2005 INFINITI FX35 maintenance

ATC-102
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
Self-diagnosisAJS00152
SYMPTOM: Self-diagnosis cannot be performed.
INSPECTION FLOW
*1 Compressor Clutch, ATC-144,
"REMOVAL"
*2 Compressor Clutch, ATC-146,
"INSTALLATION"
*3AT C - 2 7 , "Maintenance of Lubricant
Quantity in Compressor"
*4ATC-61, "Operational Check"*5 EM-15, "Checking Drive Belts"
(VQ35DE) or EM-173, "
Checking
Drive Belts" (VK45DE)
*1 ATC-63, "
Power Supply and Ground
Circuit for Auto Amp."
*2 ATC-104, "Ambient Sensor Circuit"*3ATC-107, "In-vehicle Sensor Circuit"
*4ATC-110, "Sunload Sensor Circuit"*5 ATC-113, "Intake Sensor Circuit"*6AT C - 7 3 , "Air Mix Door Motor Circuit"
*7ATC-61, "Operational Check"*8 ATC-42, "SYMPTOM TABLE"
RJIA2014E

IN-CABIN MICROFILTER ATC-125
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
IN-CABIN MICROFILTERPFP:27277
Removal and InstallationAJS001FC
FUNCTION
Air inside passenger compartment is kept clean at either recircula-
tion or fresh mode by installing in-cabin microfilter into blower unit.
REPLACEMENT TIMING
Replace in-cabin microfilter.
Refer to MA-9, "
CHASSIS AND BODY MAINTENANCE" in Schedule 1 and MA-11, "CHASSIS AND BODY
MAINTENANCE" in Schedule 2.
Caution label is fixed inside glove box.
REPLACEMENT PROCEDURES
1. Remove instrument passenger lower panel. Refer to IP-11, "Removal and Installation" .
2. Remove filter cover, and then remove in-cabin microfilter.
3. Take out in-cabin microfilter from blower unit.
4. Replace with new one and reinstall on blower unit.
5. Reinstall instrument passenger lower panel.
RJIA1331E
RJIA2040E

REFRIGERANT LINES ATC-159
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
Electronic Refrigerant Leak DetectorAJS00166
PRECAUTIONS FOR HANDLING LEAK DETECTOR
When performing a refrigerant leak check, use an A/C electrical leak
detector (SST) or equivalent. Ensure that the instrument is calibrated
and set properly per the operating instructions.
The leak detector is a delicate device. In order to use the leak detec-
tor properly, read the operating instructions and perform any speci-
fied maintenance.
1. Position probe approximately 5 mm (3/16 in) away from point to be checked.
2. When testing, circle each fitting completely with probe.
3. Move probe along component approximately 25 to 50 mm (1 to 2 in)/sec.
SHA196FA
SHA707EA
SHA706E
SHA708EA

