUND
PG FH13–M4 POWER GROUND: GROUND
Page 74 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.8
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CONDITIONING COMPRESSOR CLUTCH C67 2-WAY / BLACK LOWER LH SIDE OF ENGINE
AIR CONDITIONING COMPRESSOR CLUTCH RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R8
AIR CONDITIONING PRESSURE SENSOR FH110 3-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, HIGH PRESSURE REFRIGERANT LINE, BETWEEN COMPRESSOR AND CONDENSER
BRAKE CANCEL SWITCH CA36 2-WAY / GREY TOP OF BRAKE PEDAL
COOLING FAN MODULE FH120 4-WAY / BLACK ENGINE COMPARTMENT, RH FRONT, REARWARD OF RADIATOR
DOSING PUMP CA307 2-WAY / BLACK FUEL TANK, RH SIDE, ABOVE FUEL FILLER HOSE
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FUEL-FIRED AUXILIARY HEATER MODULE FH24 8-WAY / BLACK BELOW LH HEADLAMP ASSEMBLY
FH25 2-WAY / BLACK
FUEL INJECTOR 1 C44 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
FUEL INJECTOR 2 C46 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
FUEL INJECTOR 3 C48 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
FUEL INJECTOR 4 C45 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
FUEL INJECTOR 5 C47 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
FUEL INJECTOR 6 C49 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
FUEL LIFT PUMP FP2 8-WAY / BLACK FUEL TANK, RH SIDE
FUEL LIFT PUMP RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R15
GLOW PLUG CONTROL MODULE FH20 5-WAY / BLACK ENGINE COMPARTMENT, RH FRONT, BRACKET, DSC MODULE
FH23 EYELET
GP4 6-WAY
GLOW PLUGS (BANK 1) GP1 3-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
GLOW PLUGS (BANK 2) GP2 3-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
POWERTRAIN CONTROL MODULE C98 48-WAY / BROWN FRONT BULKHEAD, PASSENGER SIDE C99 48-WAY / GREY
FH13 48-WAY / BLACK
PRESSURE CONTROL VALVE (FUEL PUMP) C43 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR
CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENT
STEERING WHEEL SPEED CONTROL SWITCHES SQ2 6-WAY / BLACK STEERING WHEEL
VOLUMETRIC CONTROL VALVE (FUEL PUMP) C42 2-WAY / BLACK REFER TO SENSORS AND ACTUATORS, PAGE 32 OR 33HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FH6 6-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK ENGINE, LH REAR
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA52 LH ‘C’ POST, UPPER
CA156 LUGGAGE COMPARTMENT, RH SIDE
FH22 ENGINE COMPARTMENT, BEHIND LH HEADLAMP
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH95 ENGINE COMPARTMENT, BEHIND LH HEADLAMP (RADIATOR FAN GROUND)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Powertrain Control Module Pin Description and CharacteristicI C98–E3 GLOW PLUG CONTROL MODULE LOGIC MONITOR
O C98–G3 GLOW PLUG CONTROL MODULE DRIVE: PWM, 100% = 0N, 0% = OFF
O C98–J4 FUEL PUMP, VOLUMETRIC CONTROL VALVE: PWM, 200 Hz
O C98–K3 FUEL PUMP, PRESSURE CONTROL VALVE: PWM, 350 Hz
O C98–L1 FUEL INJECTOR DRIVE – CYLINDER 4: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
+ C98–L2 FUEL INJECTOR POWER SUPPLY – CYLINDER 4:
+ C98–L3 FUEL INJECTOR POWER SUPPLY – CYLINDER 5:
O C98–M1 FUEL INJECTOR DRIVE – CYLINDER 5: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
O C98–M2 FUEL INJECTOR DRIVE – CYLINDER 6: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
O C98–M3 FUEL INJECTOR POWER SUPPLY – CYLINDER 6:
+ C99–L2 FUEL INJECTOR POWER SUPPLY – CYLINDER 2:
+ C99–L3 FUEL INJECTOR POWER SUPPLY – CYLINDER 1:
+ C99–L4 FUEL INJECTOR POWER SUPPLY – CYLINDER 3:
O C99–M2 FUEL INJECTOR DRIVE – CYLINDER 2: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
+ C99–M3 FUEL INJECTOR DRIVE – CYLINDER 1: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
O C99–M4 FUEL INJECTOR DRIVE – CYLINDER 3: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
