2005 GMC ENVOY XUV lock

3. Clip the second row safety belts into the retainers.
They are mounted on the pillars below where the
safety belt passes through the trim panel. This
prevents the safety belt from being tangled in the
midgate when opening or closing the midgate.
4. Press the midgate release button located on the
driver’s side of the midgate while pulling the
release handle.
5. Lower the midgate and secure it in the down
position by engaging the midgate to the oor
support. The latch for the oor support is found on
the driver’s side of the vehicle.
Raising the Midgate
To return the midgate to its normal position, release the
midgate by pulling up on the lever found on the
driver’s side midgate support. Reverse the steps for
lowering the midgate listed previously. The midgate
must be fully latched on both sides before the midgate
glass can be raised.
Tailgate
Your vehicle is equipped with a tailgate which can be
swung out or opened at. It can be locked and unlocked
with the driver or passenger door power lock button
or the remote keyless entry transmitter. The tailgate has
power rear glass. The glass must be fully lowered to
open the tailgate to its at position.
The power roof and tailgate must both be fully closed to
raise the rear glass. If the roof or tailgate are not fully
closed, the words CLOSE THE ROOF or CLOSE
THE TAILGATE will appear on the DIC when you try
to raise the rear glass.
If the tailgate drop/swing, power roof, rear wiper and
rear window defogger functions are inoperative, or
SEE MANUAL– TAILGATE is displayed on the Driver
Information Center, the tailgate window position needs to
be reset. To reset the window position, activate the
tailgate window up switch and continue to hold it
for two seconds after the window is fully closed.
Then activate the tailgate window down switch and
continue to hold it for two seconds after the window is
fully open. If this process does not restore function,
see your dealer for service.
2-14

Using the Overhead Console Switch to
Operate the Tailgate Rear Glass
To operate the tailgate glass using the overhead
console roof switch, the ignition must be in RUN or
ACCESSORY or Retained Accessory Power (RAP)
must be active.
E(Tailgate glass): Press and hold this switch to
fully open the tailgate glass.
To open the tailgate glass slightly, lightly press the
front of the tailgate glass switch. To close the tailgate
glass, press and hold the rear of the tailgate glass switch.
Using the Tailgate Key Cylinder to
Operate Tailgate Glass
To open the tailgate glass, rotate the tailgate key
clockwise. If the power roof is not fully closed, a
counterclockwise rotation of the key will rst close
the roof. Return the key to neutral, then rotate it
counterclockwise to close the tailgate glass after the
roof has been closed.
Using the Cargo Area Window Button
Press and release the
button located in the
cargo area on the driver’s
side of the vehicle to
fully lower the glass in
an express mode.
The cargo area button will only lower the tailgate glass
when the vehicle is in PARK (P).
Using the Remote Keyless Entry
Transmitter
Press the tailgate glass button twice on the remote
keyless entry transmitter to fully lower the glass in an
express mode.
2-15

Opening the Tailgate
To open the tailgate, the vehicle must be in PARK (P)
and the doors must be unlocked. To open the tailgate to
a at position, the tailgate glass must rst be fully
lowered. Once the tailgate glass has been fully lowered,
open the tailgate by grasping its handle near the
middle and pulling the gate toward you.
To close the tailgate, use the integrated pocket at the
top of the tailgate. Firmly push the tailgate upward
until it latches. Do not grab the wiper arm/blade to close
the tailgate.
Notice:Closing the tailgate using the wiper
arm/blade may damage the vehicle. Close the
tailgate using only the pocket.
To swing the tailgate out, grasp the tailgate by its handle
near the driver’s side. If the tailgate glass is fully
closed, it will rst drop slightly to clear the upper roof
seal. The tailgate may then be swung out. If you release
the handle before the tailgate opens, the glass will
return to the fully closed position.
To close the tailgate, rmly push it toward the vehicle
until it latches. If the tailgate glass was fully closed when
you opened the tailgate, it will return to a fully closed
position when you close the tailgate.The tailgate is equipped with a prop rod to aid in
supporting heavy loads and to support four foot by
eight foot building material when placed in the
secondary position. In the secondary position, the
tailgate is raised approximately six degrees. With the
tailgate in the at position, remove the prop rod from the
retaining clip on the driver’s side. Rotate the rod forward
and engage the end of the slotted stud on the side of
the vehicle opening. Push down to lock the rod in place.
Two slotted studs on the vehicle provide two positions
for the tailgate. The prop rod must be in the stowed
position and secured in the retaining clip before closing
the tailgate.Tailgate Prop Rod
2-16

