2005 INFINITI QX4 fuel
[x] Cancel search: fuelPage 1126 of 3419
COMBINATION METERS
DI-23
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: October 20052005 QX56
4. CHECK HARNESS FOR OPEN OR SHORT CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect combination meter connector M24.
3. Check continuity between fuel level sensor unit and fuel pump
harness connector C5 (A) terminal 2 (Y/L) and combination
meter harness connector M24 (B) terminal 15 (Y/L).
4. Check continuity between fuel level sensor unit and fuel pump
harness connector C5 (A) terminal 2 (Y/L) and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK FUEL LEVEL SENSOR CIRCUIT
1. Check continuity between combination meter harness connector
M24 terminal 16 (B/P) and fuel level sensor unit and fuel pump
harness connector C5 terminal 5 (B/P).
2. Check continuity between fuel level sensor unit and fuel pump
harness connector C5 terminal 5 (B/P) and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness or connector.
6. CHECK FUEL LEVEL SENSOR UNIT
Check the fuel level sensor unit. Refer to DI-25, "
FUEL LEVEL SENSOR UNIT CHECK" .
OK or NG
OK >> GO TO 7.
NG >> Replace the fuel level sensor unit. Refer to FL-5, "
Removal and Installation" .
7. CHECK INSTALLATION CONDITION
Check fuel level sensor unit installation, and determine whether the float arm interferes or binds with any of the
internal components in the fuel tank.
OK or NG
OK >> Replace the combination meter. Refer to IP-13, "Combination Meter" .
NG >> Install the fuel level sensor unit properly.Continuity should exist.
Continuity should not exist.
WKIA4617E
Continuity should exist.
Continuity should not exist.
WKIA2071E
Page 1127 of 3419
DI-24
COMBINATION METERS
Revision: October 20052005 QX56
Fuel Gauge Fluctuates, Indicates Wrong Value, or VariesEKS00BCA
1. CHECK FUEL GAUGE FLUCTUATION
Test drive vehicle to see if gauge fluctuates only during driving or just before or just after stopping.
Does the indication value vary only during driving or just before or just after stopping?
YES >> The fluctuation may be caused by fuel level change in the fuel tank. Condition is normal.
NO >> Ask the customer about the situation when the symptom occurs in detail, Refer to DI-22, "
Fuel
Level Sensor Unit Inspection" .
Fuel Gauge Does Not Move to Full-positionEKS00BCB
1. CHECK POINTER MOVEMENT TO FULL-POSITION
Does it take a long time for the pointer to move to full-position?
YES or NO
YES >> GO TO 2.
NO >> GO TO 3.
2. CHECK IGNITION SWITCH POSITION
Was the vehicle fueled with the ignition switch ON?
YES or NO
YES >> Be sure to fuel the vehicle with the ignition switch OFF. Otherwise, it will take a long time for the
pointer to move to full-position because of the characteristic of the fuel gauge.
NO >> GO TO 3.
3. OBSERVE VEHICLE POSITION
Is the vehicle parked on an incline?
YES or NO
YES >> Check the fuel level indication with vehicle on a level surface.
NO >> GO TO 4.
4. CHECK POINTER MOVEMENT TO EMPTY-POSITION
During driving, does the fuel gauge move gradually toward empty-position?
YES or NO
YES >> Check the fuel level sensor unit. Refer to DI-25, "FUEL LEVEL SENSOR UNIT CHECK" .
NO >> Check fuel level sensor unit installation, and determine whether the float arm interferes or binds
with any of the internal components in the fuel tank.
Page 1128 of 3419
COMBINATION METERS
DI-25
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: October 20052005 QX56
Electrical Components InspectionEKS00BCC
FUEL LEVEL SENSOR UNIT CHECK
For removal, refer to FL-5, "Removal and Installation" .
Check Fuel Level Sensor Unit and Fuel Pump
Check resistance between fuel level sensor unit and fuel pump con-
nector terminals 2 and 5.
*1 and *2: When float rod is in contact with stopper.
Removal and Installation of Combination MeterEKS00BCD
Refer to IP-13, "Combination Meter" for removal and installation procedures.
Terminals Float position mm (in)Resistance
value Ω
(Approx.)
