2005 DODGE POWER WAGON Owners Manual

FUSE AND RELAY CENTER
Your vehicle is equipped with a fuse and relay center
located in the engine compartment near the battery.
Located on the underside of the cover is a label that
identifies each component.
1. Disconnect the battery negative (-) cable before remov-
ing the cover.2. Use specified fuses only.
3. Always properly reinstall the cover.
VEHICLE STORAGE
If you are storing your vehicle for more than 21 days, we
recommend that you take the following steps to mini-
mize the drain on your vehicle’s battery:
•Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse
located in the Fuse and Relay Center, located in the
engine compartment. The I.O.D. cavity includes a
snap-in retainer that allows the fuse to be discon-
nected, without removing it from the fuse block.
•The electronic shift transfer case should be placed in
the 4HI mode and kept in this position to minimize the
battery drain.
•As an alternative to the above steps you may, discon-
nect the negative cables from both batteries.
MAINTAINING YOUR VEHICLE 393
7

REPLACEMENT LIGHT BULBS
LIGHT BULBS—Inside Bulb No.
Overhead Console Lights............... TS212-2
Dome Light............................7679
All of the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved.
LIGHT BULBS—Outside Bulb No.
Back-Up..............................3057
Center High Mounted Stop Lamp............. 912
Fog Lamp...........................9006LL
Headlamp (Halogen)...................9007QL
Park & Turn Signal...................3157NAK
Rear License Plate Lamp................... 168
Rear Cargo Light......................... 912
Tail & Stop............................3057
BULB REPLACEMENT
Headlight (Halogen)/Front Park and Turn Lights
CAUTION!
This is a halogen bulb. Avoid touching the glass
with your fingers. Reduced bulb life will result.
394 MAINTAINING YOUR VEHICLE

1. Remove the expanding fastener from the headlight
welt.
MAINTAINING YOUR VEHICLE 395
7

2. Remove the three (3) bolts from the headlight housing.
NOTE:The lower bolt on the driver side headlight also
retains the ambient temperature sensor between the
headlight assembly and the frame.
396 MAINTAINING YOUR VEHICLE

3. Pull the housing out from the fender to allow room to
disconnect the electrical connectors.4. Unlock and pull connector straight from the base of
the headlight halogen bulb.
5. Twist connector on turn signal/park light bulb
1⁄4turn
and remove connector and bulb from housing.
6. Remove housing from vehicle with headlight halogen
bulb in housing.
MAINTAINING YOUR VEHICLE 397
7

7. Twist collar on headlight halogen bulb1⁄4turn and
remove headlight bulb from the housing.
8. Replace headlight or turn signal bulb. Do not touch
the headlight halogen bulb.
9. Reverse procedure for installation of bulbs and hous-
ing.
10. Tighten the outboard fastener first.
Tail, Stop, Turn and Backup Lights
1. Remove the two (2) screws that pass through the bed
sheetmetal.
398 MAINTAINING YOUR VEHICLE

2. Pull the housing straight out from the body, with a
quick motion, to separate the housing from the body. If
not pulled straight, locators may be damaged.3. Push the red lock slide in on the connector and remove
the housing from the vehicle.
4. Remove the four (4) screws from the bulb strip in the
housing.
MAINTAINING YOUR VEHICLE 399
7

5. Pull the appropriate bulb straight from the bulb strip.
•Top Bulb: Park/Turn/Hazard
•Center Bulb: Stop/Park/Sidemarker
•Bottom Bulb: Backup Lights
6. Reverse procedure for installation of bulbs and hous-
ing.7. While holding the taillight firmly in place, fasten the
top screw first.
Center High-Mounted Stoplight With Cargo Light
1. Remove the two (2) screws holding the housing/lens
to the body as shown.
400 MAINTAINING YOUR VEHICLE