When a roof operation is halted because of an
obstruction such as ice, snow or an object in the
opening, the words CLEAR ROOF OBSTRUCTION will
appear on the DIC. Clear the roof obstruction and
then operate the roof.
Notice:If you attempt to operate the power roof
when it is frozen or blocked by ice or snow, you may
damage the power roof mechanism. Do not attempt
to operate the power roof when it is frozen or
blocked by ice or snow.
For information on cleaning the roof track, seeCleaning
the Roof Track on page 5-89.
Using the Tailgate Key Cylinder
To operate the power roof using the tailgate key
cylinder, the rear glass must be fully lowered. Turn and
hold the key clockwise to lower the rear glass. Once
the glass is completely lowered, the roof may be opened
by returning the key to the neutral (vertical) position
and then turning and holding the key clockwise again.
The roof may be closed by turning and holding the
key counterclockwise. Maintain the key in the
counterclockwise position until the roof is fully closed.
Resetting the Roof Position
The words OPEN THE ROOF may appear on the DIC.
This indicates a need to reset the roof position.
When this message appears, place the vehicle in
PARK (P) and the ignition in RUN or ACCESSORY.
Open the power roof using the power roof switch in
the overhead console. When the roof has fully opened,
the words CLOSE THE ROOF will appear and a
chime will sound. This completes the rst step of the
roof reset process.
With the vehicle still in PARK (P) and the ignition in
RUN or ACCESSORY, close the power roof using the
power roof switch in the overhead console until the
words ROOF IS CLOSED appear and a chime sounds.
If the words ROOF IS CLOSED do not appear within
one minute or the roof does not operate after this reset
process, see your dealer for service.
Resetting the Rear Glass Position
The words TAILGATE — SEE MANUAL may appear
on the DIC after the rear glass has been fully lowered
and the roof has not moved. Although this message
may appear when you attempt to operate the roof,
it indicates a need to reset the rear glass position.
2-19

Power Windows
The controls for the power windows are located on the
armrest on each of the side doors. With power windows,
the switches operate the windows when the ignition is in
RUN, ACCESSORY or when Retained Accessory Power
(RAP) is active. SeeRetained Accessory Power (RAP)
on page 2-25. The driver’s door has a switch for each of
the passenger’s windows as well.
Press the top or bottom of the switch to raise or lower
the window. If you hold the switch down for three to
seven seconds after the window has been completely
lowered or raised, the window will not operate for about
15 seconds.
Express-Down Window
AUTO (Express-down):The driver’s and front
passenger’s window switches have an express-down
feature that allows you to lower the window without
holding the switch down. Press down briey on
the bottom of the driver’s or front passenger’s window
switch labeled AUTO to activate the express-down
feature. Lightly tap the switch to open the window
slightly. The express-down feature can be interrupted at
any time by pressing the top of the switch.
Window Lockout
o
(Lockout):Your vehicle has a lockout feature to
prevent passengers from operating the power windows.
The lockout switch is located in front of the window
switches on the driver’s door. A light in the lockout
switch will come on to show that the switch has been
activated. Press the lockout switch again to return
to normal operation.
2-21