25*1 Empty 25.86 (1.02) 81.66
*2 Full 254.6 (10.02) 6.98
LKIA0402E
Page 1192 of 3419
EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
Revision: October 20052005 QX56 INDEX FOR DTC ........................................................ 8
DTC No. Index ......................................................... 8
Alphabetical Index .................................................. 12
PRECAUTIONS ........................................................ 16
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 16
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 16
Precaution .............................................................. 16
Wiring Diagrams and Trouble Diagnosis ................ 19
PREPARATION ......................................................... 20
Special Service Tools ............................................. 20
Commercial Service Tools ...................................... 22
ENGINE CONTROL SYSTEM .................................. 23
System Diagram ..................................................... 23
Multiport Fuel Injection (MFI) System .................... 24
Electronic Ignition (EI) System ............................... 26
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 27
AIR CONDITIONING CUT CONTROL ..................... 28
Input/Output Signal Chart ....................................... 28
System Description ................................................ 28
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 29
System Description ................................................ 29
Component Description .......................................... 30
CAN COMMUNICATION .......................................... 31
System Description ................................................ 31
EVAPORATIVE EMISSION SYSTEM ....................... 32
Description ............................................................. 32
Component Inspection ........................................... 35
Removal and Installation ........................................ 36
How to Detect Fuel Vapor Leakage ....................... 37
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ...................................................................... 39
System Description ................................................ 39
Diagnostic Procedure ............................................. 40
Component Inspection ........................................... 43
POSITIVE CRANKCASE VENTILATION ................. 45Description .............................................................. 45
Component Inspection ............................................ 45
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ........................................................................ 47
Description .............................................................. 47
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 48
Introduction ............................................................. 48
Two Trip Detection Logic ........................................ 48
Emission-related Diagnostic Information ................ 49
Malfunction Indicator Lamp (MIL) ........................... 64
OBD System Operation Chart ................................ 66
BASIC SERVICE PROCEDURE ............................... 72
Basic Inspection ..................................................... 72
Idle Speed and Ignition Timing Check .................... 77
Idle Mixture Ratio Adjustment ................................. 79
VIN Registration ..................................................... 90
Accelerator Pedal Released Position Learning ...... 90
Throttle Valve Closed Position Learning ................. 90
Idle Air Volume Learning ........................................ 91
Fuel Pressure Check .............................................. 93
TROUBLE DIAGNOSIS ............................................ 95
Trouble Diagnosis Introduction ............................... 95
DTC Inspection Priority Chart ...............................101
Fail-safe Chart ......................................................103
Symptom Matrix Chart ..........................................104
Engine Control Component Parts Location ..........108
Vacuum Hose Drawing .........................................114
Circuit Diagram .....................................................115
ECM Harness Connector Terminal Layout ...........117
ECM Terminals and Reference Value ...................117
CONSULT-II Function (ENGINE) ..........................126
Generic Scan Tool (GST) Function .......................139
CONSULT-II Reference Value in Data Monitor .....141
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................144
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .146
Description ............................................................146
Testing Condition ..................................................146
Inspection Procedure ............................................146
Diagnostic Procedure ...........................................147
Page 1193 of 3419
EC-2Revision: October 20052005 QX56 TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................156
Description ............................................................156
Diagnostic Procedure ...........................................156
POWER SUPPLY AND GROUND CIRCUIT ...........157
Wiring Diagram .....................................................157
Diagnostic Procedure ...........................................158
Ground Inspection ................................................162
DTC U1000, U1001 CAN COMMUNICATION LINE .163
Description ............................................................163
On Board Diagnosis Logic ....................................163
DTC Confirmation Procedure ...............................163
Wiring Diagram .....................................................164
Diagnostic Procedure ...........................................165
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .166
Description ............................................................166
CONSULT-II Reference Value in Data Monitor Mode
.166
On Board Diagnosis Logic ....................................166
DTC Confirmation Procedure ...............................167
Wiring Diagram .....................................................168
Diagnostic Procedure ...........................................171
Component Inspection ..........................................173
