2005 INFINITI FX35 sensor

ON BOARD DIAGNOSTIC (OBD) SYSTEM EC-57
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FXA/F SEN1 HTR (B2) P1051 1051××2×EC-405
A/F SEN1 HTR (B2) P1052 1052 ××2×EC-405
ECM BACK UP/CIRC P1065 1065 — — 2 ×EC-413
I N T / V T I M V / C I R - B 1 P 1111 1111 — — 2 ×EC-417
ETC ACTR P1121 1121 — — 1 ×EC-424
ETC FUNCTION/CIRC P1122 1122 — — 1 ×EC-426
ETC MOT PWR P1124 1124 — — 1 ×EC-432
ETC MOT PWR P1126 1126 — — 1 ×EC-432
E T C M O T P 11 2 8 11 2 8 — — 1 ×EC-437
INT/V TIM V/CIR-B2 P1136 1136 — — 2 ×EC-417
HO2S2 (B1) P1146 1146 ××2×EC-442
HO2S2 (B1) P1147 1147 ××2×EC-453
CLOSED LOOP-B1 P1148 1148 — — 1 ×EC-464
HO2S2 (B2) P1166 1166 ××2×EC-442
HO2S2 (B2) P1167 1167 ××2×EC-453
CLOSED LOOP-B2 P1168 1168 — — 1 ×EC-464
TCS C/U FUNCTN P1211 1211 — — 2 — EC-465
TCS/CIRC P1212 1212 — — 2 —EC-466
ENG OVER TEMP P1217 1217 — — 1×EC-467
CTP LEARNING P1225 1225 — — 2 — EC-479
CTP LEARNING P1226 1226 — — 2 —EC-481
SENSOR POWER/CIRC P1229 1229 — — 1×EC-483
A/F SENSOR1 (B1) P1271 1271 — ×2 ×EC-488
A/F SENSOR1 (B1) P1272 1272 — ×2 ×EC-497
A/F SENSOR1 (B1) P1273 1273 — ×2 ×EC-506
A/F SENSOR1 (B1) P1274 1274 — ×2 ×EC-516
A/F SENSOR1 (B1) P1276 1276 — ×2 ×EC-526
A/F SENSOR1 (B1) P1278 1278 ××2×EC-536
A/F SENSOR1 (B1) P1279 1279 ××2×EC-548
A/F SENSOR1 (B2) P1281 1281 — ×2 ×EC-488
A/F SENSOR1 (B2) P1282 1282 — ×2 ×EC-497
A/F SENSOR1 (B2) P1283 1283 — ×2 ×EC-506
A/F SENSOR1 (B2) P1284 1284 — ×2 ×EC-516
A/F SENSOR1 (B2) P1286 1286 — ×2 ×EC-526
A/F SENSOR1 (B2) P1288 1288 ××2×EC-536
A/F SENSOR1 (B2) P1289 1289 ××2×EC-548
PURG VOLUME CONT/V P1444 1444 — — 2 ×EC-560
VENT CONTROL VALVE P1446 1446 — — 2 ×EC-568
ASCD SW*7P1564 1564 — — 1 — EC-581,
EC-574
ICC COMMAND VALUE*8P1568 1568 — — 1 — EC-587
ASCD BRAKE SW*7P1572 1572 — — 1 — EC-597,
EC-588
Items
(CONSULT-II screen terms) DTC*
1
SRT code
Test value/
Test limit
(GST only) Trip
Reference
page
CONSULT-II
GST*
2ECM*3