SG FH13–B3 AIR CONDITIONING PRESSURE SENSOR GROUND
SG FH13–B4 SPEED CONTROL SWITCHES SIGNAL GROUND: GROUND
I FH13–C4 SPEED CONTROL SWITCH REQUEST: STEPPED RESISTANCE
SS FH13–D3 AIR CONDITIONING PRESSURE SENSOR POWER SUPPLY: NOMINAL 5 V
I FH13–E3 BRAKE CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATED
I FH13–F2 AIR CONDITIONING PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: TRANSDUCER – VOLTAGE INCREASES AS PRESSURE INCREASES
O FH13–J2 AIR CONDITIONING COMPRESSOR CLUTCH RELAY DRIVE: TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
O FH13–J4 FUEL LIFT PUMP DRIVE SIGNAL (TO FUEL LIFT PUMP RELAY): TO ACTIVATE, PCM SWITCHES CIRCUIT TO GROUND
O FH13–K2 COOLING FAN MODULE CONTROL: PWM, 140 Hz, POSITIVE DUTY CYCLE RANGE 7% – 95%
Page 76 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 04.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationIGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
J-GATE MODULE CA245 16-WAY / BLACK J-GATE ASSEMBLY
TRANSMISSION CAPACITOR (V6) GB17 2-WAY / BLACK ENGINE COMPARTMENT, BULKHEAD
TRANSMISSION CAPACITOR (V8) PI59 2-WAY / BLACK ENGINE COMPARTMENT, BULKHEAD
TRANSMISSION CONTROL MODULE GB2 16-WAY / BLACK TRANSMISSION CONTROL VALVE ASSEMBLYHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA154 UNDER LH FRONT SEAT
FH4 ENGINE COMPARTMENT, REARWARD OF RH WHEEL ARCH
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Transmission Control Module Pin Description and CharacteristicC GB2–2 CAN –
D GB2–3 SERIAL COMMUNICATION
C GB2–6 CAN +
B+ GB2–9 IGNITION SWITCHED POWER SUPPLY: B+
O GB2–10 PARK / NEUTRAL SIGNAL: GROUND WHEN ACTIVATED
PG GB2–13 POWER GROUND: GROUND
B+ GB2–14 BATTERY POWER SUPPLY: B+
PG GB2–16 POWER GROUND: GROUND
Page 78 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 04.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCLUTCH CANCEL SWITCH CA285 (RHD) 2-WAY / BLACK TOP OF CLUTCH PEDAL (TOP SWITCH)
CA291 (LHD) 5-WAY / BLACK
CLUTCH PEDAL POSITION SENSOR CA287 6-WAY / BLACK TOP OF CLUTCH PEDAL
CLUTCH PEDAL SAFETY SWITCH CA286 2-WAY / BLACK TOP OF CLUTCH PEDAL (BOTTOM SWITCH)
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
NEUTRAL SWITCH (DIESEL) GB4 4-WAY / GREY TRANSMISSION, LH REAR
NEUTRAL SWITCH (GASOLINE) GB3 2-WAY / BLACK TRANSMISSION, LH REAR
PARKING BRAKE MODULE CA265 14-WAY / GREY LUGGAGE COMPARTMENT, RH REAR CA266 24-WAY / BLACK
POWERTRAIN CONTROL MODULE C98 48-WAY / BROWN FRONT BULKHEAD, PASSENGER SIDE C99 48-WAY / GREY
FH13 48-WAY / BLACK
REVERSE SWITCH GB5 2-WAY / BLACK TRANSMISSION, LH REARHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
GB1 16-WAY / GREY / ENGINE HARNESS TO TRANSMISSION HARNESS ADJACENT TO TRANSMISSION BELL HOUSING
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDE
PI42 8-WAY / BLACK / ENGINE HARNESS TO FRONT HARNESS ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationFH4 ENGINE COMPARTMENT, REARWARD OF RH WHEEL ARCH
PI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
Parking Brake Module Pin Description and CharacteristicI CA265–3 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
SS CA265–5 CLUTCH PEDAL POSITION SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
I CA265–6 CLUTCH PEDAL POSITION SENSOR FEEDBACK SIGNAL: VARIABLE VOLTAGE
SG CA266–3 CLUTCH PEDAL POSITION SENSOR GROUND: GROUND
I CA266–15 IN-GEAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUNDEngine Control Module (Gasoline)Pin Description and CharacteristicI PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–33 CLUTCH CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATEDPowertrain Control Module (Diesel)
Pin Description and CharacteristicI FH13–G3 CLUTCH CANCEL SWITCH: NORMALLY CLOSED / GROUND WHEN ACTIVATED
Page 80 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationACTIVE BRAKE BOOSTER — — ENGINE COMPARTMENT BULKHEAD, DRIVER SIDE