AV-2Revision: 2005 July 2005 FX
Window Antenna Repair ......................................
... 54
CHECK ELEMENT ........................................... ... 54
Removal and Installation of Roof Antenna .......... ... 56
REMOVAL ........................................................ ... 56
INSTALLATION ................................................. ... 56
INTEGRATED DISPLAY SYSTEM ......................... ... 57
System Description .............................................. ... 57
A/C AND AV SWITCH SYSTEM ....................... ... 57
PRECAUTION OF LCD MONITOR .................. ... 57
POWER SUPPLY AND GROUND .................... ... 57
DRIVE COMPUTER ......................................... ... 58
E/M SWITCH .................................................... ... 59
SETTING SCREEN .......................................... ... 60
WARNING INDICATIONS ................................ ... 61
AV COMMUNICATION LINE ............................ ... 61
CAN Communication System Description ........... ... 61
CAN Communication Unit .................................... ... 61
Component Parts and Harness Connector Location ... 61
Schematic ............................................................ ... 62
Wiring Diagram — INF/D — ................................ ... 63
Schematic ............................................................ ... 68
Wiring Diagram — COMM — .............................. ... 69
Terminals and Reference Value for Display Unit . ... 72
Terminals and Reference Value for A/C and AV
Switch .................................................................. ... 73
On Board Self-Diagnosis Function ...................... ... 74
DESCRIPTION ................................................. ... 74
DIAGNOSIS ITEM ............................................ ... 74
Self-Diagnosis Mode ........................................... ... 74
OPERATION PROCEDURES .......................... ... 74
NETWORK CHECK .......................................... ... 75
PARTS CHECK ................................................ ... 75
HVAC DETAIL SCREEN ................................... ... 76
VERSION CHECK ............................................ ... 76
CAN DIAG MNTR (CAN DIAG MONITOR) ...... ... 76
A/C and AV Switch Self-Diagnosis Function ........ ... 77
STARTING THE SELF-DIAGNOSIS MODE ..... ... 77
EXITING THE SELF-DIAGNOSIS MODE ........ ... 77
DIAGNOSIS FUNCTION .................................. ... 77
Trouble Diagnosis Chart by Symptom ................. ... 78
Power Supply and Ground Circuit Check for Display
Unit ...................................................................... ... 79
Power Supply and Ground Circuit Check for A/C and
AV Switch ............................................................. ... 80
Vehicle Speed Signal Inspection ......................... ... 80
Illumination Signal Inspection .............................. ... 81
Ignition Signal Inspection ..................................... ... 82
Audio Communication Line Inspection ................ ... 82
AV Communication Line Inspection ..................... ... 84
CAN Communication Line Inspection .................. ... 85
Audio Steering Wheel Switch Inspection ............. ... 86
Removal and Installation of Display ..................... ... 86
REMOVAL ........................................................ ... 86
INSTALLATION ................................................. ... 86
Removal and Installation of A/C and AV Switch .. ... 86
NAVIGATION SYSTEM .......................................... ... 87
System Description .............................................. ... 87
TRAVEL DISTANCE ......................................... ... 87
TRAVEL DIRECTION ....................................... ... 87 MAP-MATCHING ..............................................
... 87
GPS (GLOBAL POSITIONING SYSTEM) ........ ... 88
COMPONENT DESCRIPTION ......................... ... 89
BIRDVIEW™ ..................................................... ... 89
MAP DISPLAY .................................................. ... 90
FUNCTION OF CENTER SWITCH .................. ... 91
“VIEW” MODE ................................................... ... 97
“HEADING” MODE ........................................... ... 98
“NEARBY DISPLAY ICONS” MODE ................. ... 98
“SAVE CURRENT LOCATION” MODE ............. ... 98
“ADJUST CURRENT LOCATION” MODE ........ ... 98
“AUTO RE-ROUTE” MODE .............................. ... 99
“AVOID AREA SETTING” MODE ..................... ... 99
“CLEAR MEMORY” MODE ............................... ... 99
“EDIT ADDRESS BOOK” MODE ...................... .100
“GPS INFORMATION” MODE .......................... .100
“QUICK STOP CUSTOMER SETTING” MODE .100
“SET AVERAGE SPEED” MODE ..................... .100
“TRACKING” MODE ......................................... .101
GUIDANCE VOLUME ....................................... .101
DISPLAY WITH PUSHED “TRIP” BUTTON ...... .101
TRIP 1 OR TRIP 2 ............................................ .102
FUEL ECONOMY ............................................. .102
MAINTENANCE ................................................ .102
ENGINE OIL OR TIRE ROTATION ................... .102
TIRE PRESSURE ............................................. .103
WARNING INDICATIONS ................................. .103
CAN Communication System Description ........... .104
CAN Communication Unit .................................... .104
Component Parts Location and Harness Connector
Location ............................................................... .104
Schematic—NAVI— ............................................. .105
Wiring Diagram —NAVI— .................................... .106
Schematic — COMM — ....................................... .113
Wiring Diagram — COMM — ............................... .114
Terminals and Reference Value for NAVI Control
Unit ....................................................................... .119
Terminals and Reference Value for Display Control
Unit ....................................................................... .121
Terminals and Reference Value for Display ......... .125
Terminals and Reference Value for A/C and AV
Switch .................................................................. .127
On Board Self-Diagnosis Function ....................... .128
DESCRIPTION ................................................. .128
DIAGNOSIS ITEM ............................................ .128
Self-Diagnosis Mode (DCU) ................................. .129
OPERATION PROCEDURE ............................. .129
SELF–DIAGNOSIS RESULT ............................ .130
Self-Diagnosis Mode (NAVI) ................................ .131
OPERATION PROCEDURE ............................. .131
SELF–DIAGNOSIS RESULT ............................ .132
Confirmation/Adjustment Mode ............................ .133
OPERATION PROCEDURE ............................. .133
DISPLAY DIAGNOSIS ...................................... .134
VEHICLE SIGNALS .......................................... .134
AUTO CLIMATE CONTROL ............................. .135
NAVIGATION .................................................... .135
DISPLAY DIAGNOSIS ...................................... .135
VEHICLE SIGNALS .......................................... .136

