2005 INFINITI QX4 stop start

AT-228
SHIFT CONTROL SYSTEM
Revision: October 20052005 QX56
REMOVAL
1. Remove A/T finisher.

Refer to IP-13, "A/T Finisher" .
2. Disconnect selector control cable.
3. Disconnect A/T device harness connector.
4. Remove control device assembly.
INSTALLATION
Installation is in reverse order of removal. Be careful of the following:

After installation is completed, adjust and check A/T position.
Adjustment of A/T PositionECS00CKU
1. Loosen nut of control cable.
2. Place PNP switch and selector lever in “P” position.
3. After pushing the control cable in the direction shown with a
force of 9.8 N·m (1kg-m, 2.2 lb-ft), release it. This is in the natu-
ral state, tighten control cable nut to specifications.
Checking of A/T PositionECS00CKV
1. Place selector lever in “P” position, and turn ignition switch ON
(engine stop).
2. Make sure selector lever can be shifted to other than “P” posi-
tion when brake pedal is depressed. Also make sure selector
lever can be shifted from “P” position only when brake pedal is
depressed.
3. Move the selector lever and check for excessive effort, sticking,
noise or rattle.
4. Confirm the selector lever stops at each position with the feel of
engagement when it is moved through all the positions. Check
whether or not the actual position the selector lever is in
matches the position shown by the shift position indicator and
the transmission body.
5. The method of operating the lever to individual positions correctly should be as shown.
6. Confirm the back-up lamps illuminate only when lever is placed in the “R” position. Confirm the back-up
lamps does not illuminate when selector lever is pushed against “R” position in the “P” or “N” position.
7. Confirm the engine can only be started with the selector lever in the “P” and “N” positions.
8. Make sure transmission is locked completely in “P” position.Control cable nut : 14.5 N·m (1.5 kg-m, 11 ft-lb)
LCIA0345E
LCIA0325E

ATC-34
TROUBLE DIAGNOSIS
Revision: October 20052005 QX56
SELF-DIAGNOSIS
Operation Procedure
1. Touch “SELF-DIAG RESULTS” on “SELECT DIAG MODE”
screen to view all set DTC's.
Display Item List
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch either “MAIN SIGNALS” or “SELECTION FROM MENU” on “DATA MONITOR” screen.
3. When “SELECTION FROM MENU” is selected, touch items to be monitored. When “MAIN SIGNALS” is
selected, all the items will be monitored.
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
BCIA0031E
DTC Description
Reference page
B2573 Battery voltage out of rangeSC-4, "
BATTERY"
B2578 In-vehicle sensor circuit out of range (low)
ATC-140, "In-vehicle Sensor Circuit"B2579 In-vehicle sensor circuit out of range (high)
B257B Ambient sensor circuit short
ATC-137, "
Ambient Sensor Circuit"B257C Ambient sensor circuit open
B257F Optical sensor (Driver) circuit open or short
ATC-143, "
Optical Sensor Circuit"B2580 Optical sensor (Passenger) circuit open or short
B2581 Intake sensor circuit short
ATC-145, "
Intake Sensor Circuit"B2582 Intake sensor circuit open
U1000 CAN bus faultLAN-5, "
CAN COMMUNICATION"
B2587 Stuck buttonATC-147, "FRONT AIR CONTROL"
BCIA0031E
MAIN SIGNALS Monitors all the items.
SELECTION FROM
MENUSelects and monitors the individual item selected.

TROUBLE DIAGNOSIS
ATC-37
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: October 20052005 QX56
DATA MONITOR
Operation Procedure
1. Touch “AIR CONDITIONER” on “SELECT TEST ITEM” screen.
2. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3. Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on
“DATA MONITOR” screen.
4. When “SELECTION FROM MENU” is selected, touch items to
be monitored. When “ALL SIGNALS” is selected, all the items
will be monitored.
5. Touch “START”.
6. Touch “RECORD” while monitoring, then the status of the moni-
tored item can be recorded. To stop recording, touch “STOP”.
Display Item List
WJIA0468E
BCIA0031E
All signals Monitors all the items.
Selection from menu Selects and monitors the individual item selected.
WJIA0469E
Monitor item name “operation or
unit”Contents
IGN ON SW “ON/OFF” Displays “IGN Position (ON)/OFF, ACC Position (OFF)” status as judged from ignition switch signal.
COMP ON SIG “ON/OFF” Displays “COMP (ON)/COMP (OFF)” status as judged from air conditioner switch signal.
FAN ON SIG “ON/OFF” Displays “FAN (ON)/FAN (OFF)” status as judged from blower motor switch signal.