ACTIVE BRAKE BOOSTER SOLENOID FH56 6-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
BRAKE FLUID RESERVOIR FH104 2-WAY / BLACK BRAKE BOOSTER
BRAKE PRESSURE SENSOR FH54 3-WAY / BLACK BRAKE MASTER CYLINDER, UNDERSIDE
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE
FC119 8-WAY / BLACK
DYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
PEDAL FORCE SWITCH FH56 6-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
PEDAL TRAVEL SENSOR FH11 3-WAY / BLACK ENGINE COMPARTMENT, BRAKE BOOSTER
STEERING ANGLE SENSOR FC110 4-WAY / GREY STEERING COLUMN
WHEEL SPEED SENSOR – LH FRONT FH115 2-WAY / BLACK LH FRONT WHEEL HUB
WHEEL SPEED SENSOR – LH REAR RL1 2-WAY / BLACK LH REAR WHEEL HUB
WHEEL SPEED SENSOR – RH FRONT FH116 2-WAY / BLACK RH FRONT WHEEL HUB
WHEEL SPEED SENSOR – RH REAR RR1 2-WAY / BLACK RH REAR WHEEL HUB
YAW RATE AND LATERAL ACCELERATION SENSORS CLUSTER CA236 6-WAY / BLACK UNDER CENTER CONSOLEHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC10 14-WAY / GREEN / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEM
RL2 2-WAY / BLACK / LH REAR LINK REAR SUSPENSION SUBFRAME RH SIDE
RR2 2-WAY / BLACK / RH REAR LINK REAR SUSPENSION SUBFRAME RH SIDEGROUNDS
Ground LocationFC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Dynamic Stability Control Module
Pin Description and CharacteristicB+ FH103–1 BATTERY POWER SUPPLY – PUMP: B+
— FH103–3 STEERING ANGLE SENSOR SIGNAL (A): PULSED SIGNAL
B+ FH103–4 IGNITION SWITCHED POWER SUPPLY (II): B+
SG FH103–5 SENSOR GROUND – YAW RATE, STEERING ANGLE SENSORS: GROUND
I FH103–6 STEERING ANGLE SENSOR SIGNAL (B): PULSED SIGNAL
SS FH103–7 YAW RATE, STEERING ANGLE SENSORS SUPPLY VOLTAGE: B+
SG FH103–8 BRAKE FLUID LEVEL SENSOR SIGNAL GROUND: GROUND
I FH103–9 BRAKE FLUID LEVEL SENSOR SIGNAL: BRAKE FLUID LEVEL LOW = GROUND
C FH103–11 CAN +
C FH103–12 CAN +
O FH103–13 VEHICLE SPEED SIGNAL (SLIDING ROOF THRESHOLD): < 62 KM/H (38.5 MPH) = GROUND; > 62 KM/H (38.5 MPH) = B+
C FH103–14 CAN –
C FH103–15 CAN –
PG FH103–16 POWER GROUND – VALVES: GROUND
SS FH103–17 ACTIVE BRAKE BOOSTER SOLENOID SUPPLY VOLTAGE: NOMINAL 5 V
SS FH103–18 BRAKE PRESSURE SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
SG FH103–19 SENSOR GROUND – BRAKE PRESSURE SENSOR: GROUND
I FH103–20 BRAKE PRESSURE SENSOR SIGNAL, NOMINAL 0.5 – 4.5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
SG FH103–24 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SIGNAL GROUND: GROUND
C FH103–25 CAN – (LOCAL)
SS FH103–26 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SUPPLY VOLTAGE: NOMINAL 5 V
SS FH103–27 ACTIVE BRAKE BOOSTER FORCE SWITCH NORMALLY OPEN (NOMINAL 5 V): OPEN / CLOSED CIRCUIT
I FH103–28 ACTIVE BRAKE BOOSTER FORCE SWITCH SIGNAL: GROUND
C FH103–29 CAN + (LOCAL)
SS FH103–30 ACTIVE BRAKE BOOSTER FORCE SWITCH NORMALLY CLOSED (NOMINAL 5 V): CLOSED / OPEN CIRCUIT
O FH103–31 ACTIVE BRAKE BOOSTER SOLENOID DRIVE: GROUND (PWM)
B+ FH103–32 BATTERY POWER SUPPLY – VALVES: B+
SG FH103–33 RH FRONT WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–34 RH FRONT WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
I FH103–36 LH REAR WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
SG FH103–37 LH REAR WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–38 DYNAMIC STABILITY CONTROL SWITCH: NORMALLY OPEN / GROUND WHEN ACTIVATED
I FH103–40 ACTIVE BRAKE BOOSTER TRAVEL SENSOR SIGNAL, NOMINAL 0.5 – 4.5 V: VARIABLE VOLTAGE
SG FH103–42 RH REAR WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
I FH103–43 RH REAR WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
I FH103–45 LH FRONT WHEEL SPEED SENSOR SIGNAL: 46 PULSES PER WHEEL REVOLUTION
SG FH103–46 LH FRONT WHEEL SPEED SENSOR SIGNAL GROUND: GROUND
PG FH103–47 POWER GROUND – PUMP: GROUND