AV-3
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
HISTORY OF ERRORS ...................................
. 136
DIAGNOSIS BY HISTORY OF ERRORS ........ . 137
NAVIGATION ................................................... . 138
CAN Diag Support Monitor .................................. . 140
OPERATION PROCEDURE ............................ . 140
A/C and AV Switch Self-Diagnosis Function ....... . 141
DESCRIPTION ................................................. . 141
Power Supply and Ground Circuit Check for NAVI
Control Unit ......................................................... . 142
Power Supply and Ground Circuit Check for Display
Control Unit ......................................................... . 143
Power Supply and Ground Circuit Check for Display . 144
Power Supply and Ground Circuit Check for A/C and
AV Switch ............................................................ . 145
Vehicle Speed Signal Check for NAVI Control Unit . 145
Vehicle Speed Signal Check for Display Control Unit . 146
Illumination Signal Check for NAVI Control Unit .. . 147
Illumination Signal Check for Display Control Unit . 148
Ignition Signal Check for NAVI Control Unit ........ . 148
Ignition Signal Check for Display Control Unit .... . 148
Reverse Signal Check for NAVI Control Unit ...... . 148
Reverse Signal Check for Display Control Unit ... . 149
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) .................... . 149
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) ........................ . 150
Display Communication Line Check (Between Dis-
play Control Unit and Display) ............................. . 152
AV Communication Line Check (Between Display
Control Unit and A/C and AV Switch) .................. . 154
CAN Communication Line Check ........................ . 155
If NAVI Control Unit Detects That DVD-ROM Map
Is Not Inserted ..................................................... . 155
If NAVI Control Unit Detects That Inserted DVD-
ROM Map Malfunctioning Or If It Is Impossible to
Load Data from DVD-ROM Map ......................... . 155
If Connection Between NAVI Control Unit and GPS
AntennaIs Malfunctioning .................................... . 156
RGB Screen Is Not Shown .................................. . 156
Color of RGB Image Is Not Proper (NAVI Screen
Looks Bluish) ....................................................... . 157
Color of RGB Image Is Not Proper (NAVI Screen
Looks Reddish) ................................................... . 158
Color of RGB Image Is Not Proper (NAVI Screen
Looks Yellowish) .................................................. . 159
Color of RGB Image Is Not Proper (All Screens
Looks Bluish) ....................................................... . 160
Color of RGB ImageIs Not Proper (All Screens
Looks Reddish) ................................................... . 161
Color of RGB Image Is Not Proper (All Screens
Looks Yellowish) .................................................. . 162
RGB Screen Is Rolling (NAVI Screen) ................ . 163
RGB Screen Is Rolling (Excepting NAVI Screen) . 164
Guide Sound Is Not Heard .................................. . 165
Screen Is Not Shown .......................................... . 166
Audio Screen Is Not Shown (NAVI Screen Is Shown) . 166
A/C Screen Is Not Shown (NAVI Screen Is Shown) . 166
TRIP, FUEL ECON and MAINTENANCE Screens
Are Not Shown .................................................... . 166 Average Fuel Economy Displayed Is Not Shown . 167
Driving Distance or Average Speed Displayed Is Not
Shown .................................................................. .167
WARNING DOOR OPEN Screen Is Not Shown .. .168
Tire Pressure Is Not Displayed ............................ .168
Unable to Operate All of A/C and AV Switch (Unable
to Start Self-Diagnosis) ........................................ .168
Navigation System Does Not Activate ................. .169
Position of Current-Location Mark Is Not Correct . 169
Driving Test .......................................................... .170
Example of Symptoms Judged Not Malfunction .. .171
BASIC OPERATION ......................................... .171
VEHICLE MARK ............................................... .171
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ............. .172
VOICE GUIDE .................................................. .172
ROUTE SEARCH ............................................. .172
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT ............................................. .174
CURRENT LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ....... .177
CURRENT-LOCATION MARK JUMPS ............ .177
CURRENT LOCATION MARK IS IN A RIVER OR
SEA .................................................................. .178
WHEN DRIVING ON SAME ROAD, SOME-
TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE .............................................................. .178
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ................................................... .178
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ............................... .178
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED ............................................................ .178
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ....... .178
Program Loading of NAVI Control Unit ................ .179
Removal and Installation of NAVI Control Unit .... .180
REMOVAL ........................................................ .180
INSTALLATION ................................................ .180
Removal and Installation of GPS Antenna .......... .180
REMOVAL ........................................................ .180
INSTALLATION ................................................ .180
Removal and Installation of A/C and AV Switch .. .181
Removal and Installation of Display Unit ............. .181
Removal and Installation of Display Control Unit . 181 REMOVAL ........................................................ .181
INSTALLATION ................................................ .181
INFINITI MOBILE ENTERTAINMENT SYSTEM .... .182
System Description .............................................. .182
Component Parts and Harness Connector Location .183
Wiring Diagram – MES – ..................................... .184
Terminals and Reference Value for DVD Player .. .186
Terminals and Reference Value for DVD Display . 187
DVD Player Does Not Work ................................ .189
Screen Is Not Shown (While Sounds Come Out of
an Audio Speaker, Did Not Do of a Head Phone) .191
Screen Is not Shown (Sounds Come Out of Both