TROUBLE DIAGNOSIS
ATC-127
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: October 20052005 QX56
Low-pressure Side Sometimes Becomes Negative
Low-pressure Side Becomes Negative
Gauge indication Refrigerant cycle Probable cause Corrective action
Low-pressure side sometimes
becomes negative.

Air conditioning system
does not function and does
not cyclically cool the com-
partment air.

The system constantly func-
tions for a certain period of
time after compressor is
stopped and restarted.Refrigerant does not dis-
charge cyclically.
↓
Moisture is frozen at expan-
sion valve outlet and inlet.
↓
Water is mixed with refriger-
ant.

Drain water from refrigerant
or replace refrigerant.

Replace liquid tank.
AC354A
Gauge indication Refrigerant cycle Probable cause Corrective action
Low-pressure side becomes nega-
tive.
Liquid tank or front/rear side of
expansion valve′s pipe is
frosted or dewed.High-pressure side is closed
and refrigerant does not flow.
↓
Expansion valve or liquid tank
is frosted.Leave the system at rest until
no frost is present. Start it
again to check whether or not
the malfunction is caused by
water or foreign particles.

If water is the cause, initially
cooling is okay. Then the
water freezes causing a
blockage. Drain water from
refrigerant or replace refrig-
erant.

If due to foreign particles,
remove expansion valve
and remove the particles
with dry and compressed air
(not shop air).

If either of the above meth-
ods cannot correct the mal-
function, replace expansion
valve.

Replace liquid tank.

Check lubricant for contami-
nation.
AC362A

ATC-192
REFRIGERANT LINES
Revision: October 20052005 QX56
NOTE:
Keep the probe inserted for at least 10 seconds. Use caution not to contaminate the probe tip with
water or dirt that may be in the drain hose.
5. If a leak is detected, verify at least once by blowing compressed air into the area of the suspected leak,
then repeat the leak check.
6. Do not stop when one leak is found. Continue to check for additional leaks at all system components and
connections.
7. If no leaks are found, perform steps 8 - 11.
8. Start the engine.
9. Set the heater A/C controls as follows:
NOTE:
For the automatic system, turn OFF the automatic controls and set the heater A/C controls manually.
a. A/C switch to ON
b. Air flow to VENT mode
c. Intake position to RECIRCULATION mode
d. Temperature to MAX cold
e. Blower speed to HIGH
10. Run the engine at 1,500 rpm for at least 2 minutes.
11. Turn the engine OFF and perform the leak check again following
steps 4 through 6 above.
Refrigerant leaks should be checked immediately after turning
the engine OFF. Begin with the leak detector at the compressor.
The pressure on the high pressure side will gradually drop after
the refrigerant circulation stops and pressure on the low pres-
sure side will gradually rise, as shown in the graph. Some leaks
are more easily detected when the pressure is high.
12. Before connecting the recovery/recycling recharging equipment to the vehicle, check the recovery/recy-
cling recharging equipment gauges. No refrigerant pressure should be displayed. If pressure is displayed,
recover the refrigerant from the equipment lines and then check the refrigerant purity.
13. Confirm refrigerant purity in supply tank using recovery/recycling recharging equipment and refrigerant
identifier equipment (J-41810-NI).
14. Confirm the refrigerant purity in the vehicle's A/C system using recovery/recycling recharging equipment
and refrigerant identifier equipment (J-41810-NI).
15. Discharge the A/C system using recovery/recycling recharging equipment. Repair the leaking fitting or
component as necessary.
16. Evacuate and recharge the A/C system and perform the leak test to confirm that there are no refrigerant
leaks.
17. Conduct the Operational Check to ensure system works properly. Refer to AT C - 5 7 , "
Operational Check
(Front)" and ATC-60, "Operational Check (Rear)" .
SHA8 39 E