Sun Visors
To block out glare, you can pull the visor down. You can
also slide the visor along the rod from side-to-side to
cover the driver or passenger front window.
Visor Vanity Mirror
Pull the sun visor down to expose the vanity mirror.
Lighted Visor Vanity Mirror
Your vehicle may have this feature. Pull the sun visor
down and lift the mirror cover to turn on the lamps.
The lamps will turn off when the cover is closed.
Theft-Deterrent Systems
Vehicle theft is big business, especially in some cities.
Although your vehicle has a number of theft-deterrent
features, we know that nothing we put on it can make it
impossible to steal.
Content Theft-Deterrent
Your vehicle may be
equipped with a content
theft-deterrent alarm
system. If so, this security
light will appear on the
instrument panel cluster.
Here’s how to operate the system:
1. Open the door.
2. Lock the door with the power door lock switch or
the remote keyless entry transmitter. The security
light should come on and stay on.
3. Close all doors. The security light should turn off
after approximately 30 seconds. The alarm is not
armed until the security light turns off.
2-22

If a locked door is opened without the key or the remote
keyless entry transmitter, the alarm will go off. The
headlamps and parking lamps will ash for two minutes,
and the horn will sound for 30 seconds, then will turn
off to save the battery power.
Remember, the theft-deterrent system won’t activate
if you lock the doors with a key or use the manual door
lock. It activates only if you use a power door lock
switch with the door open, or with the remote keyless
entry transmitter. You should also remember that
you can start your vehicle with the correct ignition key
if the alarm has been set off.
Here’s how to avoid setting off the alarm by accident:
If you don’t want to activate the theft-deterrent
system, the vehicle should be locked with the door
keyafterthe doors are closed.
Always unlock a door with a key, or use the remote
keyless entry transmitter. Unlocking a door any
other way will set off the alarm.
If you set off the alarm by accident, unlock any door
with the key. You can also turn off the alarm by
pressing unlock on the remote keyless entry transmitter.
The alarm won’t stop if you try to unlock a door any
other way.
Testing the Alarm
The alarm can be tested by following these steps:
1. From inside the vehicle, lower the driver’s window
and open the driver’s door.
2. Activate the system by locking the doors with the
power door lock switch while the door is open, or
with the remote keyless entry transmitter.
3. Get out of the vehicle, close the door and wait for
the security light to go out.
4. Then reach in through the window, unlock the door
with the manual door lock and open the door.
This should set off the alarm.
When the alarm is set the power door unlock switch is
not operational.
If the alarm does not sound when it should but the
headlamps ash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse,
seeFuses and Circuit Breakers on page 5-97.
If the alarm does not sound or the headlamps do not
ash, the vehicle should be serviced by your dealer.
2-23

Passlock®
Your vehicle is equipped with the Passlock®
theft-deterrent system.
Passlock
®is a passive theft-deterrent system.
Passlock®enables fuel if the ignition lock cylinder is
turned with a valid key. If a correct key is not used or the
ignition lock cylinder is tampered with, the fuel system
is disabled and the vehicle will not start.
During normal operation, the security light will turn off
approximately ve seconds after the key is turned
to RUN.
If the engine stalls and the security light ashes, wait
about 10 minutes until the light stops ashing before
trying to restart the engine. Remember to release
the key from START as soon as the engine starts.
If the engine does not start after three tries, the vehicle
needs service.
If the engine is running and the security light comes on,
you will be able to restart the engine if you turn the
engine off. However, your Passlock
®system is
not working properly and must be serviced by your
dealer. Your vehicle is not protected by Passlock
®
at this time. You may also want to check the fuse.
See your dealer for service.
Starting and Operating
Your Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an elaborate
break-in. But it will perform better in the long run if
you follow these guidelines:
Keep your speed at 55 mph (88 km/h) or less
for the rst 500 miles (805 km).
Do not drive at any one speed — fast or
slow — for the rst 500 miles (805 km).
Do not make full-throttle starts.
Avoid making hard stops for the rst 200 miles
(322 km) or so. During this time your new brake
linings are not yet broken in. Hard stops with new
linings can mean premature wear and earlier
replacement. Follow this breaking-in guideline
every time you get new brake linings.
Do not tow a trailer during break-in. SeeTowing a
Trailer on page 4-55for more information.
2-24