PRECAUTIONS AV-5
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS007X5
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

INTEGRATED DISPLAY SYSTEM AV-59
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
MAINT Switch (Maintenance Switch)

When “MAINT” switch is pressed, display vehicle information screen. As vehicle information, it indicates
engine oil, tire rotation, tire pressure.

Pressing “MAINT” switch once cycles display from engine oil →tire rotation →tire pressure →display
OFF →engine oil.
Engine Oil and Tire Rotation

Operating the joystick left/right, replace distance can be set.

When journey distance is the same as replace distance, alert is
displayed. (SERVICE ALERT setting is ON.)

Selected replace distance is 0 - 7,500 miles (0 - 12,000 km) in
increments of 500 mile (800 km).

Press and hold “TRIP RESET or MAINT” switch for 1.5 seconds
or longer, reset present journey distance.

During driving, cannot change settings.
Tire Pressure

Tire pressure signal is received from BCM through CAN commu-
nication line.

Tire pressure is displayed.

When FLAT TIRE signal is received from BCM, “FLAT TIRE” is
displayed.
E/M SWITCH
When “E/M” (English/Metric) switch is pressed, change the unit as followings.
SKIA5918E
SKIA5919E
Unit US Mile,
°F, M P G
Metric km, °C, l/100km

NAVIGATION SYSTEM AV-101
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
“TRACKING” MODE

To delete the tracking marks on the map, select “Off”.

To leave the tracking marks on the map, select “On”.
NOTE:
When a trail display is turned OFF, trail data is erased from the mem-
ory.
GUIDANCE VOLUME
Description
Following guidance volume setting can be changed.
Activation/Deactivation Setting

The voice prompt can be turned on/off by pressing the “Guidance Volume” button.
Voice Volume Setting

Volume of the voice can be controlled by bending the joystick to left/right.
DISPLAY WITH PUSHED “TRIP” BUTTON

When the “TRIP” button is pushed, the following models will display on the screen.

Warning message (if there are any) →TRIP1 →TRIP2 →FUEL ECONOMY →MAINTENANCE →OFF.
SKIA0559E
SKIA4497E
Display items Display/Setting contents Reference
page
Trip 1 o r Trip2 Elapsed Time Displays driving time with a range of 0000:00:00 to 9999:59:59.
AV-102,
"TRIP 1 OR
TRIP 2"
Driving Distance
[(km) or (miles)] Displays driving distance with a range of 00000.0 to 99999.9.
Average speed
[(km/h) or (MPH)] Displays average speed with a range of 000.0 to 999.9.
Fuel Economy Average Fuel Economy
[(MPG) or (l/100km)] Displays fuel economy with ignition switch ON, average fuel econ-
omy each 30 minutes. AV-102,
"FUEL
ECONOMY"
Distance to Empty [(km) or
(miles)], [(MPG) or (l/100km)] Displays possible driving distance with remaining fuel.
Fuel Economy (MPG) Displays fuel economy each approx. 100 ms.
Maintenance Engine oil Maintenance intervals of engine oil and setting of oil change cycle.
AV-102,
"MAINTE-
NANCE"
Tire rotation Maintenance intervals of tire and setting of tire replacement cycle.
Tire pressure Tire pressure displayed as tire pressure information.