AV-2Revision: October 20052005 QX56 “VIEW” MODE ..................................................... 70
“HEADING” MODE .............................................. 71
“NEARBY DISPLAY ICONS” MODE ................... 71
“SAVE CURRENT LOCATION” MODE ............... 71
“ADJUST CURRENT LOCATION” MODE ........... 71
“AUTO RE-ROUTE” MODE ................................. 72
“AVOID AREA SETTINGS” MODE ...................... 72
“CLEAR MEMORY” MODE ................................. 72
“EDIT ADDRESS BOOK” MODE ........................ 73
“GPS INFORMATION” MODE ............................. 73
“QUICK STOP CUSTOMER SETTING” MODE ... 73
“SET AVERAGE SPEED” MODE ........................ 73
“TRACKING” MODE ............................................ 74
GUIDANCE VOLUME ......................................... 74
DISPLAY WITH PUSHED “TRIP” BUTTON ........ 74
TRIP 1 OR TRIP 2 ............................................... 75
FUEL ECONOMY ................................................ 75
MAINTENANCE .................................................. 75
ENGINE OIL OR TIRE ROTATION ..................... 75
TIRE PRESSURE ................................................ 76
WARNING INDICATIONS ................................... 76
CAN Communication System Description .............. 76
Component Parts Location ..................................... 77
Schematic ............................................................... 78
Wiring Diagram — NAVI — ..................................... 79
Schematic ............................................................... 86
Wiring Diagram — COMM — ................................. 87
Terminals and Reference Value for NAVI Control
unit .......................................................................... 90
Terminals and Reference Value for Display Control
unit .......................................................................... 92
Terminals and Reference Value for Display unit ..... 96
Terminals and Reference Value for AV Switch ....... 98
Terminals and Reference Value for BCM ................ 99
On Board Self-Diagnosis Function .......................101
DESCRIPTION ..................................................101
DIAGNOSIS ITEM .............................................101
Self-Diagnosis Mode (DCU) .................................101
OPERATION PROCEDURE ..............................101
SELF–DIAGNOSIS RESULT .............................103
Self-Diagnosis Mode (NAVI) .................................104
OPERATION PROCEDURE ..............................104
SELF–DIAGNOSIS RESULT .............................105
Confirmation/Adjustment Mode ............................107
OPERATION PROCEDURE ..............................107
DISPLAY DIAGNOSIS .......................................108
VEHICLE SIGNALS ...........................................108
NAVIGATION .....................................................109
DISPLAY DIAGNOSIS .......................................109
VEHICLE SIGNALS ...........................................110
HISTORY OF ERRORS ....................................110
DIAGNOSIS BY HISTORY OF ERRORS ..........110
NAVIGATION .....................................................112
CAN DIAG SUPPORT MONITOR ........................114
OPERATION PROCEDURE ..............................114
AV Switch Self-Diagnosis Function .......................115
Power Supply and Ground Circuit Check for NAVI
Control Unit ...........................................................116
Power Supply and Ground Circuit Check for Display Control Unit ...........................................................117
Power Supply and Ground Circuit Check for Display
Unit ........................................................................118
Power Supply and Ground Circuit Check for AV
Switch ................................................................... 120
Vehicle Speed Signal Check for NAVI Control Unit . 121
Vehicle Speed Signal Check for Display Control Unit . 122
Illumination Signal Check for NAVI Control Unit ... 123
Illumination Signal Check for Display Control Unit . 123
Ignition Signal Check for NAVI Control Unit .......... 123
Ignition Signal Check for Display Control Unit ...... 124
Reverse Signal Check for NAVI Control Unit ........ 124
Reverse Signal Check for Display Control Unit .... 124
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) ...................... 125
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) .......................... 126
Display Communication Line Check (Between Dis-
play Control Unit and Display Unit) ....................... 128
AV Communication Line Check (Between Display
Control Unit and AV Switch) .................................. 130
CAN Communication Line Check ......................... 131
If NAVI Control Unit Detects That DVD-ROM Map
is Not Inserted ....................................................... 131
If NAVI Control Unit Detects That Inserted DVD-
ROM Map is Malfunctioning or If It is Impossible to
Load Data from DVD-ROM Map ........................... 131
If Connection Between NAVI Control Unit and GPS
Antenna is Malfunctioning ..................................... 132
Operating Screen for Audio and A/C is Not Dis-
played When Showing NAVI Screen ..................... 132
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Bluish) ............................................ 134
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Reddish) ......................................... 135
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Yellowish) ....................................... 136
Color of RGB Image is Not Proper (All Screen Looks
Bluish) ................................................................... 137
Color of RGB Image is Not Proper (All Screen Looks
Reddish) ................................................................ 138
Color of RGB Image is Not Proper (All Screen Looks
Yellowish) .............................................................. 139
NAVI Screen is Rolling .......................................... 140
Guide Sound is Not Heard .................................... 142
Screen is Not Shown ............................................ 143
A/C Screen is Not Shown (NAVI Screen is Shown) . 143
FUEL ECONOMY Screen is Not Shown ............... 143
Average Fuel Economy Displayed is Not Shown (“
*** ” is Shown) ....................................................... 143
Distance to Empty Displayed is Not Shown (“ *** ”
is Shown) .............................................................. 144
Driving Distance or Average Speed Displayed is Not
Shown (“ *** ” is Shown) ....................................... 144
WARNING DOOR OPEN Screen is Not Shown ... 144
Unable to Operate All of AV Switches (Unable to
Start Self-Diagnosis) ............................................. 145
Audio Does Not Work ........................................... 145
Navigation System Does Not Activate .................. 145

AV-70
NAVIGATION SYSTEM
Revision: October 20052005 QX56
Navigation Setting
How To Perform Navigation Setting
1. Start the engine.
2. Push “SETTING” button.
3. Select “NAVIGATION”.
Application Items
*: Not displayed in Easy Mode.
“VIEW” MODE
1. Select “Birdview™” or “Plan View” icon.