Removal and Installation ......................................173
DTC P0101 MAF SENSOR .....................................174
Component Description ........................................174
CONSULT-II Reference Value in Data Monitor Mode
.174
On Board Diagnosis Logic ....................................174
DTC Confirmation Procedure ...............................175
Overall Function Check ........................................176
Wiring Diagram .....................................................177
Diagnostic Procedure ...........................................178
Component Inspection ..........................................181
Removal and Installation ......................................182
DTC P0102, P0103 MAF SENSOR .........................183
Component Description ........................................183
CONSULT-II Reference Value in Data Monitor Mode
.183
On Board Diagnosis Logic ....................................183
DTC Confirmation Procedure ...............................184
Wiring Diagram .....................................................185
Diagnostic Procedure ...........................................186
Component Inspection ..........................................189
Removal and Installation ......................................190
DTC P0112, P0113 IAT SENSOR ...........................191
Component Description ........................................191
On Board Diagnosis Logic ....................................191
DTC Confirmation Procedure ...............................191
Wiring Diagram .....................................................192
Diagnostic Procedure ...........................................193
Component Inspection ..........................................194
Removal and Installation ......................................194
DTC P0117, P0118 ECT SENSOR ..........................195
Component Description ........................................195
On Board Diagnosis Logic ....................................195
DTC Confirmation Procedure ...............................196
Wiring Diagram .....................................................197
Diagnostic Procedure ...........................................198Component Inspection .......................................... 199
Removal and Installation ....................................... 200
DTC P0122, P0123 TP SENSOR ............................ 201
Component Description ........................................ 201
CONSULT-II Reference Value in Data Monitor Mode
. 201
On Board Diagnosis Logic .................................... 201
DTC Confirmation Procedure ................................ 202
Wiring Diagram ..................................................... 203
Diagnostic Procedure ............................................ 204
Component Inspection .......................................... 207
Removal and Installation ....................................... 207
DTC P0125 ECT SENSOR ...................................... 208
Component Description ........................................ 208
On Board Diagnosis Logic .................................... 208
DTC Confirmation Procedure ................................ 209
Diagnostic Procedure ............................................ 209
Component Inspection .......................................... 210
Removal and Installation ....................................... 210
DTC P0127 IAT SENSOR ........................................211
Component Description ........................................211
On Board Diagnosis Logic ....................................211
DTC Confirmation Procedure ................................211
Diagnostic Procedure ............................................ 212
Component Inspection .......................................... 213
Removal and Installation ....................................... 213
DTC P0128 THERMOSTAT FUNCTION ................. 214
On Board Diagnosis Logic .................................... 214
DTC Confirmation Procedure ................................ 214
Diagnostic Procedure ............................................ 214
Component Inspection .......................................... 215
Removal and Installation ....................................... 215
DTC P0138, P0158 HO2S2 ..................................... 216
Component Description ........................................ 216
CONSULT-II Reference Value in Data Monitor Mode
. 216
On Board Diagnosis Logic .................................... 216
DTC Confirmation Procedure ................................ 217
Wiring Diagram ..................................................... 218
Diagnostic Procedure ............................................ 221
Component Inspection .......................................... 223
Removal and Installation ....................................... 224
DTC P0139, P0159 HO2S2 ..................................... 225
Component Description ........................................ 225
CONSULT-II Reference Value in Data Monitor Mode
. 225
On Board Diagnosis Logic .................................... 225
DTC Confirmation Procedure ................................ 226
Overall Function Check ......................................... 226
Wiring Diagram ..................................................... 228
Diagnostic Procedure ............................................ 231
Component Inspection .......................................... 234
Removal and Installation ....................................... 235
DTC P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION .............................................................. 236
On Board Diagnosis Logic .................................... 236
DTC Confirmation Procedure ................................ 236
Wiring Diagram ..................................................... 238
Diagnostic Procedure ............................................ 240
Page 1194 of 3419
EC-3
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: October 20052005 QX56 DTC P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION .............................................................. 245
On Board Diagnosis Logic ................................... 245
DTC Confirmation Procedure ............................... 245
Wiring Diagram .................................................... 247
Diagnostic Procedure ........................................... 249
DTC P0181 FTT SENSOR ...................................... 253