EC-58
[VQ35DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2005 July 2005 FX
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: SRT code will not be set if the self-diagnostic result is NG.
*5: The trouble shooting for this DTC needs CONSULT-II.
*6: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*7: For models with ICC or ASCD system.
*8: For models with ICC system.
*9: When the ECM is in the mode of displaying SRT status, MIL may flash. For the details, refer to EC-63, "
How to Display SRT Status" .
DTC AND 1ST TRIP DTC
The 1st trip DTC (whose number is the same as the DTC number) is displayed for the latest self-diagnostic
result obtained. If the ECM memory was cleared previously, and the 1st trip DTC did not reoccur, the 1st trip
DTC will not be displayed.
If a malfunction is detected during the 1st trip, the 1st trip DTC is stored in the ECM memory. The MIL will not
light up (two trip detection logic). If the same malfunction is not detected in the 2nd trip (meeting the required
driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the
2nd trip, both the 1st trip DTC and DTC are stored in the ECM memory and the MIL lights up. In other words,
the DTC is stored in the ECM memory and the MIL lights up when the same malfunction occurs in two consec-
utive trips. If a 1st trip DTC is stored and a non-diagnostic operation is performed between the 1st and 2nd
trips, only the 1st trip DTC will continue to be stored. For malfunctions that blink or light up the MIL during the
1st trip, the DTC and 1st trip DTC are stored in the ECM memory.
Procedures for clearing the DTC and the 1st trip DTC from the ECM memory are described in EC-68, "
HOW
TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION" .
ASCD VHL SPD SEN*7P1574 1574 — — 1 — EC-607,
EC-605
NATS MALFUNCTION P1610 -
P1615 1610 - 1615 — — 2 —
EC-53
TPV SEN/CIRC A/T P1705 1705 — — 1 ×AT-133
P-N POS SW/CIRCUIT P1706 1706 — — 2 ×EC-609
TURBINE REV S/CIRC P1716 1716 — — 2 ×AT-141
A/T INTERLOCK P1730 1730 — — 1 ×AT-145
I/C SOLENOID/CIRC P1752 1752 — — 1 ×AT-150
I/C SOLENOID FNCTN P1754 1754 — — 1 ×AT-152
FR/B SOLENOID/CIRC P1757 1757 — — 1 ×AT-154
FR/B SOLENOID FNCT P1759 1759 — — 1 ×AT-156
D/C SOLENOID/CIRC P1762 1762 — — 1 ×AT-158
D/C SOLENOID FNCTN P1764 1764 — — 1 ×AT-160
HLR/C SOL/CIRC P1767 1767 — — 1 ×AT-162
HLR/C SOL FNCTN P1769 1769 — — 1 ×AT-164
LC/B SOLENOID/CIRC P1772 1772 — — 1 ×AT-166
LC/B SOLENOID FNCT P1774 1774 — — 1 ×AT-168
BRAKE SW/CIRCUIT P1805 1805 — — 2 — EC-614
APP SEN 1/CIRC P2122 2122 — — 1×EC-619
APP SEN 1/CIRC P2123 2123 — — 1 ×EC-619
APP SEN 2/CIRC P2127 2127 — — 1 ×EC-626
APP SEN 2/CIRC P2128 2128 — — 1 ×EC-626
TP SENSOR P2135 2135 — — 1 ×EC-633
APP SENSOR P2138 2138 — — 1 ×EC-640
Items
(CONSULT-II screen terms) DTC*
1
SRT code
Test value/
Test limit
(GST only) Trip
Reference
page
CONSULT-II
GST*
2ECM*3

ON BOARD DIAGNOSTIC (OBD) SYSTEM EC-61
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
SRT Item
The table below shows required self-diagnostic items to set the SRT to “CMPLT”.
*: If completion of several SRTs is required, perform driving patterns (DTC confirmation procedure), one by one based on the pr iority for
models with CONSULT-II.
SRT Set Timing
SRT is set as “CMPLT” after self-diagnosis has been performed one or more times. Completion of SRT is
done regardless of whether the result is OK or NG. The set timing is different between OK and NG results and
is shown in the table below.
OK: Self-diagnosis is carried out and the result is OK.
NG: Self-diagnosis is carried out and the result is NG.
—: Self-diagnosis is not carried out.
When all SRT related self-diagnoses showed OK results in a single cycle (Ignition OFF-ON-OFF), the SRT will
indicate “CMPLT”. → Case 1 above
When all SRT related self-diagnoses showed OK results through several different cycles, the SRT will indicate
“CMPLT” at the time the respective self-diagnoses have at least one OK result. → Case 2 above
SRT item
(CONSULT-II indica- tion) Perfor-
mance Pri- ority* Required self-diagnostic items to set the SRT to “CMPLT”
Corresponding DTC
No.
CATALYST 2 Three way catalyst function P0420, P0430
EVAP SYSTEM 1 EVAP control system P0442
2 EVAP control system P0456
2 EVAP control system purge flow monitoring P0441
HO2S 2 Air fuel ratio (A/F) sensor 1 P1278, P1288
Air fuel ratio (A/F) sensor 1 P1279, P1289
Heated oxygen sensor 2 P0139, P0159
Heated oxygen sensor 2 P1146, P1166
Heated oxygen sensor 2 P1147, P1167
HO2S HTR 2 Air fuel ratio (A/F) sensor 1 heater
P1031, P1032, P1051,
P1052
Heated oxygen sensor 2 heater P0037, P0038, P0057,
P0058
Self-diagnosis result Example
Diagnosis Ignition cycle
← ON → OFF ← ON → OFF ← ON → OFF ← ON →
All OK Case 1 P0400 OK (1) — (1) OK (2) — (2) P0402 OK (1) — (1) — (1) OK (2)
P1402 OK (1) OK (2) — (2) — (2)
SRT of EGR “CMPLT” “CMPLT” “CMPLT” “CMPLT”
Case 2 P0400 OK (1) — (1) — (1) — (1) P0402 — (0) — (0) OK (1) — (1)
P1402 OK (1) OK (2) — (2) — (2)
SRT of EGR “INCMP” “INCMP” “CMPLT” “CMPLT”
NG exists Case 3 P0400 OK OK — — P0402 — — — —
P1402 NG — NG NG
(Consecutive NG)
(1st trip) DTC 1st trip DTC — 1st trip DTC DTC
(= MIL ON)
SRT of EGR “INCMP” “INCMP” “INCMP” “CMPLT”