To open the map screen display with Birdview™, select “Bird-
view™”.

To open the map screen display with Plan View, select “Plan
View”.
SKIA0551E
Icon DescriptionReference
page
View Map display mode can be switched.AV- 7 0
HeadingHeading of the map display can be customized for either north heading or the
actual driving direction of the vehicle.AV- 7 1
Nearby Display Icons*Icons of facilities can be displayed.
Facilities to be displayed can be selected from the variety selections.AV- 7 1
Save Current Location* Current vehicle location can be registered in Address Book.AV- 7 1
Adjust Current Location*Current location of position marker can be adjusted. Direction of position marker
also can be calibrated when heading direction of the vehicle on the display is
not matched with the actual direction.AV- 7 1
Auto Re-route On/Off* ON/OFF of Auto Re-route can be switched.AV- 7 2
Avoid Area Setting* A particular area can be avoided when routing.AV- 7 2
Clear Memory* Address Book, Previous destination or Avoid area can be deleted.AV- 7 2
Edit Address Book* Address Book can be edited.AV- 7 3
GPS Information*The GPS data includes longitude, latitude and altitude (distance above sea
level) of the present vehicle position, and current date and time for the area in
which the vehicle is being driven.
Also indicated are the GPS reception conditions and the GPS satellite position.AV- 7 3
Quick Stop Customer Setting* One facility of your selection can be added to your Quick Stop.AV- 7 3
Set Average Speed for Estimated
Journey Time*Average vehicle speed can be set to calibrate estimated journey time for the
destination.AV- 7 3
Tracking On/Off* Tracking to the present vehicle position can be displayed.AV- 7 4
SKIA0554E

NAVIGATION SYSTEM
AV-149
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
DESTINATION, PASSING POINTS, AND MENU ITEMS CANNOT BE SELECTED/SET
VOICE GUIDE
Symptom Cause Remedy
Destination cannot be set. Destination to be set is on an expressway. Set the destination on an ordinary road.
Passing point is not searched
when re-searching the route.The vehicle has already passed the passing point,
or the system judged so.To include the passing points that have been
passed into the route again, set the route
again.
Route information will not be dis-
played.Route searching has not been done. Set the destination and perform route
searching.
Vehicle mark is not on the recommended route. Drive on the recommended route.
Route guide is turned OFF. Turn route guide ON.
Route information is not available on the dark pink
route.System is not malfunctioning.
After the route searching, no guide
sign will appear as the vehicle
goes near the entrance/exit to the
toll road.Vehicle mark is not on the recommended route.
(On the display, only guide signs related to the
recommended route will be shown.)Drive on the recommended route.
Automatic route searching is not
possible.Vehicle is driving on a highway (gray route), or no
recommended route is available.Drive on a road to be searched. Or re–
search the route manually. In this case, how-
ever, the whole route will be searched.
Performed automatic detour
search (or detour search). How-
ever, the result is the same as that
of the previous search.Performed search with every condition consid-
ered. However, the result is the same as that of
the previous search.System is not malfunctioning.
Passing points cannot be set. More than five passing points were set. Passing points can be set up to five. To stop
at more than five points, perform sharing in
several steps.
When setting the route, the start-
ing point cannot be selected.The current vehicle location is always set as the
starting point of a route.System is not malfunctioning.
Some menu items cannot be
selected.The vehicle is being driven. Stop the vehicle at a safe place and then
operate the system.
Symptom Cause Remedy
Voice guide will not operate. Note: Voice guide is only available at intersections
that satisfy certain conditions (indicated by
on
the map). Therefore, guidance may not be given
even when the route on the map changes direc-
tion.System is not malfunctioning.
The vehicle is not on the recommended route. Return to the recommended route or re-
search the route.
Voice guide is turned OFF. Turn voice guide ON.
Route guide is turned OFF. Turn route guide ON.
Voice guide does not match the
actual road pattern.Voice guide may vary with the direction to which
the vehicle is turned and the connection of the
road to other roads.Drive in conformity to the actual traffic rules.