Component Description ........................................ 253
On Board Diagnosis Logic ................................... 253
DTC Confirmation Procedure ............................... 253
Wiring Diagram .................................................... 255
Diagnostic Procedure ........................................... 256
Component Inspection ......................................... 258
Removal and Installation ...................................... 258
DTC P0182, P0183 FTT SENSOR ......................... 259
Component Description ........................................ 259
On Board Diagnosis Logic ................................... 259
DTC Confirmation Procedure ............................... 259
Wiring Diagram .................................................... 260
Diagnostic Procedure ........................................... 261
Component Inspection ......................................... 263
Removal and Installation ...................................... 263
DTC P0222, P0223 TP SENSOR ........................... 264
Component Description ........................................ 264
CONSULT-II Reference Value in Data Monitor Mode
. 264
On Board Diagnosis Logic ................................... 264
DTC Confirmation Procedure ............................... 265
Wiring Diagram .................................................... 266
Diagnostic Procedure ........................................... 267
Component Inspection ......................................... 270
Removal and Installation ...................................... 270
DTC P0300 - P0308 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 8 CYLINDER MISFIRE ..................... 271
On Board Diagnosis Logic ................................... 271
DTC Confirmation Procedure ............................... 271
Diagnostic Procedure ........................................... 272
DTC P0327, P0328, P0332, P0333 KS .................. 279
Component Description ........................................ 279
On Board Diagnosis Logic ................................... 279
DTC Confirmation Procedure ............................... 279
Wiring Diagram .................................................... 280
Diagnostic Procedure ........................................... 281
Component Inspection ......................................... 283
Removal and Installation ...................................... 283
DTC P0335 CKP SENSOR (POS) .......................... 284
Component Description ........................................ 284
CONSULT-II Reference Value in Data Monitor Mode
. 284
On Board Diagnosis Logic ................................... 284
DTC Confirmation Procedure ............................... 284
Wiring Diagram .................................................... 286
Diagnostic Procedure ........................................... 287
Component Inspection ......................................... 290
Removal and Installation ...................................... 290
DTC P0340 CMP SENSOR (PHASE) ..................... 291
Component Description ........................................ 291
On Board Diagnosis Logic ................................... 291
DTC Confirmation Procedure ............................... 291Wiring Diagram .....................................................293
Diagnostic Procedure ...........................................294
Component Inspection ..........................................297
Removal and Installation ......................................297
DTC P0420, P0430 THREE WAY CATALYST FUNC-
TION ........................................................................298
On Board Diagnosis Logic ....................................298
DTC Confirmation Procedure ...............................298
Overall Function Check ........................................299
Diagnostic Procedure ...........................................300
DTC P0441 EVAP CONTROL SYSTEM .................304
System Description ...............................................304
On Board Diagnosis Logic ....................................304
DTC Confirmation Procedure ...............................304
Overall Function Check ........................................305
Diagnostic Procedure ...........................................306
DTC P0442 EVAP CONTROL SYSTEM .................309
On Board Diagnosis Logic ....................................309
DTC Confirmation Procedure ...............................310
Diagnostic Procedure ...........................................311
DTC P0444, P0445 EVAP CANISTER PURGE VOL-
UME CONTROL SOLENOID VALVE ......................318
Description ............................................................318
CONSULT-II Reference Value in Data Monitor Mode
.318
On Board Diagnosis Logic ....................................319
DTC Confirmation Procedure ...............................319
Wiring Diagram .....................................................320
Diagnostic Procedure ...........................................322
Component Inspection ..........................................323
Removal and Installation ......................................324
DTC P0447 EVAP CANISTER VENT CONTROL
VALVE .....................................................................325
Component Description ........................................325
CONSULT-II Reference Value in Data Monitor Mode
.325
On Board Diagnosis Logic ....................................325
DTC Confirmation Procedure ...............................326
Wiring Diagram .....................................................327
Diagnostic Procedure ...........................................328
Component Inspection ..........................................330
DTC P0451 EVAP CONTROL SYSTEM PRESSURE
SENSOR .................................................................332
Component Description ........................................332
CONSULT-II Reference Value in Data Monitor Mode
.332
On Board Diagnosis Logic ....................................332
DTC Confirmation Procedure ...............................333
Diagnostic Procedure ...........................................333
Component Inspection ..........................................334
DTC P0452 EVAP CONTROL SYSTEM PRESSURE
SENSOR .................................................................335
Component Description ........................................335
CONSULT-II Reference Value in Data Monitor Mode
.335
On Board Diagnosis Logic ....................................335