ON BOARD DIAGNOSTIC (OBD) SYSTEM EC-67
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
Item Self-diagnostic test item DTC Test value
(GST display) Test limit Conversion
TID CID
CATALYST Three way catalyst function (Bank 1)
P0420 01H 01H Max. 1/128
P0420 02H 81H Min. 1
Three way catalyst function (Bank 2) P0430 03H 02H Max. 1/128
P0430 04H 82H Min. 1
EVAP SYSTEM EVAP control system (Small leak) P0442 05H 03H Max.
1/128mm
2
EVAP control system purge flow monitoring P0441 06H 83H Min. 20mV
EVAP control system (Very small leak) P0456 07H 03H Max. 1/128mm
2
HO2S Air fuel ratio (A/F) sensor 1 (Bank 1)
P1271 41H 8EH Min. 5 mV
P1272 42H 0EH Max. 5 mV
P1273 43H 0EH Max. 0.002
P1274 44H 8EH Min. 0.002
P1278 45H 8EH Min. 0.004
P1276 46H 0EH Max. 5 mV
P1276 47H 8EH Min. 5 mV
P1279 48H 8EH Min. 0.004
Air fuel ratio (A/F) sensor 1 (Bank 2) P1281 4CH 8FH Min. 5 mV
P1282 4DH 0FH Max. 5 mV
P1283 4EH 0FH Max. 0.002
P1284 4FH 8FH Min. 0.002
P1288 50H 8FH Min. 0.004
P1286 51H 0FH Max. 5 mV
P1286 52H 8FH Min. 5 mV
P1289 53H 8FH Min. 0.004
Heated oxygen sensor 2 (Bank 1) P0139 19H 86H Min. 10mV/500ms
P1147 1AH 86H Min. 10mV
P1146 1BH 06H Max. 10mV
P0138 1CH 06H Max. 10mV
Heated oxygen sensor 2 (Bank 2) P0159 21H 87H Min. 10mV/500ms
P1167 22H 87H Min. 10mV
P1166 23H 07H Max. 10mV
P0158 24H 07H Max. 10mV
HO2S HEATER Air fuel ratio (A/F) sensor 1 heater (Bank 1)
P1032 57H 10H Max. 5 mV
P1031 58H 90H Min. 5 mV
Air fuel ratio (A/F) sensor 1 heater (Bank 2) P1052 59H 11H Max. 5 mV
P1051 5AH 91H Min. 5 mV
Heated oxygen sensor 2 heater (Bank 1) P0038 2DH 0AH Max. 20mV
P0037 2EH 8AH Min. 20mV
Heated oxygen sensor 2 heater (Bank 2) P0058 2FH 0BH Max. 20mV
P0057 30H 8BH Min. 20mV

EC-70
[VQ35DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2005 July 2005 FX
ON BOARD DIAGNOSTIC SYSTEM FUNCTION
The on board diagnostic system has the following three functions.
When there is an open circuit on MIL circuit, the ECM cannot warn the driver by lighting up MIL when there is
malfunction on engine control system.
Therefore, when electrical controlled throttle and part of ECM related diagnoses are continuously detected as
NG for 5 trips, ECM warns the driver that engine control system malfunctions and MIL circuit is open by means
of operating fail-safe function.
The fail-safe function also operates when above diagnoses except MIL circuit are detected and demands the
driver to repair the malfunction.
MIL Flashing Without DTC
When any SRT codes are not set, MIL may flash without DTC. For the details, refer to EC-63, "How to Display
SRT Status" .
HOW TO SWITCH DIAGNOSTIC TEST MODE
NOTE:

It is better to count the time accurately with a clock.

It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit
has a malfunction.

Always ECM returns to Diagnostic Test Mode I after ignition switch is turned OFF.
How to Set Diagnostic Test Mode II (Self-Diagnostic Results)
1. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
2. Repeat the following procedure quickly 5 times within 5 seconds.
a. Fully depress the accelerator pedal.
b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the MIL starts blinking.
Diagnostic Test
Mode KEY and ENG.
Sta tus Function Explanation of Function
Mode I Ignition switch in ON position
Engine stopped BULB CHECK This function checks the MIL bulb for damage (blown,
open circuit, etc.).
If the MIL does not come on, check MIL circuit.
Engine running MALFUNCTION WARNING This is a usual driving condition. When a malfunction is
detected twice in two consecutive driving cycles (two trip
detection logic), the MIL will light up to inform the driver
that a malfunction has been detected.
The following malfunctions will light up or blink the MIL in
the 1st trip.