DTC Confirmation Procedure ...............................336
Wiring Diagram .....................................................337
Page 1195 of 3419
EC-4Revision: October 20052005 QX56 Diagnostic Procedure ...........................................338
Component Inspection ..........................................340
DTC P0453 EVAP CONTROL SYSTEM PRESSURE
SENSOR ..................................................................341
Component Description ........................................341
CONSULT-II Reference Value in Data Monitor Mode
.341
On Board Diagnosis Logic ....................................341
DTC Confirmation Procedure ...............................342
Wiring Diagram .....................................................343
Diagnostic Procedure ...........................................344
Component Inspection ..........................................348
DTC P0455 EVAP CONTROL SYSTEM .................349
On Board Diagnosis Logic ....................................349
DTC Confirmation Procedure ...............................350
Diagnostic Procedure ...........................................351
DTC P0456 EVAP CONTROL SYSTEM .................357
On Board Diagnosis Logic ....................................357
DTC Confirmation Procedure ...............................358
Overall Function Check ........................................359
Diagnostic Procedure ...........................................360
DTC P0460 FUEL LEVEL SENSOR .......................366
Component Description ........................................366
On Board Diagnosis Logic ....................................366
DTC Confirmation Procedure ...............................366
Diagnostic Procedure ...........................................367
Removal and Installation ......................................367
DTC P0461 FUEL LEVEL SENSOR .......................368
Component Description ........................................368
On Board Diagnosis Logic ....................................368
Overall Function Check ........................................368
Diagnostic Procedure ...........................................369
Removal and Installation ......................................369
DTC P0462, P0463 FUEL LEVEL SENSOR CIR-
CUIT ........................................................................370
Component Description ........................................370
On Board Diagnosis Logic ....................................370
DTC Confirmation Procedure ...............................370
Diagnostic Procedure ...........................................371
Removal and Installation ......................................371
DTC P0500 VSS ......................................................372
Description ............................................................372
On Board Diagnosis Logic ....................................372
DTC Confirmation Procedure ...............................372
Overall Function Check ........................................372
Diagnostic Procedure ...........................................373
DTC P0506 ISC SYSTEM .......................................374
Description ............................................................374
On Board Diagnosis Logic ....................................374
DTC Confirmation Procedure ...............................374
Diagnostic Procedure ...........................................375
DTC P0507 ISC SYSTEM .......................................376
Description ............................................................376
On Board Diagnosis Logic ....................................376
DTC Confirmation Procedure ...............................376
Diagnostic Procedure ...........................................377
DTC P0550 PSP SENSOR ......................................378
Component Description ........................................378
CONSULT-II Reference Value in Data Monitor Mode . 378
On Board Diagnosis Logic .................................... 378
DTC Confirmation Procedure ................................ 378
Wiring Diagram ..................................................... 379
Diagnostic Procedure ............................................ 380
Component Inspection .......................................... 382
Removal and Installation ....................................... 382
DTC P0605 ECM ..................................................... 383
Component Description ........................................ 383
On Board Diagnosis Logic .................................... 383
DTC Confirmation Procedure ................................ 383
Diagnostic Procedure ............................................ 384
DTC P1031, P1032, P1051, P1052 A/F SENSOR 1
HEATER ................................................................... 386
Description ............................................................ 386
CONSULT-II Reference Value in Data Monitor Mode
. 386
On Board Diagnosis Logic .................................... 386
DTC Confirmation Procedure ................................ 386
Wiring Diagram ..................................................... 387
Diagnostic Procedure ............................................ 390
Component Inspection .......................................... 392
Removal and Installation ....................................... 392
DTC P1065 ECM POWER SUPPLY ........................ 393
Component Description ........................................ 393
On Board Diagnosis Logic .................................... 393
DTC Confirmation Procedure ................................ 393
Wiring Diagram ..................................................... 394
Diagnostic Procedure ............................................ 395
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................. 397
Component Description ........................................ 397
On Board Diagnosis Logic .................................... 397
DTC Confirmation Procedure ................................ 397
Diagnostic Procedure ............................................ 398
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION .............................................................. 399
Description ............................................................ 399
On Board Diagnosis Logic .................................... 399
DTC Confirmation Procedure ................................ 399
Wiring Diagram ..................................................... 400
Diagnostic Procedure ............................................ 401
Component Inspection .......................................... 404
Removal and Installation ....................................... 404
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY ..................................................................... 405
Component Description ........................................ 405
CONSULT-II Reference Value in Data Monitor Mode
. 405
On Board Diagnosis Logic .................................... 405
DTC Confirmation Procedure ................................ 405
Wiring Diagram ..................................................... 407
Diagnostic Procedure ............................................ 408
DTC P1128 THROTTLE CONTROL MOTOR ......... 410
Component Description ........................................ 410
On Board Diagnosis Logic .................................... 410
DTC Confirmation Procedure ................................ 410
Wiring Diagram .....................................................411
Diagnostic Procedure ............................................ 412
Page 1198 of 3419
EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: October 20052005 QX56 DTC P2135 TP SENSOR ........................................ 604
Component Description ........................................ 604
CONSULT-II Reference Value in Data Monitor Mode
. 604
On Board Diagnosis Logic ................................... 604
DTC Confirmation Procedure ............................... 605
Wiring Diagram .................................................... 606
Diagnostic Procedure ........................................... 607
Component Inspection ......................................... 610
Removal and Installation ...................................... 610
DTC P2138 APP SENSOR ...................................... 611
Component Description ......................................... 611
CONSULT-II Reference Value in Data Monitor Mode
.. 611
On Board Diagnosis Logic .................................... 611
DTC Confirmation Procedure ............................... 612
Wiring Diagram .................................................... 613
Diagnostic Procedure ........................................... 614
Component Inspection ......................................... 618
Removal and Installation ...................................... 618
IGNITION SIGNAL .................................................. 619
Component Description ........................................ 619
Wiring Diagram .................................................... 620
Diagnostic Procedure ........................................... 625
Component Inspection ......................................... 629
Removal and Installation ...................................... 630
INJECTOR CIRCUIT ............................................... 631
Component Description ........................................ 631
CONSULT-II Reference Value in Data Monitor Mode
. 631
Wiring Diagram .................................................... 632
Diagnostic Procedure ........................................... 633
Component Inspection ......................................... 636
Removal and Installation ...................................... 636
FUEL PUMP CIRCUIT ............................................ 637
Description ........................................................... 637
CONSULT-II Reference Value in Data Monitor Mode
. 637
Wiring Diagram .................................................... 638
Diagnostic Procedure ........................................... 639
Component Inspection ......................................... 642
Removal and Installation ...................................... 642
REFRIGERANT PRESSURE SENSOR ................. 643
Component Description ........................................ 643Wiring Diagram .....................................................644
Diagnostic Procedure ...........................................645
Removal and Installation ......................................647
ELECTRICAL LOAD SIGNAL ................................648
Description ............................................................648
CONSULT-II Reference Value in Data Monitor Mode
.648
Diagnostic Procedure ...........................................648
ICC BRAKE SWITCH .............................................649
Component Description ........................................649
CONSULT-II Reference Value in Data Monitor Mode
.649
Wiring Diagram .....................................................650
Diagnostic Procedure ...........................................651
Component Inspection ..........................................656
ASCD BRAKE SWITCH .........................................657
Component Description ........................................657
CONSULT-II Reference Value in Data Monitor Mode
.657
Wiring Diagram .....................................................658
Diagnostic Procedure ...........................................659
Component Inspection ..........................................663
ASCD INDICATOR ..................................................664
Component Description ........................................664
CONSULT-II Reference Value in Data Monitor Mode
.664
Wiring Diagram .....................................................665
Diagnostic Procedure ...........................................666
MIL AND DATA LINK CONNECTOR ......................667
Wiring Diagram .....................................................667
SERVICE DATA AND SPECIFICATIONS (SDS) ....669
Fuel Pressure .......................................................669
Idle Speed and Ignition Timing .............................669
Calculated Load Value ..........................................669
Mass Air Flow Sensor ...........................................669
Intake Air Temperature Sensor .............................669
Engine Coolant Temperature Sensor ...................669
A/F Sensor 1 Heater .............................................669
Heated Oxygen sensor 2 Heater ..........................669
Crankshaft Position Sensor (POS) .......................669
Camshaft Position Sensor (PHASE) ....................669
Throttle Control Motor ...........................................669
Injector ..................................................................670
Fuel Pump ............................................................670