Misfire (Possible three way catalyst damage)

One trip detection diagnoses
Mode II Ignition switch in ON position
Engine stopped SELF-DIAGNOSTIC
RESULTS This function allows DTCs and 1st trip DTCs to be read.
Engine operating condition in fail-safe mode Engine speed will not rise more than 2,500 rpm due to the fuel cut

EC-80
[VQ35DE]
BASIC SERVICE PROCEDURE
Revision: 2005 July 2005 FX
6. PERFORM IDLE AIR VOLUME LEARNING
Refer to EC-97, "
Idle Air Volume Learning" .
Is Idle Air Volume Learning carried out successfully?
Ye s o r N o
Yes >> GO TO 7.
No >> 1. Follow the instruction of Idle Air Volume Learning.
2. GO TO 4.
7. CHECK TARGET IDLE SPEED AGAIN
With CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Read idle speed in “DATA MONITOR” mode with CONSULT-II. Refer to EC-83, "
IDLE SPEED" .
Without CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed. Refer to EC-83, "
IDLE SPEED" .
OK or NG
OK >> GO TO 10.
NG >> GO TO 8.
8. DETECT MALFUNCTIONING PART
Check the following.

Check camshaft position sensor (PHASE) and circuit. Refer to EC-307 .

Check crankshaft position sensor (POS) and circuit. Refer to EC-300 .
OK or NG
OK >> GO TO 9.
NG >> 1. Repair or replace.
2. GO TO 4.
9. CHECK ECM FUNCTION
1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2. Perform initialization of IVIS (NATS) system and registration of all IVIS (NATS) ignition key IDs. Refer to EC-53, "
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .
>> GO TO 4.
650
± 50 rpm (in P or N position)
650 ± 50 rpm (in P or N position)
SEF174Y

EC-82
[VQ35DE]
BASIC SERVICE PROCEDURE
Revision: 2005 July 2005 FX
15. CHECK IGNITION TIMING AGAIN
1. Run engine at idle.
2. Check ignition timing with a timing light. Refer to EC-83, "
IGNITION TIMING" .
OK or NG
OK >> GO TO 19.
NG >> GO TO 16.
16. CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Refer to EM-64, "
TIMING CHAIN" .
OK or NG
OK >> GO TO 17.
NG >> 1. Repair the timing chain installation.
2. GO TO 4.
17. DETECT MALFUNCTIONING PART
Check the following.

Check camshaft position sensor (PHASE) and circuit. Refer to EC-307 .

Check crankshaft position sensor (POS) and circuit. Refer to EC-300 .
OK or NG
OK >> GO TO 18.
NG >> 1. Repair or replace.
2. GO TO 4.
18. CHECK ECM FUNCTION
1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2. Perform initialization of IVIS (NATS) system and registration of all IVIS (NATS) ignition key IDs. Refer to EC-53, "
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)" .
>> GO TO 4.
19. INSPECTION END
Did you replace the ECM, referring this Basic Inspection procedure?
Ye s o r N o
Ye s > > 1 . P e r f o r m EC-96, "VIN Registration" .
2. INSPECTION END
No >> INSPECTION END
15
± 5 ° BTDC (in P or N position)
PBIB1602E

BASIC SERVICE PROCEDURE EC-89
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
6. PERFORM IDLE AIR VOLUME LEARNING
Perform EC-97, "
Idle Air Volume Learning" .
Is Idle Air Volume Learning carried out successfully?
Ye s o r N o
Ye s > > G O T O 7 .
No >> 1. Follow the instruction of Idle Air Volume Learning.
2. GO TO 4.
7. CHECK TARGET IDLE SPEED AGAIN
With CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Read idle speed in “DATA MONITOR” mode with CONSULT-II. Refer to EC-83, "
IDLE SPEED" .
Without CONSULT-II
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed. Refer to EC-83, "
IDLE SPEED" .
OK or NG
OK >> GO TO 10.
NG >> GO TO 8.
8. DETECT MALFUNCTIONING PART
Check the following.

Check camshaft position sensor (PHASE) and circuit. Refer to EC-307, "DTC P0340, P0345 CMP SEN-
SOR (PHASE)" .

Check crankshaft position sensor (POS) and circuit. Refer to EC-300, "DTC P0335 CKP SENSOR (POS)"
.
OK or NG
OK >> GO TO 9.
NG >> 1. Repair or replace.
2. GO TO 4.
9. CHECK ECM FUNCTION
1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2. Perform initialization of IVIS (NATS) system and registration of all IVIS (NATS) ignition key IDs. Refer to BL-215, "
ECM Re-Communicating Function" .
>> GO TO 4.
650
± 50 rpm (in P or N position)
650 ± 50 rpm (in P or N position)
SEF174Y